Rev 4708 Rev 4730
Line 1... Line 1...
1 # generated by Slic3r 1.3.0-dev on 2016-08-30 20:09:48 1 # generated by Slic3r 1.3.0-dev on 2016-09-02 05:15:44
2 avoid_crossing_perimeters = 1 2 avoid_crossing_perimeters = 1
3 bed_shape = 0x0,180x0,180x180,0x180 3 bed_shape = 0x0,180x0,180x180,0x180
4 bed_temperature = 50 4 bed_temperature = 50
5 before_layer_gcode = 5 before_layer_gcode =
6 bottom_solid_layers = 3 6 bottom_solid_layers = 5
7 bridge_acceleration = 1000 7 bridge_acceleration = 1000
8 bridge_fan_speed = 100 8 bridge_fan_speed = 100
9 bridge_flow_ratio = 1 9 bridge_flow_ratio = 1
10 bridge_speed = 5 10 bridge_speed = 5
11 brim_width = 0 11 brim_width = 0
Line 38... Line 38...
38 first_layer_acceleration = 500 38 first_layer_acceleration = 500
39 first_layer_bed_temperature = 60 39 first_layer_bed_temperature = 60
40 first_layer_extrusion_width = 180% 40 first_layer_extrusion_width = 180%
41 first_layer_height = 0.3 41 first_layer_height = 0.3
42 first_layer_speed = 60% 42 first_layer_speed = 60%
43 first_layer_temperature = 220 43 first_layer_temperature = 215
44 gap_fill_speed = 10 44 gap_fill_speed = 10
45 gcode_arcs = 0 45 gcode_arcs = 0
46 gcode_comments = 0 46 gcode_comments = 0
47 gcode_flavor = reprap 47 gcode_flavor = reprap
48 infill_acceleration = 500 48 infill_acceleration = 500
Line 50... Line 50...
50 infill_extruder = 1 50 infill_extruder = 1
51 infill_extrusion_width = 0 51 infill_extrusion_width = 0
52 infill_first = 0 52 infill_first = 0
53 infill_only_where_needed = 0 53 infill_only_where_needed = 0
54 infill_overlap = 15% 54 infill_overlap = 15%
55 infill_speed = 60 55 infill_speed = 50
56 interface_shells = 0 56 interface_shells = 0
57 layer_gcode = 57 layer_gcode =
58 layer_height = 0.15 58 layer_height = 0.15
59 max_fan_speed = 100 59 max_fan_speed = 100
60 max_print_speed = 80 60 max_print_speed = 80
61 max_volumetric_speed = 0 61 max_volumetric_speed = 5
62 min_fan_speed = 100 62 min_fan_speed = 100
63 min_print_speed = 10 63 min_print_speed = 10
64 min_skirt_length = 0 64 min_skirt_length = 20
65 notes = 65 notes =
66 nozzle_diameter = 0.4 66 nozzle_diameter = 0.4
67 octoprint_apikey = A7268185315B4A8B9CA2C16415AC5F1F 67 octoprint_apikey = A7268185315B4A8B9CA2C16415AC5F1F
68 octoprint_host = 192.168.1.12:80 68 octoprint_host = 192.168.1.12:80
69 only_retract_when_crossing_perimeters = 1 69 only_retract_when_crossing_perimeters = 1
Line 101... Line 101...
101 small_perimeter_speed = 30 101 small_perimeter_speed = 30
102 solid_infill_below_area = 70 102 solid_infill_below_area = 70
103 solid_infill_every_layers = 0 103 solid_infill_every_layers = 0
104 solid_infill_extruder = 1 104 solid_infill_extruder = 1
105 solid_infill_extrusion_width = 0 105 solid_infill_extrusion_width = 0
106 solid_infill_speed = 55 106 solid_infill_speed = 50
107 spiral_vase = 0 107 spiral_vase = 0
108 standby_temperature_delta = -5 108 standby_temperature_delta = -5
109 start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder 109 start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
110 support_material = 0 110 support_material = 0
111 support_material_angle = 0 111 support_material_angle = 0
Line 119... Line 119...
119 support_material_interface_speed = 100% 119 support_material_interface_speed = 100%
120 support_material_pattern = rectilinear 120 support_material_pattern = rectilinear
121 support_material_spacing = 2.5 121 support_material_spacing = 2.5
122 support_material_speed = 60 122 support_material_speed = 60
123 support_material_threshold = 0 123 support_material_threshold = 0
124 temperature = 220 124 temperature = 215
125 thin_walls = 1 125 thin_walls = 1
126 threads = 4 126 threads = 4
127 toolchange_gcode = 127 toolchange_gcode =
128 top_infill_extrusion_width = 0 128 top_infill_extrusion_width = 0
129 top_solid_infill_speed = 50 129 top_solid_infill_speed = 50
130 top_solid_layers = 3 130 top_solid_layers = 5
131 travel_speed = 130 131 travel_speed = 130
132 use_firmware_retraction = 0 132 use_firmware_retraction = 0
133 use_relative_e_distances = 1 133 use_relative_e_distances = 1
134 use_volumetric_e = 0 134 use_volumetric_e = 0
135 vibration_limit = 0 135 vibration_limit = 0