| 1 |
# |
1 |
# |
| 2 |
# Makefile for usbasp |
2 |
# Makefile for usbasp |
| 3 |
# 20061119 Thomas Fischl original |
3 |
# 20061119 Thomas Fischl original |
| 4 |
# 20061120 Hanns-Konrad Unger help: and TARGET=atmega48 added |
4 |
# 20061120 Hanns-Konrad Unger help: and TARGET=atmega48 added |
| 5 |
# 20140209 Milan Horkel added automatic built for more targets |
5 |
# 20140209 Milan Horkel added automatic built for more targets |
| 6 |
|
6 |
|
| 7 |
ALL_TARGETS=atmega8 atmega88 |
7 |
ALL_TARGETS=atmega8 atmega88 |
| 8 |
|
8 |
|
| 9 |
# Default target |
9 |
# Default target |
| 10 |
# -------------- |
10 |
# -------------- |
| 11 |
|
11 |
|
| 12 |
ifndef $(TARGET) |
12 |
ifndef $(TARGET) |
| 13 |
TARGET=atmega88 |
13 |
TARGET=atmega88 |
| 14 |
endif |
14 |
endif |
| 15 |
|
15 |
|
| 16 |
|
16 |
|
| 17 |
# Define target dependent constants |
17 |
# Define target dependent constants |
| 18 |
# --------------------------------- |
18 |
# --------------------------------- |
| 19 |
|
19 |
|
| 20 |
ifeq ($(TARGET), atmega8) |
20 |
ifeq ($(TARGET), atmega8) |
| 21 |
HFUSE=0xC9 |
21 |
HFUSE=0xC9 |
| 22 |
LFUSE=0x9F |
22 |
LFUSE=0x9F |
| 23 |
endif |
23 |
endif |
| 24 |
|
24 |
|
| 25 |
ifeq ($(TARGET), atmega88) |
25 |
ifeq ($(TARGET), atmega88) |
| 26 |
EFUSE=0xF9 |
26 |
EFUSE=0xF9 |
| 27 |
HFUSE=0xDE |
27 |
HFUSE=0xDE |
| 28 |
LFUSE=0xD7 |
28 |
LFUSE=0xD7 |
| 29 |
endif |
29 |
endif |
| 30 |
|
30 |
|
| 31 |
|
31 |
|
| 32 |
# ISP=bsd PORT=/dev/parport0 |
32 |
# ISP=bsd PORT=/dev/parport0 |
| 33 |
# ISP=ponyser PORT=/dev/ttyS1 |
33 |
# ISP=ponyser PORT=/dev/ttyS1 |
| 34 |
# ISP=stk500 PORT=/dev/ttyS1 |
34 |
# ISP=stk500 PORT=/dev/ttyS1 |
| 35 |
# ISP=usbasp PORT=/dev/usb/ttyUSB0 |
35 |
# ISP=usbasp PORT=/dev/usb/ttyUSB0 |
| 36 |
# ISP=stk500v2 PORT=/dev/ttyUSB0 |
36 |
# ISP=stk500v2 PORT=/dev/ttyUSB0 |
| 37 |
ISP=usbasp |
37 |
ISP=usbasp |
| 38 |
PORT=/dev/usb/ttyUSB0 |
38 |
PORT=/dev/usb/ttyUSB0 |
| 39 |
|
39 |
|
| 40 |
help: |
40 |
help: |
| 41 |
@echo "Usage: make same as make help" |
41 |
@echo "Usage: make same as make help" |
| 42 |
@echo " make help same as make" |
42 |
@echo " make help same as make" |
| 43 |
@echo " make all build HEX for all target CPUs" |
43 |
@echo " make all build HEX for all target CPUs" |
| 44 |
@echo " make hex create HEX for default target CPU" |
44 |
@echo " make hex create HEX for default target CPU" |
| 45 |
@echo " make clean remove redundant data" |
45 |
@echo " make clean remove redundant data" |
| 46 |
@echo " make disasm create listing" |
46 |
@echo " make disasm create listing" |
| 47 |
@echo " make flash upload HEX into flash (for default target CPU)" |
47 |
@echo " make flash upload HEX into flash (for default target CPU)" |
