WebSVN – MLAB – Rev 4151 and 3989 – Diff – /Modules/ARM/ODROID-U3/CAD/src/slic3r

Rev 3989		Rev 4151
Line 1...		Line 1...
1	`# generated by Slic3r 1.2.7-dev on Fri Mar 20 12:28:23 2015`	1	`# generated by Slic3r 1.2.9 on Fri Jul 31 16:30:17 2015`
2		-
3	`[filament:ABS_1.75]`	-
4	`bed_temperature = 90`	-
5	`bridge_fan_speed = 0`	-
6	`cooling = 1`	-
7	`disable_fan_first_layers = 0`	-
8	`extrusion_multiplier = 1.01`	-
9	`fan_always_on = 0`	-
10	`fan_below_layer_time = 1`	-
11	`filament_diameter = 1.75`	-
12	`first_layer_bed_temperature = 90`	-
13	`first_layer_temperature = 225`	-
14	`max_fan_speed = 0`	-
15	`min_fan_speed = 0`	-
16	`min_print_speed = 15`	-
17	`slowdown_below_layer_time = 20`	-
18	`temperature = 225`	-
19		-
20	`[filament:ABS_1.75 3D factories]`	-
21	`bed_temperature = 90`	-
22	`bridge_fan_speed = 0`	-
23	`cooling = 1`	-
24	`disable_fan_first_layers = 0`	-
25	`extrusion_multiplier = 1`	-
26	`fan_always_on = 0`	-
27	`fan_below_layer_time = 5`	-
28	`filament_diameter = 1.75`	-
29	`first_layer_bed_temperature = 90`	-
30	`first_layer_temperature = 225`	-
31	`max_fan_speed = 100`	-
32	`min_fan_speed = 50`	-
33	`min_print_speed = 15`	-
34	`slowdown_below_layer_time = 20`	-
35	`temperature = 225`	-
36		-
37	`[filament:ABS_1.75 red 3D factories]`	-
38	`bed_temperature = 90`	-
39	`bridge_fan_speed = 0`	-
40	`cooling = 1`	-
41	`disable_fan_first_layers = 0`	-
42	`extrusion_multiplier = 1`	-
43	`fan_always_on = 0`	-
44	`fan_below_layer_time = 5`	-
45	`filament_diameter = 1.73`	-
46	`first_layer_bed_temperature = 80`	-
47	`first_layer_temperature = 230`	-
48	`max_fan_speed = 60`	-
49	`min_fan_speed = 0`	-
50	`min_print_speed = 15`	-
51	`slowdown_below_layer_time = 20`	-
52	`temperature = 225`	-
53		-
54	`[filament:PLA_1.75]`	-
55	`bed_temperature = 0`	-
56	`bridge_fan_speed = 40`	-
57	`cooling = 1`	-
58	`disable_fan_first_layers = 0`	-
59	`extrusion_multiplier = 1`	-
60	`fan_always_on = 1`	-
61	`fan_below_layer_time = 1`	-
62	`filament_diameter = 1.75`	-
63	`first_layer_bed_temperature = 0`	-
64	`first_layer_temperature = 185`	-
65	`max_fan_speed = 50`	-
66	`min_fan_speed = 40`	-
67	`min_print_speed = 15`	-
68	`slowdown_below_layer_time = 20`	-
69	`temperature = 185`	-
70		-
71	`[filament:PLA_1.75 3D factories]`	-
72	`bed_temperature = 50`	-
73	`bridge_fan_speed = 50`	-
74	`cooling = 1`	-
75	`disable_fan_first_layers = 0`	-
76	`extrusion_multiplier = 0.9524`	-
77	`fan_always_on = 1`	-
78	`fan_below_layer_time = 60`	-
79	`filament_diameter = 1.75`	-
80	`first_layer_bed_temperature = 60`	-
81	`first_layer_temperature = 185`	-
82	`max_fan_speed = 100`	-
83	`min_fan_speed = 100`	-
84	`min_print_speed = 10`	-
85	`slowdown_below_layer_time = 30`	-
86	`temperature = 185`	-
87		-
88	`[filament:Simple Mode]`	-
89	`bed_temperature = 110`	-
90	`extrusion_multiplier = 1`	-
91	`filament_diameter = 1.75`	-
92	`first_layer_bed_temperature = 115`	-
93	`first_layer_temperature = 235`	-
94	`temperature = 230`	-
95		-
96	`[filament:slic3r_config]`	-
97	`bed_temperature = 90`	-
98	`bridge_fan_speed = 0`	-
99	`cooling = 1`	-
100	`disable_fan_first_layers = 0`	-
101	`extrusion_multiplier = 0.95`	-
102	`fan_always_on = 0`	-
103	`fan_below_layer_time = 5`	-
104	`filament_diameter = 1.75`	-
105	`first_layer_bed_temperature = 80`	-
106	`first_layer_temperature = 230`	-
107	`max_fan_speed = 100`	-
108	`min_fan_speed = 50`	-
109	`min_print_speed = 15`	-
110	`slowdown_below_layer_time = 20`	-
111	`temperature = 230`	-
112		-
113	`[presets]`	-
114	`filament = slic3r_config.ini`	-
115	`print = 0.2 layer.ini`	-
116	`printer = slic3r_config.ini`	-
117		-
118	`[print:0.2 layer]`	-
