Rev 4476 Rev 4491
1 $fn=40; // model faces resolution. 1 $fn=40; // model faces resolution.
2 include <../configuration.scad> 2 include <../configuration.scad>
3   3  
4 include <WINDGAUGE02A_D02.scad> 4 include <WINDGAUGE02A_D02.scad>
5 include <polyScrewThread_r1.scad> 5 include <polyScrewThread_r1.scad>
6   6  
7 PI=3.141592; 7 PI=3.141592;
8   8  
9   9  
10   10  
11 module WINDGAUGE02A_D01() 11 module WINDGAUGE02A_D01()
12 { 12 {
13   13  
14 difference() 14 difference()
15 { 15 {
16   16  
17 union() 17 union()
18 { 18 {
19 //zavit 19 //zavit
20 translate([0,0,D01_material_pod_zavitem]) 20 translate([0,0,D01_material_pod_zavitem])
21 screw_thread(S01_prumer_vnitrni-S01_tolerance_zavit,4,55,S01_vyska_spodniho_zavitu,PI/2,2); 21 screw_thread(S01_prumer_vnitrni-S01_tolerance_zavit,4,55,S01_vyska_spodniho_zavitu,PI/2,2);
22   22  
23 //spodní valec 23 //spodní valec
24 translate([0,0,D01_material_pod_zavitem/2]) 24 translate([0,0,D01_material_pod_zavitem/2])
25 cylinder (h = D01_material_pod_zavitem, r=(S01_prumer_vnitrni-S01_tolerance_zavit+D01_material_pred_zavitem*2)/2, center = true, $fn=100); 25 cylinder (h = D01_material_pod_zavitem, r=(S01_prumer_vnitrni-S01_tolerance_zavit+D01_material_pred_zavitem*2)/2, center = true, $fn=100);
26   26  
27 //uchyt na tyc 27 //uchyt na tyc
28 translate([0,D01_delka_tyce/2+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) 28 translate([0,D01_delka_tyce/2+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2])
29 cube([D01_sirka_tyce,D01_delka_tyce,D01_material_pod_zavitem],center=true); 29 cube([D01_sirka_tyce,D01_delka_tyce,D01_material_pod_zavitem],center=true);
-   30
-   31  
-   32
-   33  
-   34
-   35
-   36
-   37
30 //uchyt na tyc ovalna cast 38 //uchyt na tyc ovalna cast
31 translate([0,(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2]) 39 translate([0,(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem,D01_material_pod_zavitem/2])
32 cube([D01_sirka_tyce,D01_material_za_zavitem+D01_material_pred_zavitem,D01_material_pod_zavitem],center=true); 40 cube([D01_sirka_tyce,D01_material_za_zavitem+D01_material_pred_zavitem,D01_material_pod_zavitem],center=true);
33 41
34 42
35 //material kolem uchytu na sloupek 43 //material kolem uchytu na sloupek
36 translate([0,D01_delka_tyce+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem+(D02_sila_materialu+D02_prumer_obruby/2)/2-D02_dotahova_vzdalenost,D01_material_pod_zavitem/2]) 44 translate([0,D01_delka_tyce+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem+(D02_sila_materialu+D02_prumer_obruby/2)/2-D02_dotahova_vzdalenost,D01_material_pod_zavitem/2])
37 difference() 45 difference()
38 { 46 {
39 cube([D01_sirka_tyce,D02_sila_materialu+D02_prumer_obruby/2,D01_material_pod_zavitem],center=true); 47 cube([D01_sirka_tyce,D02_sila_materialu+D02_prumer_obruby/2,D01_material_pod_zavitem],center=true);
40 translate([0,D02_prumer_obruby/2-D02_dotahova_vzdalenost-D02_sila_materialu,0]) 48 translate([0,D02_prumer_obruby/2-D02_dotahova_vzdalenost-D02_sila_materialu,0])
41 cylinder(h=D02_vyska_uchytky+0.01,r=D02_prumer_obruby/2,center=true); 49 cylinder(h=D02_vyska_uchytky+0.01,r=D02_prumer_obruby/2,center=true);
42 50
43 } 51 }
44 52
45   53  
46   54  
47 //uchyt na sloupek 55 //uchyt na sloupek
48 56
49 translate([0,D01_delka_tyce+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem+D02_sila_materialu+(D02_prumer_obruby)/2,D02_vyska_uchytky/2]) 57 translate([0,D01_delka_tyce+(S01_prumer_vnitrni-S01_tolerance_zavit)/2+D01_material_pred_zavitem+D02_sila_materialu+(D02_prumer_obruby)/2,D02_vyska_uchytky/2])
50 rotate(a=[0,0,270]) 58 rotate(a=[0,0,270])
51 WINDGAUGE02A_D02(); 59 WINDGAUGE02A_D02();
52   60  
53 } 61 }
54   62  
55 //otvor 63 //otvor
56 translate([0,0,(D01_material_pod_zavitem+S01_vyska_spodniho_zavitu)/2]) 64 translate([0,0,(D01_material_pod_zavitem+S01_vyska_spodniho_zavitu)/2])
57 cylinder (h = D01_material_pod_zavitem+S01_vyska_spodniho_zavitu+0.02, r=((S01_prumer_vnitrni-S01_tolerance_zavit)-2*D01_material_za_zavitem)/2, center = true, $fn=100); 65 cylinder (h = D01_material_pod_zavitem+S01_vyska_spodniho_zavitu+0.02, r=((S01_prumer_vnitrni-S01_tolerance_zavit)-2*D01_material_za_zavitem)/2, center = true, $fn=100);
58   66  
59 } 67 }
60 } 68 }
61 69
62 WINDGAUGE02A_D01(); 70 WINDGAUGE02A_D01();
63   71  
64   72  
65 73
66 74