| 48 |
@echo " make fuses program fuses (for default target CPU)" |
48 |
@echo " make fuses program fuses (for default target CPU)" |
| 49 |
@echo " make avrdude test avrdude" |
49 |
@echo " make avrdude test avrdude" |
| 50 |
@echo "Current values:" |
50 |
@echo "Current values:" |
| 51 |
@echo " TARGET=${TARGET}" |
51 |
@echo " TARGET=${TARGET}" |
| 52 |
@echo " LFUSE=${LFUSE}" |
52 |
@echo " LFUSE=${LFUSE}" |
| 53 |
@echo " HFUSE=${HFUSE}" |
53 |
@echo " HFUSE=${HFUSE}" |
| 54 |
@echo " CLOCK=12000000" |
54 |
@echo " CLOCK=12000000" |
| 55 |
@echo " ISP=${ISP}" |
55 |
@echo " ISP=${ISP}" |
| 56 |
@echo " PORT=${PORT}" |
56 |
@echo " PORT=${PORT}" |
| 57 |
|
57 |
|
| 58 |
COMPILE = avr-gcc -Wall -O2 -Iusbdrv -I. -mmcu=$(TARGET) # -DDEBUG_LEVEL=2 |
58 |
COMPILE = avr-gcc -Wall -O2 -Iusbdrv -I. -mmcu=$(TARGET) # -DDEBUG_LEVEL=2 |
| 59 |
|
59 |
|
| 60 |
OBJECTS = usbdrv/usbdrv.o usbdrv/usbdrvasm.o usbdrv/oddebug.o isp.o clock.o tpi.o main.o |
60 |
OBJECTS = usbdrv/usbdrv.o usbdrv/usbdrvasm.o usbdrv/oddebug.o isp.o clock.o tpi.o main.o |
| 61 |
|
61 |
|
| 62 |
.c.o: |
62 |
.c.o: |
| 63 |
$(COMPILE) -c $< -o $@ |
63 |
$(COMPILE) -c $< -o $@ |
| 64 |
#-Wa,-ahlms=$<.lst |
64 |
#-Wa,-ahlms=$<.lst |
| 65 |
|
65 |
|
| 66 |
.S.o: |
66 |
.S.o: |
| 67 |
$(COMPILE) -x assembler-with-cpp -c $< -o $@ |
67 |
$(COMPILE) -x assembler-with-cpp -c $< -o $@ |
| 68 |
# "-x assembler-with-cpp" should not be necessary since this is the default |
68 |
# "-x assembler-with-cpp" should not be necessary since this is the default |
| 69 |
# file type for the .S (with capital S) extension. However, upper case |
69 |
# file type for the .S (with capital S) extension. However, upper case |
| 70 |
# characters are not always preserved on Windows. To ensure WinAVR |
70 |
# characters are not always preserved on Windows. To ensure WinAVR |
| 71 |
# compatibility define the file type manually. |
71 |
# compatibility define the file type manually. |
| 72 |
|
72 |
|
| 73 |
.c.s: |
73 |
.c.s: |
| 74 |
$(COMPILE) -S $< -o $@ |
74 |
$(COMPILE) -S $< -o $@ |
| 75 |
|
75 |
|
| 76 |
cleantmp: |
76 |
cleantmp: |
| 77 |
rm -f usbasp.lst usbasp.obj usbasp.cof usbasp.list usbasp.map usbasp.bin *.o main.s usbdrv/*.o |
77 |
rm -f usbasp.lst usbasp.obj usbasp.cof usbasp.list usbasp.map usbasp.bin *.o main.s usbdrv/*.o |
| 78 |
|
78 |
|
| 79 |
clean: cleantmp |
79 |
clean: cleantmp |
| 80 |
rm -f usbasp_$(TARGET).hex usbasp_$(TARGET).eep.hex |
80 |
rm -f usbasp_$(TARGET).hex usbasp_$(TARGET).eep.hex |
| 81 |
|
81 |
|
| 82 |
# file targets: |
82 |
# file targets: |
| 83 |
usbasp.bin: $(OBJECTS) |
83 |
usbasp.bin: $(OBJECTS) |
| 84 |
$(COMPILE) -o usbasp.bin $(OBJECTS) -Wl,-Map,usbasp.map |
84 |
