| /Modules/Sensors/ALTIMET01A/SW/PIC/PIC16F887/main.c |
|---|
| 0,0 → 1,66 |
| #include <16f887.h> |
| #fuses HS, NOWDT, NOPROTECT, BROWNOUT, PUT, NOLVP |
| #use delay(clock = 20000000) |
| #use rs232(baud=57600, xmit=PIN_C6, rcv=PIN_C7) |
| #define CSN_SPI PIN_C2 |
| int8 address, uiTadc, data ; |
| // SPI mode definitions. |
| #define SPI_MODE_0 (SPI_L_TO_H | SPI_XMIT_L_TO_H) |
| #define SPI_MODE_1 (SPI_L_TO_H) |
| #define SPI_MODE_2 (SPI_H_TO_L) |
| #define SPI_MODE_3 (SPI_H_TO_L | SPI_XMIT_L_TO_H) |
| void main() |
| { |
| printf("Start\n\r"); |
| setup_spi(SPI_MASTER | SPI_MODE_0 | SPI_CLK_DIV_64); |
| output_high(CSN_SPI); |
| delay_ms(100); |
| while(true) |
| { |
| data = 5; //just to be sure that the value is updated |
| //Start temperature and pressure conversion |
| address = 0x24; |
| address &= 0x7F; |
| output_low(CSN_SPI); |
| delay_ms(1); |
| spi_write(address); |
| delay_ms(1); |
| spi_write(0x00); |
| delay_ms(1); |
| output_high(CSN_SPI); |
| delay_ms(2); |
| // get MSB for Pressure |
| address = 0x00; |
| address |= 0x80; |
| output_low(CSN_SPI); |
| delay_ms(1); |
| spi_write(address); |
| delay_ms(1); |
| data = spi_read(0x00); |
| delay_ms(1); |
| output_high(CSN_SPI); |
| printf("%u\n\r", data); |
| //uiTadc = (unsigned int) data << 8; |
| //printf("%u\n\r", uiTadc); |
| delay_ms(100); |
| } |
| } |
| /Modules/Sensors/ALTIMET01A/SW/PIC/PIC16F887/main.h |
|---|
| 0,0 → 1,20 |
| #include <16F887.h> |
| #device adc=10 |
| #FUSES NOWDT //No Watch Dog Timer |
| #FUSES INTRC //Internal RC Osc |
| #FUSES NOPUT //No Power Up Timer |
| #FUSES MCLR //Master Clear pin enabled |
| #FUSES NOPROTECT //Code not protected from reading |
| #FUSES NOCPD //No EE protection |
| #FUSES NOBROWNOUT //No brownout reset |
| #FUSES IESO //Internal External Switch Over mode enabled |
| #FUSES FCMEN //Fail-safe clock monitor enabled |
| #FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
| #FUSES NODEBUG //No Debug mode for ICD |
| #FUSES NOWRT //Program memory not write protected |
| #FUSES BORV40 //Brownout reset at 4.0V |
| #use delay(clock=8000000) |
| #use rs232(baud=9600,parity=N,xmit=PIN_B7,rcv=PIN_B6,bits=8) |
| /Modules/Sensors/ALTIMET01A/SW/PIC/PIC16F887/main.pjt |
|---|
| 0,0 → 1,31 |
| [PROJECT] |
| Target=main.hex |
| Development_Mode= |
| Processor_Text=PIC16F887 |
| ToolSuite=CCS |
| Processor=0x887F |
| [main] |
| Type=4 |
| Path= |
| FileList= |
| BuildTool= |
| OptionString= |
| AdditionalOptionString= |
| [mru-list] |
| 1=main.c |
| [Windows] |
| 0=0000 %S 0 0 796 451 3 0 |
| [Opened Files] |
| 1=main.c |
| 2= |
| 3=C:\Program Files\PICC\devices\16F887.h |
| 4=C:\Program Files\PICC\drivers\lcd.c |
| 5=..\ds1820.c |
| 6=..\1wire.c |
| 7= |
| [Target Data] |
| OptionString=-p +FM |
| FileList=D:\MLAB\Designs\Thermometer\SW\PIC16F887\main.c |
| [Units] |
| Count=1 |
| 1=main (main) |