| 0,0 → 1,112 |
|---|
| // Gas Discharge Lamps controller |
| #define VERSION "$Revision: 3654 $" |
| |
| |
| // Triacs |
| int t1 = 2; // PD2 - lamp 1 |
| int t2 = 3; // PD3 - lamp 2 |
| int t3 = 4; // PD4 - |
| int t4 = 5; // PD5 - |
| int t5 = 6; // PD6 - |
| int t6 = 7; // PD7 |
| int t7 = 8; // PB0 |
| int t8 = 9; // PB1 |
| |
| int n; // Counter |
| char state; // State of Gas Lamps |
| |
| void info () // Print an information string |
| { |
| Serial.print("Gas Discharge Lamps Controller "); |
| Serial.println(VERSION); |
| Serial.println("Commands: abcdefghABCDEFGHitRS"); |
| Serial.println("a = OFF lamp 1 / A = ON lamp 1"); |
| Serial.println("i = info"); |
| Serial.println("t = telemetry"); |
| Serial.println("R = reset"); |
| } |
| |
| |
| void pstatus() // Print status to serial line |
| { |
| for (n=1;n<=8;n++) |
| { |
| if(digitalRead(n+1)) |
| { |
| Serial.print((char)('A'+n-1)); |
| } |
| else |
| { |
| Serial.print((char)('a'+n-1)); |
| } |
| } |
| Serial.println(); |
| } |
| |
| |
| // the setup routine runs once when you press reset: |
| void setup() |
| { |
| // initialize the digital pin as an output and switch off |
| digitalWrite(t1, LOW); |
| digitalWrite(t2, LOW); |
| digitalWrite(t3, LOW); |
| digitalWrite(t4, LOW); |
| digitalWrite(t5, LOW); |
| digitalWrite(t6, LOW); |
| digitalWrite(t7, LOW); |
| digitalWrite(t8, LOW); |
| pinMode(t1, OUTPUT); |
| pinMode(t2, OUTPUT); |
| pinMode(t3, OUTPUT); |
| pinMode(t4, OUTPUT); |
| pinMode(t5, OUTPUT); |
| pinMode(t6, OUTPUT); |
| pinMode(t7, OUTPUT); |
| pinMode(t8, OUTPUT); |
| state = 'a'; |
| |
| // initialize the serial port |
| Serial.begin(9600); |
| Serial.println(); |
| Serial.println("Cvak."); |
| |
| Serial.println("Hmmm...."); |
| info(); |
| } |
| |
| // the loop routine runs over and over again forever: |
| void loop() |
| { |
| byte inByte; // Character from serial line |
| |
| if (Serial.available() > 0) // wait for a char |
| { |
| // get incoming byte: |
| inByte = Serial.read(); |
| |
| switch (inByte) |
| { |
| case 'i': // Print Info |
| info(); |
| break; |
| |
| case 'R': // Reset |
| asm volatile (" jmp 0"); |
| break; |
| |
| } |
| |
| if ( (inByte >= 'a') and (inByte <= 'h')) // Switch OFF other triacs |
| { |
| digitalWrite(inByte-'a'+2,LOW); |
| } |
| |
| if ( (inByte >= 'A') and (inByte <= 'H')) // Switch ON other triacs |
| { |
| digitalWrite(inByte-'A'+2, HIGH); |
| } |
| |
| pstatus(); // Print states |
| } |
| } |