$(COMPILE) -o usbasp.bin $(OBJECTS) -Wl,-Map,usbasp.map |
| 85 |
|
85 |
|
| 86 |
usbasp.hex: usbasp_$(TARGET).hex |
86 |
usbasp.hex: usbasp_$(TARGET).hex |
| 87 |
|
87 |
|
| 88 |
usbasp_$(TARGET).hex: usbasp.bin |
88 |
usbasp_$(TARGET).hex: usbasp.bin |
| 89 |
rm -f usbasp_$(TARGET).hex usbasp_$(TARGET).eep.hex |
89 |
rm -f usbasp_$(TARGET).hex usbasp_$(TARGET).eep.hex |
| 90 |
avr-objcopy -j .text -j .data -O ihex usbasp.bin $@ |
90 |
avr-objcopy -j .text -j .data -O ihex usbasp.bin $@ |
| 91 |
# ./checksize usbasp.bin |
91 |
# ./checksize usbasp.bin |
| 92 |
# do the checksize script as our last action to allow successful compilation |
92 |
# do the checksize script as our last action to allow successful compilation |
| 93 |
# on Windows with WinAVR where the Unix commands will fail. |
93 |
# on Windows with WinAVR where the Unix commands will fail. |
| 94 |
|
94 |
|
| 95 |
disasm: usbasp.bin |
95 |
disasm: usbasp.bin |
| 96 |
avr-objdump -d usbasp.bin |
96 |
avr-objdump -d usbasp.bin |
| 97 |
|
97 |
|
| 98 |
cpp: |
98 |
cpp: |
| 99 |
$(COMPILE) -E main.c |
99 |
$(COMPILE) -E main.c |
| 100 |
|
100 |
|
| 101 |
flash: |
101 |
flash: |
| 102 |
avrdude -c ${ISP} -p ${TARGET} -P ${PORT} -U flash:w:usbasp.hex |
102 |
avrdude -c ${ISP} -p ${TARGET} -P ${PORT} -U flash:w:usbasp.hex |
| 103 |
|
103 |
|
| 104 |
fuses: |
104 |
fuses: |
| 105 |
avrdude -c ${ISP} -p ${TARGET} -P ${PORT} -u -U hfuse:w:$(HFUSE):m -U lfuse:w:$(LFUSE):m |
105 |
avrdude -c ${ISP} -p ${TARGET} -P ${PORT} -u -U hfuse:w:$(HFUSE):m -U lfuse:w:$(LFUSE):m |
| 106 |
|
106 |
|
| 107 |
avrdude: |
107 |
avrdude: |
| 108 |
avrdude -c ${ISP} -p ${TARGET} -P ${PORT} -v |
108 |
avrdude -c ${ISP} -p ${TARGET} -P ${PORT} -v |
| 109 |
|
109 |
|
| 110 |
# Fuse atmega8 |
110 |
# Fuse atmega8 |
| 111 |
# ------------ |
111 |
# ------------ |
| 112 |
# Fuse atmega8 high byte HFUSE: |
112 |
# Fuse atmega8 high byte HFUSE: |
| 113 |
# 0xD9 = 1 1 0 1 1 0 0 1 = Factory Default Value |
113 |
# 0xD9 = 1 1 0 1 1 0 0 1 = Factory Default Value |
| 114 |
# 0xC9 = 1 1 0 0 1 0 0 1 <-- BOOTRST (boot reset vector at 0x0000) |
114 |
# 0xC9 = 1 1 0 0 1 0 0 1 <-- BOOTRST (boot reset vector at 0x0000) |
| 115 |
# ^ ^ ^ ^ ^ ^ ^------ BOOTSZ0 |
115 |
# ^ ^ ^ ^ ^ ^ ^------ BOOTSZ0 |
| 116 |
# | | | | | +-------- BOOTSZ1 |
116 |
# | | | | | +-------- BOOTSZ1 |
| 117 |
# | | | | + --------- EESAVE (don't preserve EEPROM over chip erase) |
117 |
# | | | | + --------- EESAVE (don't preserve EEPROM over chip erase) |
| 118 |
# | | | +-------------- CKOPT (full output swing) |
118 |
# | | | +-------------- CKOPT (full output swing) |
| 119 |
# | | +---------------- SPIEN (allow serial programming) |
119 |