119	`avoid_crossing_perimeters = 0`	-
120	`bottom_solid_layers = 3`	-
121	`bridge_acceleration = 1000`	-
122	`bridge_flow_ratio = 1`	-
123	`bridge_speed = 15`	-
124	`brim_width = 10`	-
125	`complete_objects = 0`	-
126	`default_acceleration = 500`	-
127	`dont_support_bridges = 1`	-
128	`external_fill_pattern = rectilinear`	-
129	`external_perimeter_extrusion_width = 0`	-
130	`external_perimeter_speed = 90%`	-
131	`external_perimeters_first = 0`	-
132	`extra_perimeters = 1`	-
133	`extruder_clearance_height = 20`	-
134	`extruder_clearance_radius = 20`	-
135	`extrusion_width = 0`	-
136	`fill_angle = 45`	-
137	`fill_density = 15%`	-
138	`fill_pattern = honeycomb`	-
139	`first_layer_acceleration = 500`	-
140	`first_layer_extrusion_width = 200%`	-
141	`first_layer_height = 0.3`	-
142	`first_layer_speed = 60%`	-
143	`gap_fill_speed = 20`	-
144	`gcode_comments = 0`	-
145	`infill_acceleration = 500`	-
146	`infill_every_layers = 1`	-
147	`infill_extruder = 1`	-
148	`infill_extrusion_width = 0`	-
149	`infill_first = 0`	-
150	`infill_only_where_needed = 0`	-
151	`infill_overlap = 15%`	-
152	`infill_speed = 60`	-
153	`interface_shells = 0`	-
154	`layer_height = 0.2`	-
155	`min_skirt_length = 0`	-
156	`notes =`	-
157	`only_retract_when_crossing_perimeters = 1`	-
158	`ooze_prevention = 0`	-
159	`output_filename_format = [input_filename_base].gcode`	-
160	`overhangs = 1`	-
161	`perimeter_acceleration = 500`	-
162	`perimeter_extruder = 1`	-
163	`perimeter_extrusion_width = 0`	-
164	`perimeter_speed = 45`	-
165	`perimeters = 1`	-
166	`post_process =`	-
167	`raft_layers = 0`	-
168	`resolution = 0`	-
169	`seam_position = aligned`	-
170	`skirt_distance = 4`	-
171	`skirt_height = 1`	-
172	`skirts = 1`	-
173	`small_perimeter_speed = 30`	-
174	`solid_infill_below_area = 70`	-
175	`solid_infill_every_layers = 0`	-
176	`solid_infill_extruder = 1`	-
177	`solid_infill_extrusion_width = 0`	-
178	`solid_infill_speed = 55`	-
179	`spiral_vase = 0`	-
180	`standby_temperature_delta = -5`	-
181	`support_material = 0`	-
182	`support_material_angle = 0`	-
183	`support_material_contact_distance = 0.2`	-
184	`support_material_enforce_layers = 0`	-
185	`support_material_extruder = 1`	-
186	`support_material_extrusion_width = 0`	-
187	`support_material_interface_extruder = 1`	-
188	`support_material_interface_layers = 0`	-
189	`support_material_interface_spacing = 0`	-
190	`support_material_interface_speed = 100%`	-
191	`support_material_pattern = rectilinear`	-
192	`support_material_spacing = 2.5`	-
193	`support_material_speed = 60`	-
194	`support_material_threshold = 0`	-
195	`thin_walls = 1`	-
196	`threads = 2`	-
197	`top_infill_extrusion_width = 0`	-
198	`top_solid_infill_speed = 50`	-
199	`top_solid_layers = 3`	-
200	`travel_speed = 130`	-
201	`xy_size_compensation = 0`	-
202		-
203	`[print:0.3 layer]`	-
204	`avoid_crossing_perimeters = 0`	-
205	`bottom_solid_layers = 3`	-
206	`bridge_acceleration = 1000`	-
207	`bridge_flow_ratio = 1`	-
208	`bridge_speed = 10`	-
209	`brim_width = 0`	-
210	`complete_objects = 0`	-
211	`default_acceleration = 500`	-
212	`dont_support_bridges = 1`	-
213	`external_fill_pattern = rectilinear`	-
214	`external_perimeter_extrusion_width = 0`	-
215	`external_perimeter_speed = 90%`	-
216	`external_perimeters_first = 0`	-
217	`extra_perimeters = 1`	-
218	`extruder_clearance_height = 20`	-
219	`extruder_clearance_radius = 20`	-
220	`extrusion_width = 0`	-
221	`fill_angle = 45`	-
222	`fill_density = 25%`	-
223	`fill_pattern = line`	-
224	`first_layer_acceleration = 500`	-
225	`first_layer_extrusion_width = 180%`	-
226	`first_layer_height = 0.3`	-
227	`first_layer_speed = 60%`	-
228	`gap_fill_speed = 20`	-
