| Line 33... |
Line 33... |
| 33 |
//spodní valec |
33 |
//spodní valec |
| 34 |
translate([0,0,D01_material_pod_zavitem/2]) |
34 |
translate([0,0,D01_material_pod_zavitem/2]) |
| 35 |
cylinder (h = D01_material_pod_zavitem, r=(S01_prumer_zavitu+D01_material_pred_zavitem*2)/2, center = true, $fn=100); |
35 |
cylinder (h = D01_material_pod_zavitem, r=(S01_prumer_zavitu+D01_material_pred_zavitem*2)/2, center = true, $fn=100); |
| 36 |
|
36 |
|
| 37 |
translate([0,0,-4]) |
37 |
translate([0,0,-4]) |
| 38 |
screw_thread(S01_prumer_zavitu-D01_material_za_zavitem,4,55,D01_material_pod_zavitem+8,PI/2,2); |
38 |
screw_thread(S01_prumer_zavitu-2*D01_material_za_zavitem-2*D03_tolerance_zavitu,4,55,D01_material_pod_zavitem+4,PI/2,2); |
| 39 |
|
39 |
|
| 40 |
|
40 |
|
| 41 |
} |
41 |
} |
| 42 |
|
42 |
|
| 43 |
//uchyt na tyc |
43 |
//uchyt na tyc |
| Line 66... |
Line 66... |
| 66 |
rotate(a=[0,0,270]) |
66 |
rotate(a=[0,0,270]) |
| 67 |
AWSCREEN01A_D06_2(); |
67 |
AWSCREEN01A_D06_2(); |
| 68 |
|
68 |
|
| 69 |
} |
69 |
} |
| 70 |
|
70 |
|
| 71 |
//otvor |
71 |
//otvor válcový |
| 72 |
translate([0,0,D01_material_pod_zavitem-1+S01_vyska_komponentu_na_lozisko/2]) |
72 |
translate([0,0,D01_material_pod_zavitem-1+S01_vyska_komponentu_na_lozisko/2]) |
| 73 |
cylinder (h = S01_vyska_komponentu_na_lozisko+2+0.02, r=(S01_prumer_zavitu-2*D03_tolerance_zavitu-D01_material_za_zavitem)/2, center = true, $fn=100); |
73 |
cylinder (h = S01_vyska_komponentu_na_lozisko+2+0.02, r=(S01_prumer_zavitu-2*D03_tolerance_zavitu-2*D01_material_za_zavitem)/2, center = true, $fn=100); |
| 74 |
|
74 |
|
| 75 |
//odecet vrchního závitu aby byl rovný |
75 |
//odecet vrchního závitu aby byl rovný |
| 76 |
translate([0,0,D01_material_pod_zavitem+S01_vyska_komponentu_na_lozisko]) |
76 |
translate([0,0,D01_material_pod_zavitem+S01_vyska_komponentu_na_lozisko]) |
| 77 |
|
77 |
|
| 78 |
cylinder (h = S01_vyska_komponentu_na_lozisko+0.02, r=(S01_prumer_zavitu-2*D03_tolerance_zavitu)/2, $fn=100); |
78 |
cylinder (h = S01_vyska_komponentu_na_lozisko+0.02, r=(S01_prumer_zavitu-2*D03_tolerance_zavitu)/2, $fn=100); |
| - |
|
79 |
|
| - |
|
80 |
|
| - |
|
81 |
// cube([200,200,200]); |
| - |
|
82 |
|
| 79 |
} |
83 |
} |
| 80 |
} |
84 |
} |
| 81 |
|
85 |
|
| 82 |
AWSCREEN01A_D05(S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,D01_material_pod_zavitem,D01_material_za_zavitem,D01_material_pred_zavitem,D01_delka_tyce,D01_sirka_tyce,D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu,D03_tolerance_zavitu); |
86 |
AWSCREEN01A_D05(S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,D01_material_pod_zavitem,D01_material_za_zavitem,D01_material_pred_zavitem,D01_delka_tyce,D01_sirka_tyce,D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu,D03_tolerance_zavitu); |
| 83 |
|
87 |
|