# | | +---------------- SPIEN (allow serial programming) |
| 120 |
# | +------------------ WDTON (WDT not always on) |
120 |
# | +------------------ WDTON (WDT not always on) |
| 121 |
# +-------------------- RSTDISBL (reset pin is enabled) |
121 |
# +-------------------- RSTDISBL (reset pin is enabled) |
| 122 |
# Fuse atmega8 low byte LFUSE: |
122 |
# Fuse atmega8 low byte LFUSE: |
| 123 |
# 0xE1 = 1 1 1 0 0 0 0 1 = Factory Default Value |
123 |
# 0xE1 = 1 1 1 0 0 0 0 1 = Factory Default Value |
| 124 |
# 0x9F = 1 0 0 1 1 1 1 1 |
124 |
# 0x9F = 1 0 0 1 1 1 1 1 |
| 125 |
# ^ ^ \ / \--+--/ |
125 |
# ^ ^ \ / \--+--/ |
| 126 |
# | | | +------- CKSEL 3..0 (external >8M crystal) |
126 |
# | | | +------- CKSEL 3..0 (external >8M crystal) |
| 127 |
# | | +--------------- SUT 1..0 (crystal osc, BOD enabled) |
127 |
# | | +--------------- SUT 1..0 (crystal osc, BOD enabled) |
| 128 |
# | +------------------ BODEN (BrownOut Detector enabled) |
128 |
# | +------------------ BODEN (BrownOut Detector enabled) |
| 129 |
# +-------------------- BODLEVEL (2.7V) |
129 |
# +-------------------- BODLEVEL (2.7V) |
| 130 |
# |
130 |
# |
| 131 |
# Fuse atmega88 |
131 |
# Fuse atmega88 |
| 132 |
# ------------- |
132 |
# ------------- |
| 133 |
# Fuse atmega88 extended byte: |
133 |
# Fuse atmega88 extended byte: |
| 134 |
# 0xF9 = 1 1 1 1 1 0 0 1 = Factory Default Value (default value is used) |
134 |
# 0xF9 = 1 1 1 1 1 0 0 1 = Factory Default Value (default value is used) |
| 135 |
# 0xF9 = 1 1 1 1 1 0 0 1 <-- BOOTRST (select vetor) |
135 |
# 0xF9 = 1 1 1 1 1 0 0 1 <-- BOOTRST (select vetor) |
| 136 |
# \+/ |
136 |
# \+/ |
| 137 |
# +----- BOOTSZ1..0 (Select Boot Size) |
137 |
# +----- BOOTSZ1..0 (Select Boot Size) |
| 138 |
# Fuse high byte: |
138 |
# Fuse high byte: |
| 139 |
# 0xDF 1 1 0 1 1 1 1 1 = Factory Default Value (default value may be used) |
139 |
# 0xDF 1 1 0 1 1 1 1 1 = Factory Default Value (default value may be used) |
| 140 |
# 0xDE = 1 1 0 1 1 1 1 0 |
140 |
# 0xDE = 1 1 0 1 1 1 1 0 |
| 141 |
# ^ ^ ^ ^ ^ \-+-/ |
141 |
# ^ ^ ^ ^ ^ \-+-/ |
| 142 |
# | | | | | +------ BODLEVEL (1.7-2.0V) |
142 |
# | | | | | +------ BODLEVEL (1.7-2.0V) |
| 143 |
# | | | | +---------- EESAVE (don't preserve EEPROM over chip erase) |
143 |
# | | | | +---------- EESAVE (don't preserve EEPROM over chip erase) |
| 144 |
# | | | +-------------- WDTON (WDT not always on) |
144 |
# | | | +-------------- WDTON (WDT not always on) |
| 145 |
# | | +---------------- SPIEN (allow serial programming)!!! |
145 |
# | | +---------------- SPIEN (allow serial programming)!!! |
| 146 |
# | +------------------ DWEN (debug wire not enabled) |
146 |
# | +------------------ DWEN (debug wire not enabled) |
| 147 |