229	`gcode_comments = 0`	-
230	`infill_acceleration = 500`	-
231	`infill_every_layers = 1`	-
232	`infill_extruder = 1`	-
233	`infill_extrusion_width = 0`	-
234	`infill_first = 0`	-
235	`infill_only_where_needed = 0`	-
236	`infill_overlap = 15%`	-
237	`infill_speed = 60`	-
238	`interface_shells = 0`	-
239	`layer_height = 0.3`	-
240	`min_skirt_length = 0`	-
241	`notes =`	-
242	`only_retract_when_crossing_perimeters = 1`	-
243	`ooze_prevention = 0`	-
244	`output_filename_format = [input_filename_base].gcode`	-
245	`overhangs = 1`	-
246	`perimeter_acceleration = 500`	-
247	`perimeter_extruder = 1`	-
248	`perimeter_extrusion_width = 0`	-
249	`perimeter_speed = 45`	-
250	`perimeters = 2`	-
251	`post_process =`	-
252	`raft_layers = 0`	-
253	`resolution = 0`	-
254	`seam_position = aligned`	-
255	`skirt_distance = 10`	-
256	`skirt_height = 1`	-
257	`skirts = 1`	-
258	`small_perimeter_speed = 30`	-
259	`solid_infill_below_area = 70`	-
260	`solid_infill_every_layers = 0`	-
261	`solid_infill_extruder = 1`	-
262	`solid_infill_extrusion_width = 0`	-
263	`solid_infill_speed = 55`	-
264	`spiral_vase = 0`	-
265	`standby_temperature_delta = -5`	-
266	`support_material = 0`	-
267	`support_material_angle = 0`	-
268	`support_material_contact_distance = 0.2`	-
269	`support_material_enforce_layers = 0`	-
270	`support_material_extruder = 1`	-
271	`support_material_extrusion_width = 0`	-
272	`support_material_interface_extruder = 1`	-
273	`support_material_interface_layers = 0`	-
274	`support_material_interface_spacing = 0`	-
275	`support_material_interface_speed = 100%`	-
276	`support_material_pattern = rectilinear`	-
277	`support_material_spacing = 2.5`	-
278	`support_material_speed = 60`	-
279	`support_material_threshold = 0`	-
280	`thin_walls = 1`	-
281	`threads = 4`	-
282	`top_infill_extrusion_width = 0`	-
283	`top_solid_infill_speed = 50`	-
284	`top_solid_layers = 3`	-
285	`travel_speed = 130`	-
286	`xy_size_compensation = 0`	-
287		-
288	`[print:0.3 layer brim]`	-
289	`avoid_crossing_perimeters = 0`	-
290	`bottom_solid_layers = 3`	-
291	`bridge_acceleration = 3000`	-
292	`bridge_flow_ratio = 1`	-
293	`bridge_speed = 10`	-
294	`brim_width = 10`	-
295	`complete_objects = 0`	-
296	`default_acceleration = 4000`	-
297	`dont_support_bridges = 1`	-
298	`external_fill_pattern = rectilinear`	-
299	`external_perimeter_extrusion_width = 0`	-
300	`external_perimeter_speed = 90%`	-
301	`external_perimeters_first = 0`	-
302	`extra_perimeters = 1`	-
303	`extruder_clearance_height = 20`	-
304	`extruder_clearance_radius = 20`	-
305	`extrusion_width = 0.6`	-
306	`fill_angle = 45`	-
307	`fill_density = 25%`	-
308	`fill_pattern = line`	-
309	`first_layer_acceleration = 0`	-
310	`first_layer_extrusion_width = 180%`	-
311	`first_layer_height = 0.3`	-
312	`first_layer_speed = 60%`	-
313	`gap_fill_speed = 20`	-
314	`gcode_comments = 0`	-
315	`infill_acceleration = 0`	-
316	`infill_every_layers = 1`	-
317	`infill_extruder = 1`	-
318	`infill_extrusion_width = 0`	-
319	`infill_first = 0`	-
320	`infill_only_where_needed = 0`	-
321	`infill_speed = 60`	-
322	`interface_shells = 0`	-
323	`layer_height = 0.3`	-
324	`min_skirt_length = 0`	-
325	`notes =`	-
326	`only_retract_when_crossing_perimeters = 1`	-
327	`ooze_prevention = 0`	-
328	`output_filename_format = [input_filename_base].gcode`	-
329	`overhangs = 1`	-
330	`perimeter_acceleration = 0`	-
331	`perimeter_extruder = 1`	-
332	`perimeter_extrusion_width = 0`	-
333	`perimeter_speed = 45`	-
334	`perimeters = 2`	-
335	`post_process =`	-
336	`raft_layers = 0`	-
337	`resolution = 0`	-
338	`seam_position = aligned`	-
339	`skirt_distance = 15`	-
