| Line 54... |
Line 54... |
| 54 |
{ |
54 |
{ |
| 55 |
union() |
55 |
union() |
| 56 |
{ |
56 |
{ |
| 57 |
//závit na ukotvení rotoru |
57 |
//závit na ukotvení rotoru |
| 58 |
//zakladni material |
58 |
//zakladni material |
| 59 |
cylinder (h = (S01_prumer_vnitrni/2+4*S01_sila_materialu)+R01_vyska_preryti_statoru, r=(lozisko_prumer_vnejsi/2-1)+2, $fn=100); |
59 |
cylinder (h = (S01_prumer_vnitrni/2+4*S01_sila_materialu)+R01_vyska_preryti_statoru, r=(lozisko_prumer_vnejsi/2-1), $fn=100); |
| 60 |
|
60 |
|
| 61 |
vyztuhy(); |
61 |
vyztuhy(); |
| 62 |
} |
62 |
} |
| 63 |
|
63 |
|
| 64 |
//vnitrni zavit |
64 |
//vnitrni zavit |
| 65 |
translate([0,0,-5]) |
65 |
translate([0,0,-5]) |
| 66 |
screw_thread((15),3,55,R01_vyska_preryti_statoru+10,PI/2,2); |
66 |
screw_thread((12),3,55,R01_vyska_preryti_statoru+10,PI/2,2); |
| 67 |
|
67 |
|
| 68 |
//za závitem aby to slo tisknout |
68 |
//za závitem aby to slo tisknout |
| 69 |
translate([0,0,R01_vyska_preryti_statoru+5]) |
69 |
translate([0,0,R01_vyska_preryti_statoru+5]) |
| 70 |
cylinder(h=(5), r1=(15)/2, r2=0, center=false, $fn=100); |
70 |
cylinder(h=(5), r1=(12)/2, r2=0, center=false, $fn=100); |
| 71 |
|
71 |
|
| 72 |
difference() |
72 |
difference() |
| 73 |
{ |
73 |
{ |
| 74 |
translate([0,0,R01_vyska_preryti_statoru]) |
74 |
translate([0,0,R01_vyska_preryti_statoru]) |
| 75 |
sphere(d = (S01_prumer_vnitrni/2+5*S01_sila_materialu)*2+10, $fn=100); |
75 |
sphere(d = (S01_prumer_vnitrni/2+5*S01_sila_materialu)*2+10, $fn=100); |
| Line 129... |
Line 129... |
| 129 |
translate([-L01_hrana_drzaku_a,0,0]) |
129 |
translate([-L01_hrana_drzaku_a,0,0]) |
| 130 |
cube([L01_hrana_drzaku_a,L01_delka_uchytu+L01_prumer_lopatky/2+10,L01_hrana_drzaku_b],center=false); |
130 |
cube([L01_hrana_drzaku_a,L01_delka_uchytu+L01_prumer_lopatky/2+10,L01_hrana_drzaku_b],center=false); |
| 131 |
|
131 |
|
| 132 |
//podpěra |
132 |
//podpěra |
| 133 |
translate([0,0,0]) |
133 |
translate([0,0,0]) |
| 134 |
cylinder(h=(L01_prumer_lopatky/2), r1=L01_prumer_lopatky/3.5, r2=L01_prumer_lopatky/2, center=false, $fn=100); |
134 |
cylinder(h=(L01_prumer_lopatky/2), r1=(L01_prumer_lopatky)/3.5, r2=(L01_prumer_lopatky-1)/2, center=false, $fn=100); |
| 135 |
|
135 |
|
| 136 |
} |
136 |
} |
| 137 |
|
137 |
|
| 138 |
|
138 |
|
| 139 |
translate([0,0,L01_prumer_lopatky/2]) |
139 |
translate([0,0,L01_prumer_lopatky/2]) |