# +-------------------- RSTDISBL (reset pin is not disabled) |
147 |
# +-------------------- RSTDISBL (reset pin is not disabled) |
| 148 |
# Fuse low byte: |
148 |
# Fuse low byte: |
| 149 |
# 0x62 0 1 1 0 0 0 1 0 = Factory Default Value (must be programmed to use xosc) |
149 |
# 0x62 0 1 1 0 0 0 1 0 = Factory Default Value (must be programmed to use xosc) |
| 150 |
# 0xD7 = 1 1 0 1 0 1 1 1 |
150 |
# 0xD7 = 1 1 0 1 0 1 1 1 |
| 151 |
# ^ ^ \ / \--+--/ |
151 |
# ^ ^ \ / \--+--/ |
| 152 |
# | | | +------- CKSEL 3..0 (full swing xosc, BOD enabled) |
152 |
# | | | +------- CKSEL 3..0 (full swing xosc, BOD enabled) |
| 153 |
# | | +--------------- SUT 1..0 (startup timer - see CKSEL) |
153 |
# | | +--------------- SUT 1..0 (startup timer - see CKSEL) |
| 154 |
# | +------------------ CKOUT (clock output is not enabled) |
154 |
# | +------------------ CKOUT (clock output is not enabled) |
| 155 |
# +-------------------- CLKDIV8 (clock divider is not enabled) |
155 |
# +-------------------- CLKDIV8 (clock divider is not enabled) |
| 156 |
|
156 |
|
| 157 |
|
157 |
|
| 158 |
|
158 |
|
| 159 |
SERIAL = `echo /dev/tty.USA19QI*` |
159 |
SERIAL = `echo /dev/tty.USA19QI*` |
| 160 |
UISP = uisp -dprog=$S -dserial=$(SERIAL) -dpart=auto |
160 |
UISP = uisp -dprog=$S -dserial=$(SERIAL) -dpart=auto |
| 161 |
# The two lines above are for "uisp" and the AVR910 serial programmer connected |
161 |
# The two lines above are for "uisp" and the AVR910 serial programmer connected |
| 162 |
# to a Keyspan USB to serial converter to a Mac running Mac OS X. |
162 |
# to a Keyspan USB to serial converter to a Mac running Mac OS X. |
| 163 |
# Choose your favorite programmer and interface. |
163 |
# Choose your favorite programmer and interface. |
| 164 |
|
164 |
|
| 165 |
uisp: all |
165 |
uisp: all |
| 166 |
$(UISP) --erase |
166 |
$(UISP) --erase |
| 167 |
$(UISP) --upload --verify if=usbasp_$(TARGET).hex |
167 |
$(UISP) --upload --verify if=usbasp_$(TARGET).hex |
| 168 |
|
168 |
|
| 169 |
# Execute these steps for each target CPU |
169 |
# Execute these steps for each target CPU |
| 170 |
# Do not remove empty line in this definition! |
170 |
# Do not remove empty line in this definition! |
| 171 |
define EXEC |
171 |
define EXEC |
| 172 |
rm -f usbasp_$(1).hex |
172 |
rm -f usbasp_$(1).hex |
| 173 |
make TARGET=$(1) cleantmp |
173 |
make TARGET=$(1) cleantmp |
| 174 |
make TARGET=$(1) usbasp_$(1).hex |
174 |
make TARGET=$(1) usbasp_$(1).hex |
| 175 |
|
175 |
|
| 176 |
endef |
176 |
endef |
| 177 |
|
177 |
|
| 178 |
ALL: |
178 |
all: |
| 179 |
@$(foreach III,$(ALL_TARGETS),$(call EXEC,$(III))) |
179 |
@$(foreach III,$(ALL_TARGETS),$(call EXEC,$(III))) |
| 180 |
@make cleantmp |
180 |
@make cleantmp |