340	`skirt_height = 1`	-
341	`skirts = 1`	-
342	`small_perimeter_speed = 30`	-
343	`solid_infill_below_area = 70`	-
344	`solid_infill_every_layers = 0`	-
345	`solid_infill_extruder = 1`	-
346	`solid_infill_extrusion_width = 0`	-
347	`solid_infill_speed = 55`	-
348	`spiral_vase = 0`	-
349	`standby_temperature_delta = -5`	-
350	`support_material = 0`	-
351	`support_material_angle = 0`	-
352	`support_material_enforce_layers = 0`	-
353	`support_material_extruder = 1`	-
354	`support_material_extrusion_width = 0`	-
355	`support_material_interface_extruder = 1`	-
356	`support_material_interface_layers = 0`	-
357	`support_material_interface_spacing = 0`	-
358	`support_material_interface_speed = 100%`	-
359	`support_material_pattern = rectilinear`	-
360	`support_material_spacing = 2.5`	-
361	`support_material_speed = 60`	-
362	`support_material_threshold = 0`	-
363	`thin_walls = 1`	-
364	`threads = 4`	-
365	`top_infill_extrusion_width = 0`	-
366	`top_solid_infill_speed = 50`	-
367	`top_solid_layers = 3`	-
368	`travel_speed = 130`	-
369	`xy_size_compensation = 0`	-
370		-
371	`[print:ABS 1.75]`	-
372	`avoid_crossing_perimeters = 0`	-
373	`bottom_solid_layers = 3`	-
374	`bridge_acceleration = 0`	-
375	`bridge_flow_ratio = 1.9`	-
376	`bridge_speed = 60`	-
377	`brim_width = 0`	-
378	`complete_objects = 0`	-
379	`default_acceleration = 0`	-
380	`dont_support_bridges = 1`	-
381	`external_fill_pattern = rectilinear`	-
382	`external_perimeter_speed = 70%`	-
383	`external_perimeters_first = 0`	-
384	`extra_perimeters = 1`	-
385	`extruder_clearance_height = 20`	-
386	`extruder_clearance_radius = 20`	-
387	`extrusion_width = 0`	-
388	`fill_angle = 45`	-
389	`fill_density = 40%`	-
390	`fill_pattern = honeycomb`	-
391	`first_layer_acceleration = 0`	-
392	`first_layer_extrusion_width = 200%`	-
393	`first_layer_height = 0.3`	-
394	`first_layer_speed = 30%`	-
395	`gap_fill_speed = 20`	-
396	`gcode_comments = 0`	-
397	`infill_acceleration = 0`	-
398	`infill_every_layers = 1`	-
399	`infill_extruder = 1`	-
400	`infill_extrusion_width = 0`	-
401	`infill_first = 0`	-
402	`infill_only_where_needed = 0`	-
403	`infill_speed = 60`	-
404	`interface_shells = 0`	-
405	`layer_height = 0.2`	-
406	`min_skirt_length = 0`	-
407	`notes =`	-
408	`only_retract_when_crossing_perimeters = 1`	-
409	`ooze_prevention = 0`	-
410	`output_filename_format = [input_filename_base].gcode`	-
411	`overhangs = 1`	-
412	`perimeter_acceleration = 0`	-
413	`perimeter_extruder = 1`	-
414	`perimeter_extrusion_width = 0`	-
415	`perimeter_speed = 30`	-
416	`perimeters = 3`	-
417	`post_process =`	-
418	`raft_layers = 0`	-
419	`resolution = 0`	-
420	`seam_position = aligned`	-
421	`skirt_distance = 6`	-
422	`skirt_height = 1`	-
423	`skirts = 1`	-
424	`small_perimeter_speed = 30`	-
425	`solid_infill_below_area = 70`	-
426	`solid_infill_every_layers = 0`	-
427	`solid_infill_extrusion_width = 0`	-
428	`solid_infill_speed = 60`	-
429	`spiral_vase = 0`	-
430	`standby_temperature_delta = -5`	-
431	`support_material = 0`	-
432	`support_material_angle = 0`	-
433	`support_material_enforce_layers = 0`	-
434	`support_material_extruder = 1`	-
435	`support_material_extrusion_width = 0`	-
436	`support_material_interface_extruder = 1`	-
437	`support_material_interface_layers = 3`	-
438	`support_material_interface_spacing = 0`	-
439	`support_material_interface_speed = 100%`	-
440	`support_material_pattern = pillars`	-
441	`support_material_spacing = 2.5`	-
442	`support_material_speed = 60`	-
443	`support_material_threshold = 0`	-
444	`thin_walls = 1`	-
445	`threads = 2`	-
446	`top_infill_extrusion_width = 0`	-
447	`top_solid_infill_speed = 50`	-
