Rev 4288 Rev 4297
Line 2... Line 2...
2 //include <../configuration.scad> 2 //include <../configuration.scad>
3   3  
4   4  
5   5  
6 module stator1(stator1_sila,lozisko_prumer_vnejsi,sirka_matky,lozisko_prumer_vnitrni,lozisko_prekryv,prumer_sroubu) 6 module stator1(stator1_sila,lozisko_prumer_vnejsi,sirka_matky,lozisko_prumer_vnitrni,lozisko_prekryv,prumer_sroubu)
7 { 7 {
8 difference() 8 difference()
9 { 9 {
10 cylinder (h = stator1_sila, r=(lozisko_prumer_vnejsi+10+sirka_matky)/2, center = true, $fn=100); 10 cylinder (h = stator1_sila, r=(lozisko_prumer_vnejsi+10+sirka_matky)/2, center = true, $fn=100);
11 11
12   12  
13 //otvor pro hridel rotoru 13 //otvor pro hridel rotoru
14 translate([0,0,0]) 14 translate([0,0,0])
15 cylinder (h = stator1_sila+0.1, r=(lozisko_prumer_vnitrni+2*lozisko_prekryv+2)/2, center = true, $fn=100); 15 cylinder (h = stator1_sila+0.1, r=(lozisko_prumer_vnitrni+2*lozisko_prekryv+2)/2, center = true, $fn=100);
16 16
17 17
18 18
19 //otvor pro sroub 1 19 //otvor pro sroub 1
20 translate([(lozisko_prumer_vnejsi+prumer_sroubu+5)/2,0,0]) 20 translate([(lozisko_prumer_vnejsi+prumer_sroubu+5)/2,0,0])
21 cylinder (h = stator1_sila+0.1, r=prumer_sroubu/2, center = true, $fn=100); 21 cylinder (h = stator1_sila+0.1, r=prumer_sroubu/2, center = true, $fn=100);
22   22  
23 //otvor pro sroub 2 23 //otvor pro sroub 2
24 rotate(a=[0,0,120]) 24 rotate(a=[0,0,120])
25 translate([(lozisko_prumer_vnejsi+prumer_sroubu+5)/2,0,0]) 25 translate([(lozisko_prumer_vnejsi+prumer_sroubu+5)/2,0,0])
26   -  
27 cylinder (h = stator1_sila+0.1, r=prumer_sroubu/2, center = true, $fn=100); 26 cylinder (h = stator1_sila+0.1, r=prumer_sroubu/2, center = true, $fn=100);
28 -  
29 //otvor pro sroub 3 -  
30 rotate(a=[0,0,240]) -  
31 translate([(lozisko_prumer_vnejsi+prumer_sroubu+5)/2,0,0]) -  
32   -  
33 cylinder (h = stator1_sila+0.1, r=prumer_sroubu/2, center = true, $fn=100); -  
34 27
35   -  
36   -  
-   28 //otvor pro sroub 3
-   29 rotate(a=[0,0,240])
-   30 translate([(lozisko_prumer_vnejsi+prumer_sroubu+5)/2,0,0])
-   31 cylinder (h = stator1_sila+0.1, r=prumer_sroubu/2, center = true, $fn=100);
37 32 }
38   -  
39 } 33 }
40 } -  
41   34  
42   35  
43   36  
44   37  
45   38