| Line 1... |
Line 1... |
| 1 |
$fn=40; // model faces resolution. |
1 |
$fn=40; // model faces resolution. |
| 2 |
include <../configuration.scad> |
2 |
include <../configuration.scad> |
| 3 |
|
3 |
|
| 4 |
use <zavity.scad> |
- |
|
| 5 |
include <polyScrewThread_r1.scad> |
4 |
include <polyScrewThread_r1.scad> |
| 6 |
|
5 |
|
| 7 |
PI=3.141592; |
6 |
PI=3.141592; |
| 8 |
|
7 |
|
| 9 |
module WINDGAUGE02A_S03(S01_sila_materialu,S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,lozisko_vyska,lozisko_prumer_vnejsi,lozisko_prumer_vnitrni,lozisko_prekryv,vyska_matky,prumer_orechu,prumer_sroubu,vyska_hlavy_sroubu,prumer_hlavy_sroubu,S01_tolerance_zavit,R02_vzdalenost_mezi_uchyty_lopatek,L01_sila_zapusteni_drzaku,L01_hloubka_zapusteni,vule_mezi_statorem_rotorem,S01_sila_materialu,S01_hloubka_zavitu) |
8 |
module WINDGAUGE02A_S03(S01_sila_materialu,S01_vyska_komponentu_na_lozisko,S01_prumer_zavitu,lozisko_vyska,lozisko_prumer_vnejsi,lozisko_prumer_vnitrni,lozisko_prekryv,vyska_matky,prumer_orechu,prumer_sroubu,vyska_hlavy_sroubu,prumer_hlavy_sroubu,S01_tolerance_zavit,R02_vzdalenost_mezi_uchyty_lopatek,L01_sila_zapusteni_drzaku,L01_hloubka_zapusteni,vule_mezi_statorem_rotorem,S01_sila_materialu,S01_hloubka_zavitu) |
| Line 12... |
Line 11... |
| 12 |
{ |
11 |
{ |
| 13 |
//valec se zavitem |
12 |
//valec se zavitem |
| 14 |
difference() |
13 |
difference() |
| 15 |
{ |
14 |
{ |
| 16 |
|
15 |
|
| 17 |
screw_thread((R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem+2*S01_sila_materialu)-S01_tolerance_zavit,S01_hloubka_zavitu,55,S01_vyska_komponentu_na_lozisko,PI/2,2); |
16 |
screw_thread((R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem)-S01_tolerance_zavit,S01_hloubka_zavitu,55,S01_vyska_komponentu_na_lozisko,PI/2,2); |
| 18 |
|
17 |
|
| 19 |
translate([0,0,S01_sila_materialu+S01_vyska_komponentu_na_lozisko/2]) |
18 |
translate([0,0,S01_sila_materialu+S01_vyska_komponentu_na_lozisko/2]) |
| 20 |
cylinder (h = S01_vyska_komponentu_na_lozisko+0.01, r=((R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem+2*S01_sila_materialu)-S01_tolerance_zavit/2)/2-S01_hloubka_zavitu/2-S01_sila_materialu, center = true, $fn=100); |
19 |
cylinder (h = S01_vyska_komponentu_na_lozisko+0.01, r=((R02_vzdalenost_mezi_uchyty_lopatek+2*L01_sila_zapusteni_drzaku+2*L01_hloubka_zapusteni+2*vule_mezi_statorem_rotorem)-S01_tolerance_zavit/2)/2-S01_hloubka_zavitu/2-S01_sila_materialu, center = true, $fn=100); |
| 21 |
|
20 |
|
| 22 |
//otvor na pruchod hridelky |
21 |
//otvor na pruchod hridelky |
| 23 |
translate([0,0,S01_sila_materialu/2]) |
22 |
translate([0,0,S01_sila_materialu/2]) |
| 24 |
cylinder (h = S01_sila_materialu+0.01, r=(lozisko_prumer_vnitrni+2*lozisko_prekryv+0.2)/2, center = true, $fn=100); |
23 |
cylinder (h = S01_sila_materialu+0.01, r=(lozisko_prumer_vnitrni+2*lozisko_prekryv+0.2)/2, center = true, $fn=100); |
| 25 |
} |
24 |
} |