448	`top_solid_layers = 3`	-
449	`travel_speed = 130`	-
450		-
451	`[print:ABS_rocket]`	-
452	`avoid_crossing_perimeters = 0`	-
453	`bottom_solid_layers = 3`	-
454	`bridge_acceleration = 500`	-
455	`bridge_flow_ratio = 1.9`	-
456	`bridge_speed = 60`	-
457	`brim_width = 15`	-
458	`complete_objects = 0`	-
459	`default_acceleration = 1000`	-
460	`dont_support_bridges = 1`	-
461	`external_fill_pattern = rectilinear`	-
462	`external_perimeter_extrusion_width = 0`	-
463	`external_perimeter_speed = 70%`	-
464	`external_perimeters_first = 0`	-
465	`extra_perimeters = 1`	-
466	`extruder_clearance_height = 20`	-
467	`extruder_clearance_radius = 20`	-
468	`extrusion_width = 0.5`	-
469	`fill_angle = 45`	-
470	`fill_density = 40%`	-
471	`fill_pattern = honeycomb`	-
472	`first_layer_acceleration = 500`	-
473	`first_layer_extrusion_width = 200%`	-
474	`first_layer_height = 0.3`	-
475	`first_layer_speed = 30%`	-
476	`gap_fill_speed = 20`	-
477	`gcode_comments = 0`	-
478	`infill_acceleration = 500`	-
479	`infill_every_layers = 1`	-
480	`infill_extruder = 1`	-
481	`infill_extrusion_width = 0.4`	-
482	`infill_first = 0`	-
483	`infill_only_where_needed = 0`	-
484	`infill_speed = 60`	-
485	`interface_shells = 0`	-
486	`layer_height = 0.3`	-
487	`min_skirt_length = 0`	-
488	`notes =`	-
489	`only_retract_when_crossing_perimeters = 1`	-
490	`ooze_prevention = 0`	-
491	`output_filename_format = [input_filename_base].gcode`	-
492	`overhangs = 1`	-
493	`perimeter_acceleration = 500`	-
494	`perimeter_extruder = 1`	-
495	`perimeter_extrusion_width = 0`	-
496	`perimeter_speed = 30`	-
497	`perimeters = 3`	-
498	`post_process =`	-
499	`raft_layers = 0`	-
500	`resolution = 0`	-
501	`seam_position = aligned`	-
502	`skirt_distance = 6`	-
503	`skirt_height = 1`	-
504	`skirts = 1`	-
505	`small_perimeter_speed = 30`	-
506	`solid_infill_below_area = 70`	-
507	`solid_infill_every_layers = 0`	-
508	`solid_infill_extruder = 1`	-
509	`solid_infill_extrusion_width = 0`	-
510	`solid_infill_speed = 60`	-
511	`spiral_vase = 0`	-
512	`standby_temperature_delta = -5`	-
513	`support_material = 0`	-
514	`support_material_angle = 0`	-
515	`support_material_contact_distance = 0.2`	-
516	`support_material_enforce_layers = 0`	-
517	`support_material_extruder = 1`	-
518	`support_material_extrusion_width = 0`	-
519	`support_material_interface_extruder = 1`	-
520	`support_material_interface_layers = 3`	-
521	`support_material_interface_spacing = 0`	-
522	`support_material_interface_speed = 100%`	-
523	`support_material_pattern = pillars`	-
524	`support_material_spacing = 2.5`	-
525	`support_material_speed = 60`	-
526	`support_material_threshold = 0`	-
527	`thin_walls = 1`	-
528	`threads = 2`	-
529	`top_infill_extrusion_width = 0`	-
530	`top_solid_infill_speed = 50`	-
531	`top_solid_layers = 3`	-
532	`travel_speed = 130`	-
533	`xy_size_compensation = 0`	-
534		-
535	`[print:ABS_vase]`	-
536	`avoid_crossing_perimeters = 0`	2	`avoid_crossing_perimeters = 0`
537	`bottom_solid_layers = 3`	-
538	`bridge_acceleration = 500`	-
539	`bridge_flow_ratio = 1.9`	-
540	`bridge_speed = 60`	-
541	`brim_width = 5`	-
542	`complete_objects = 0`	-
543	`default_acceleration = 1000`	-
544	`dont_support_bridges = 1`	-
545	`external_fill_pattern = rectilinear`	-
546	`external_perimeter_extrusion_width = 0`	-
547	`external_perimeter_speed = 70%`	-
548	`external_perimeters_first = 0`	-
549	`extra_perimeters = 1`	-
550	`extruder_clearance_height = 20`	-
551	`extruder_clearance_radius = 20`	-
552	`extrusion_width = 0`	-
553	`fill_angle = 45`	-
554	`fill_density = 0%`	-
555	`fill_pattern = honeycomb`	-
556	`first_layer_acceleration = 500`	-
