| Line 22... |
Line 22... |
| 22 |
linear_extrude (height = D03_tloustka_materialu, convexity = 10) |
22 |
linear_extrude (height = D03_tloustka_materialu, convexity = 10) |
| 23 |
polygon(points=[[D02_vyska_uchytky/2,D01_delka_tyce+S01_prumer_zavitu/2+D01_material_pred_zavitem+D02_sila_materialu],[0, D01_delka_tyce+S01_prumer_zavitu/2+D01_material_pred_zavitem+D02_sila_materialu],[0,D03_polomer_stitu+D01_material_pred_zavitem],[D01_material_pod_zavitem,D03_polomer_stitu+D01_material_pred_zavitem]]); |
23 |
polygon(points=[[D02_vyska_uchytky/2,D01_delka_tyce+S01_prumer_zavitu/2+D01_material_pred_zavitem+D02_sila_materialu],[0, D01_delka_tyce+S01_prumer_zavitu/2+D01_material_pred_zavitem+D02_sila_materialu],[0,D03_polomer_stitu+D01_material_pred_zavitem],[D01_material_pod_zavitem,D03_polomer_stitu+D01_material_pred_zavitem]]); |
| 24 |
|
24 |
|
| 25 |
|
25 |
|
| 26 |
//zavit |
26 |
//zavit |
| 27 |
translate([0,0,D01_material_pod_zavitem]) |
27 |
translate([0,0,D01_material_pod_zavitem-2]) |
| 28 |
screw_thread(S01_prumer_zavitu-2*D03_tolerance_zavitu,4,55,S01_vyska_komponentu_na_lozisko,PI/2,2); |
28 |
screw_thread(S01_prumer_zavitu-2*D03_tolerance_zavitu,4,55,S01_vyska_komponentu_na_lozisko+5,PI/2,2); |
| 29 |
|
29 |
|
| 30 |
|
30 |
|
| 31 |
difference() |
31 |
difference() |
| 32 |
{ |
32 |
{ |
| 33 |
//spodní valec |
33 |
//spodní valec |
| Line 62... |
Line 62... |
| 62 |
|
62 |
|
| 63 |
//uchyt na sloupek |
63 |
//uchyt na sloupek |
| 64 |
|
64 |
|
| 65 |
translate([0,D01_delka_tyce+S01_prumer_zavitu/2+D01_material_pred_zavitem+D02_sila_materialu+(D02_prumer_obruby)/2,D02_vyska_uchytky/2]) |
65 |
translate([0,D01_delka_tyce+S01_prumer_zavitu/2+D01_material_pred_zavitem+D02_sila_materialu+(D02_prumer_obruby)/2,D02_vyska_uchytky/2]) |
| 66 |
rotate(a=[0,0,270]) |
66 |
rotate(a=[0,0,270]) |
| 67 |
AWSCREEN01A_D06(D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu); |
67 |
AWSCREEN01A_D06_2(); |
| 68 |
|
68 |
|
| 69 |
} |
69 |
} |
| 70 |
|
70 |
|
| 71 |
//otvor |
71 |
//otvor |
| 72 |
translate([0,0,D01_material_pod_zavitem+S01_vyska_komponentu_na_lozisko/2]) |
72 |
translate([0,0,D01_material_pod_zavitem-1+S01_vyska_komponentu_na_lozisko/2]) |
| 73 |
cylinder (h = S01_vyska_komponentu_na_lozisko+0.02, r=(S01_prumer_zavitu-2*D03_tolerance_zavitu-D01_material_za_zavitem)/2, center = true, $fn=100); |
73 |
cylinder (h = S01_vyska_komponentu_na_lozisko+2+0.02, r=(S01_prumer_zavitu-2*D03_tolerance_zavitu-D01_material_za_zavitem)/2, center = true, $fn=100); |
| 74 |
|
- |
|
| 75 |
|
74 |
|
| - |
|
75 |
//odecet vrchního závitu aby byl rovný |
| - |
|
76 |
translate([0,0,D01_material_pod_zavitem+S01_vyska_komponentu_na_lozisko]) |
| 76 |
|
77 |
|
| - |
|
78 |
cylinder (h = S01_vyska_komponentu_na_lozisko+0.02, r=(S01_prumer_zavitu-2*D03_tolerance_zavitu)/2, $fn=100); |
| 77 |
} |
79 |
} |
| 78 |
} |
80 |
} |
| 79 |
|
81 |
|
| 80 |
AWSCREEN01A_D05(S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,D01_material_pod_zavitem,D01_material_za_zavitem,D01_material_pred_zavitem,D01_delka_tyce,D01_sirka_tyce,D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu,D03_tolerance_zavitu); |
82 |
AWSCREEN01A_D05(S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,D01_material_pod_zavitem,D01_material_za_zavitem,D01_material_pred_zavitem,D01_delka_tyce,D01_sirka_tyce,D02_sila_materialu,D02_vyska_uchytky,D02_prumer_obruby,D02_delka_celeho_uchytu,D02_dotahova_vzdalenost,D02_prumer_uchytneho_sroubu,D03_tolerance_zavitu); |
| 81 |
|
83 |
|