Rev 4571 Rev 4578
Line 1... Line 1...
1 use <configuration/sloupek.scad> 1 use <configuration/sloupek.scad>
2 use <configuration/plbase.scad> 2 use <configuration/plbase.scad>
3 use <configuration/bocnice.scad> 3 use <configuration/bocnice.scad>
4 use <configuration/otvory.scad> 4 use <configuration/otvory.scad>
5 use <configuration/text/Write.scad> 5 use <configuration/text/Write.scad>
6 use <upravena_bocnice.scad> 6 use <upravena_bocnice.scad>
7   7  
8 include <configuration/manufactury_conf.scad> 8 include <configuration/manufactury_conf.scad>
9 include <configuration.scad> 9 include <configuration.scad>
10 include <configuration/otvory_conf.scad> 10 include <configuration/otvory_conf.scad>
11   11  
12   12  
13 barva_sloupku = "cyan"; 13 barva_sloupku = "cyan";
14 barva_listy = "red"; 14 barva_listy = "red";
15 barva_celicka = "green"; 15 barva_celicka = "green";
16 barva_plbase = "yellow"; 16 barva_plbase = "yellow";
17   17  
18 //translate([0.5*10.16,-5.08,14]) 18 //translate([0.5*10.16,-5.08,14])
19 // cube([10.16,10.16,10.16]); 19 // cube([10.16,10.16,10.16]);
20   20  
21   21  
22 //BOCNICE SE DNEM 22 //BOCNICE SE DNEM
23 //------------------------------------------------------------- 23 //-------------------------------------------------------------
24 upravena_bocnice(); 24 upravena_bocnice();
25   25  
26   26  
27   27  
28   28  
29   29  
30 //PLBASE HORNI 30 //PLBASE HORNI
31 //------------------------------------------------------------- 31 //-------------------------------------------------------------
32   32  
33   33  
34   34  
35 translate([plbase_tolerance_horni-0.2,+plbase_tolerance_horni-0.2,vyska_bocnice/2-tloustka_plbase/2]) 35 translate([plbase_tolerance_horni-0.2,+plbase_tolerance_horni-0.2,vyska_bocnice/2-tloustka_plbase/2])
36 rotate(a=[0,0,0]) 36 rotate(a=[0,0,0])
37 { 37 {
38 38
39 39
40 //plbase_vrchni_kryt(pocet_der1+2,pocet_der2+2,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,vyska_bocnice,prekryti_der,tloustka_bocnice,plbase_tolerance_horni); 40 //plbase_vrchni_kryt(pocet_der1+2,pocet_der2+2,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,vyska_bocnice,prekryti_der,tloustka_bocnice,plbase_tolerance_horni);
41 41
42 plbase_vrchni_kryt_pro_odecet(pocet_der1-1,pocet_der2-1,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,vyska_bocnice,prekryti_der,tloustka_bocnice,-0.2,tloustka_plbase); 42 plbase_vrchni_kryt_pro_odecet(pocet_der1-1,pocet_der2-1,radidus_hrany,vzdalenost_der,vzdalenost_od_okraje,prumer_sroubu,vyska_bocnice,prekryti_der,tloustka_bocnice,-0.2,tloustka_plbase);
43 } 43 }
44   44  
45   45  
46   46  
47   47  
48   48  
49   49  
50   50  
51   51  
52   52  
53   53