557	`first_layer_extrusion_width = 120%`	-
558	`first_layer_height = 0.3`	-
559	`first_layer_speed = 30%`	-
560	`gap_fill_speed = 20`	-
561	`gcode_comments = 0`	-
562	`infill_acceleration = 500`	-
563	`infill_every_layers = 1`	-
564	`infill_extruder = 1`	-
565	`infill_extrusion_width = 0`	-
566	`infill_first = 0`	-
567	`infill_only_where_needed = 0`	-
568	`infill_speed = 60`	-
569	`interface_shells = 0`	-
570	`layer_height = 0.3`	-
571	`min_skirt_length = 0`	-
572	`notes =`	-
573	`only_retract_when_crossing_perimeters = 1`	-
574	`ooze_prevention = 0`	-
575	`output_filename_format = [input_filename_base].gcode`	-
576	`overhangs = 1`	-
577	`perimeter_acceleration = 500`	-
578	`perimeter_extruder = 1`	-
579	`perimeter_extrusion_width = 0`	-
580	`perimeter_speed = 30`	-
581	`perimeters = 1`	-
582	`post_process =`	-
583	`raft_layers = 0`	-
584	`resolution = 0`	-
585	`seam_position = aligned`	-
586	`skirt_distance = 6`	-
587	`skirt_height = 1`	-
588	`skirts = 1`	-
589	`small_perimeter_speed = 30`	-
590	`solid_infill_below_area = 70`	-
591	`solid_infill_every_layers = 0`	-
592	`solid_infill_extruder = 1`	-
593	`solid_infill_extrusion_width = 0`	-
594	`solid_infill_speed = 60`	-
595	`spiral_vase = 1`	-
596	`standby_temperature_delta = -5`	-
597	`support_material = 0`	-
598	`support_material_angle = 0`	-
599	`support_material_contact_distance = 0.2`	-
600	`support_material_enforce_layers = 0`	-
601	`support_material_extruder = 1`	-
602	`support_material_extrusion_width = 0`	-
603	`support_material_interface_extruder = 1`	-
604	`support_material_interface_layers = 3`	-
605	`support_material_interface_spacing = 0`	-
606	`support_material_interface_speed = 100%`	-
607	`support_material_pattern = pillars`	-
608	`support_material_spacing = 2.5`	-
609	`support_material_speed = 60`	-
610	`support_material_threshold = 0`	-
611	`thin_walls = 1`	-
612	`threads = 2`	-
613	`top_infill_extrusion_width = 0`	-
614	`top_solid_infill_speed = 50`	-
615	`top_solid_layers = 0`	-
616	`travel_speed = 130`	-
617	`xy_size_compensation = 0`	-
618		-
619	`[print:Bridge]`	-
620	`avoid_crossing_perimeters = 0`	-
621	`bottom_solid_layers = 3`	-
622	`bridge_acceleration = 3000`	-
623	`bridge_flow_ratio = 1`	-
624	`bridge_speed = 10`	-
625	`brim_width = 5`	-
626	`complete_objects = 0`	-
627	`default_acceleration = 4000`	-
628	`dont_support_bridges = 1`	-
629	`external_fill_pattern = rectilinear`	-
630	`external_perimeter_speed = 90%`	-
631	`external_perimeters_first = 0`	-
632	`extra_perimeters = 1`	-
633	`extruder_clearance_height = 20`	-
634	`extruder_clearance_radius = 20`	-
635	`extrusion_width = 0.6`	-
636	`fill_angle = 45`	-
637	`fill_density = 25%`	-
638	`fill_pattern = line`	-
639	`first_layer_acceleration = 0`	-
640	`first_layer_extrusion_width = 125%`	-
641	`first_layer_height = 0.3`	-
642	`first_layer_speed = 60%`	-
643	`gap_fill_speed = 20`	-
644	`gcode_comments = 0`	-
645	`infill_acceleration = 0`	-
646	`infill_every_layers = 1`	-
647	`infill_extruder = 1`	-
648	`infill_extrusion_width = 0`	-
649	`infill_first = 0`	-
650	`infill_only_where_needed = 0`	-
651	`infill_speed = 60`	-
652	`interface_shells = 0`	-
653	`layer_height = 0.3`	-
654	`min_skirt_length = 0`	-
655	`notes =`	-
656	`only_retract_when_crossing_perimeters = 1`	-
657	`ooze_prevention = 0`	-
658	`output_filename_format = [input_filename_base].gcode`	-
659	`overhangs = 1`	-
660	`perimeter_acceleration = 0`	-
661	`perimeter_extruder = 1`	-
662	`perimeter_extrusion_width = 0`	-
663	`perimeter_speed = 45`	-
664	`perimeters = 2`	-
665	`post_process =`	-
666	`raft_layers = 0`	-
667	`resolution = 0`	-
668	`seam_position = random`	-
669	`skirt_distance = 10`	-
