| Line 9... |
Line 9... |
| 9 |
#define LCD_DATA7 PIN_D7 |
9 |
#define LCD_DATA7 PIN_D7 |
| 10 |
#include <lcd.c> |
10 |
#include <lcd.c> |
| 11 |
|
11 |
|
| 12 |
#include "../SHT25.h" |
12 |
#include "../SHT25.h" |
| 13 |
#include "../LTS01.h" |
13 |
#include "../LTS01.h" |
| - |
|
14 |
#include "./HMC5883L.h" |
| - |
|
15 |
#include <math.h> |
| - |
|
16 |
|
| 14 |
|
17 |
|
| 15 |
void main() |
18 |
void main() |
| 16 |
{ |
19 |
{ |
| 17 |
float temp1, temp2, humidity; |
20 |
float temp1, temp2, humidity; |
| 18 |
int16 i=0; |
21 |
int16 i=0; |
| Line 26... |
Line 29... |
| 26 |
setup_ccp1(CCP_OFF); |
29 |
setup_ccp1(CCP_OFF); |
| 27 |
setup_comparator(NC_NC_NC_NC); // This device COMP currently not supported by the PICWizard |
30 |
setup_comparator(NC_NC_NC_NC); // This device COMP currently not supported by the PICWizard |
| 28 |
setup_oscillator(OSC_8MHZ); |
31 |
setup_oscillator(OSC_8MHZ); |
| 29 |
|
32 |
|
| 30 |
|
33 |
|
| 31 |
printf("GeoMet01A\r\n",); |
34 |
printf("GeoMet01A\r\n"); |
| 32 |
printf("(c) Kaklik 2013\r\n"); |
35 |
printf("(c) Kaklik 2013\r\n"); |
| 33 |
printf("www.mlab.cz\r\n"); |
36 |
printf("www.mlab.cz\r\n"); |
| 34 |
|
37 |
|
| - |
|
38 |
// Init the HMC5883L. Set Mode register for |
| - |
|
39 |
// continuous measurements. |
| - |
|
40 |
hmc5883l_write_reg(HMC5883L_CFG_A_REG, 0x18); // no average, maximal update range |
| - |
|
41 |
hmc5883l_write_reg(HMC5883L_CFG_B_REG, 0x00); // minimal range |
| - |
|
42 |
hmc5883l_write_reg(HMC5883L_MODE_REG, 0x00); |
| - |
|
43 |
|
| 35 |
lcd_init(); |
44 |
lcd_init(); |
| 36 |
lcd_putc("(c) Kaklik 2013"); |
45 |
lcd_putc("(c) Kaklik 2013"); |
| 37 |
lcd_gotoxy(3,2); |
46 |
lcd_gotoxy(3,2); |
| 38 |
lcd_putc("www.mlab.cz"); |
47 |
lcd_putc("www.mlab.cz"); |
| 39 |
Delay_ms(2000); |
48 |
Delay_ms(2000); |
| Line 43... |
Line 52... |
| 43 |
{ |
52 |
{ |
| 44 |
lcd_gotoxy(1,1); |
53 |
lcd_gotoxy(1,1); |
| 45 |
temp1 = SHT25_get_temp(); |
54 |
temp1 = SHT25_get_temp(); |
| 46 |
humidity = SHT25_get_hum(); |
55 |
humidity = SHT25_get_hum(); |
| 47 |
temp2= LTS01_get_temp(); |
56 |
temp2= LTS01_get_temp(); |
| - |
|
57 |
hmc5883l_read_data(); |
| 48 |
|
58 |
|
| 49 |
printf(lcd_putc,"%f C %f \%% \r\n",temp1, humidity); |
59 |
printf(lcd_putc,"%f C %f \%%",temp1, humidity); |
| 50 |
lcd_gotoxy(1,2); |
60 |
lcd_gotoxy(1,2); |
| 51 |
printf(lcd_putc," %f C",temp2); |
61 |
printf(lcd_putc," %f C",temp2); |
| 52 |
printf("%ld %f %f %f \r\n",i, temp1, humidity, temp2); |
62 |
printf("%ld %f %f %f ",i, temp1, humidity, temp2); |
| - |
|
63 |
printf("%Ld %Ld %Ld \n\r", compass.x, compass.y, compass.z); |
| 53 |
i++; |
64 |
i++; |
| 54 |
Delay_ms(100); |
65 |
Delay_ms(100); |
| 55 |
} |
66 |
} |
| 56 |
|
67 |
|
| 57 |
} |
68 |
} |