670	`skirt_height = 1`	-
671	`skirts = 1`	-
672	`small_perimeter_speed = 30`	-
673	`solid_infill_below_area = 70`	-
674	`solid_infill_every_layers = 0`	-
675	`solid_infill_extrusion_width = 0`	-
676	`solid_infill_speed = 55`	-
677	`spiral_vase = 0`	-
678	`standby_temperature_delta = -5`	-
679	`support_material = 0`	-
680	`support_material_angle = 0`	-
681	`support_material_enforce_layers = 0`	-
682	`support_material_extruder = 1`	-
683	`support_material_extrusion_width = 0`	-
684	`support_material_interface_extruder = 1`	-
685	`support_material_interface_layers = 0`	-
686	`support_material_interface_spacing = 0`	-
687	`support_material_interface_speed = 100%`	-
688	`support_material_pattern = rectilinear`	-
689	`support_material_spacing = 2.5`	-
690	`support_material_speed = 60`	-
691	`support_material_threshold = 0`	-
692	`thin_walls = 1`	-
693	`threads = 4`	-
694	`top_infill_extrusion_width = 0`	-
695	`top_solid_infill_speed = 50`	-
696	`top_solid_layers = 3`	-
697	`travel_speed = 100`	-
698		-
699	`[print:Simple Mode]`	-
700	`bottom_solid_layers = 3`	-
701	`brim_width = 0`	-
702	`complete_objects = 0`	-
703	`extruder_clearance_height = 20`	-
704	`extruder_clearance_radius = 20`	-
705	`fill_density = 40%`	-
706	`fill_pattern = honeycomb`	-
707	`infill_speed = 60`	-
708	`layer_height = 0.2`	-
709	`perimeter_speed = 30`	-
710	`perimeters = 3`	-
711	`raft_layers = 0`	-
712	`support_material = 0`	-
713	`support_material_spacing = 2.5`	-
714	`top_solid_layers = 3`	-
715	`travel_speed = 130`	-
716		-
717	`[print:Standard]`	-
718	`avoid_crossing_perimeters = 0`	-
719	`bottom_solid_layers = 3`	-
720	`bridge_acceleration = 0`	-
721	`bridge_flow_ratio = 1`	-
722	`bridge_speed = 20`	-
723	`brim_width = 0`	-
724	`complete_objects = 0`	-
725	`default_acceleration = 0`	-
726	`dont_support_bridges = 1`	-
727	`external_fill_pattern = rectilinear`	-
728	`external_perimeter_speed = 90%`	-
729	`external_perimeters_first = 0`	-
730	`extra_perimeters = 0`	-
731	`extruder_clearance_height = 20`	-
732	`extruder_clearance_radius = 20`	-
733	`extrusion_width = 0.6`	-
734	`fill_angle = 45`	-
735	`fill_density = 25%`	-
736	`fill_pattern = line`	-
737	`first_layer_acceleration = 0`	-
738	`first_layer_extrusion_width = 200%`	-
739	`first_layer_height = 0.3`	-
740	`first_layer_speed = 60%`	-
741	`gap_fill_speed = 20`	-
742	`gcode_comments = 0`	-
743	`infill_acceleration = 0`	-
744	`infill_every_layers = 1`	-
745	`infill_extruder = 1`	-
746	`infill_extrusion_width = 0`	-
747	`infill_first = 0`	-
748	`infill_only_where_needed = 0`	-
749	`infill_speed = 60`	-
750	`interface_shells = 0`	-
751	`layer_height = 0.3`	-
752	`min_skirt_length = 0`	-
753	`notes =`	-
754	`only_retract_when_crossing_perimeters = 1`	-
755	`ooze_prevention = 0`	-
756	`output_filename_format = [input_filename_base].gcode`	-
757	`overhangs = 1`	-
758	`perimeter_acceleration = 0`	-
759	`perimeter_extruder = 1`	-
760	`perimeter_extrusion_width = 0`	-
761	`perimeter_speed = 45`	-
762	`perimeters = 2`	-
763	`post_process =`	-
764	`raft_layers = 0`	-
765	`resolution = 0`	-
766	`seam_position = aligned`	-
767	`skirt_distance = 4`	-
768	`skirt_height = 1`	-
769	`skirts = 1`	-
770	`small_perimeter_speed = 30`	-
771	`solid_infill_below_area = 70`	-
772	`solid_infill_every_layers = 0`	-
773	`solid_infill_extrusion_width = 0`	-
774	`solid_infill_speed = 55`	-
775	`spiral_vase = 0`	-
776	`standby_temperature_delta = -5`	-
777	`support_material = 0`	-
778	`support_material_angle = 0`	-
779	`support_material_enforce_layers = 0`	-
780	`support_material_extruder = 1`	-
781	`support_material_extrusion_width = 0`	-
782	`support_material_interface_extruder = 1`	-
783	`support_material_interface_layers = 0`	-
784	`support_material_interface_spacing = 0`	-
785	`support_material_interface_speed = 100%`	-
786	`support_material_pattern = rectilinear`	-
787	`support_material_spacing = 2.5`	-
788	`support_material_speed = 60`	-
789	`support_material_threshold = 0`	-
790	`thin_walls = 1`	-
791	`threads = 2`	-
792	`top_infill_extrusion_width = 0`	-
793	`top_solid_infill_speed = 50`	-
794	`top_solid_layers = 3`	-
795	`travel_speed = 130`	-
796		-
797	`[print:Weather_screen]`	-
798	`avoid_crossing_perimeters = 0`	-
799	`bottom_solid_layers = 3`	-
800	`bridge_acceleration = 3000`	-
801	`bridge_flow_ratio = 1`	-
802	`bridge_speed = 10`	-
803	`brim_width = 5`	-
804	`complete_objects = 0`	-
805	`default_acceleration = 4000`	-
806	`dont_support_bridges = 1`	-
807	`external_fill_pattern = concentric`	-
808	`external_perimeter_speed = 90%`	-
809	`external_perimeters_first = 0`	-
810	`extra_perimeters = 1`	-
811	`extruder_clearance_height = 20`	-
812	`extruder_clearance_radius = 20`	-
813	`extrusion_width = 0.6`	-
814	`fill_angle = 45`	-
815	`fill_density = 90%`	-
816	`fill_pattern = concentric`	-
817	`first_layer_acceleration = 0`	-
818	`first_layer_extrusion_width = 200%`	-
819	`first_layer_height = 0.3`	-
820	`first_layer_speed = 60%`	-
821	`gap_fill_speed = 20`	-
822	`gcode_comments = 0`	-
823	`infill_acceleration = 0`	-
824	`infill_every_layers = 1`	-
825	`infill_extruder = 1`	-
826	`infill_extrusion_width = 0`	-
827	`infill_first = 0`	-
828	`infill_only_where_needed = 0`	-
829	`infill_speed = 60`	-
830	`interface_shells = 0`	-
831	`layer_height = 0.3`	-
832	`min_skirt_length = 0`	-
833	`notes =`	-
834	`only_retract_when_crossing_perimeters = 1`	-
835	`ooze_prevention = 0`	-
836	`output_filename_format = [input_filename_base].gcode`	-
837	`overhangs = 1`	-
838	`perimeter_acceleration = 0`	-
839	`perimeter_extruder = 1`	-
840	`perimeter_extrusion_width = 0`	-
841	`perimeter_speed = 45`	-
842	`perimeters = 3`	-
843	`post_process =`	-
844	`raft_layers = 0`	-
845	`resolution = 0`	-
846	`seam_position = aligned`	-
847	`skirt_distance = 5`	-
848	`skirt_height = 1`	-
849	`skirts = 0`	-
850	`small_perimeter_speed = 30`	-
851	`solid_infill_below_area = 70`	-
852	`solid_infill_every_layers = 0`	-
853	`solid_infill_extrusion_width = 0`	-
854	`solid_infill_speed = 55`	-
855	`spiral_vase = 0`	-
856	`standby_temperature_delta = -5`	-
857	`support_material = 0`	-
858	`support_material_angle = 0`	-
859	`support_material_enforce_layers = 0`	-
860	`support_material_extruder = 1`	-
861	`support_material_extrusion_width = 0`	-
862	`support_material_interface_extruder = 1`	-
863	`support_material_interface_layers = 0`	-
864	`support_material_interface_spacing = 0`	-
865	`support_material_interface_speed = 100%`	-
866	`support_material_pattern = rectilinear`	-
867	`support_material_spacing = 2.5`	-
868	`support_material_speed = 60`	-
869	`support_material_threshold = 0`	-
870	`thin_walls = 1`	-
871	`threads = 2`	-
872	`top_infill_extrusion_width = 0`	-
873	`top_solid_infill_speed = 50`	-
874	`top_solid_layers = 3`	-
875	`travel_speed = 130`	-
876		-
877	`[print:slic3r_config]`	-
878	`avoid_crossing_perimeters = 0`	-
879	`bottom_solid_layers = 3`	-
880	`bridge_acceleration = 1000`	-
881	`bridge_flow_ratio = 1`	-
882	`bridge_speed = 10`	-
883	`brim_width = 10`	-
884	`complete_objects = 0`	-
885	`default_acceleration = 500`	-
886	`dont_support_bridges = 1`	-
887	`external_fill_pattern = rectilinear`	-
888	`external_perimeter_extrusion_width = 0`	-
889	`external_perimeter_speed = 90%`	-
890	`external_perimeters_first = 0`	-
891	`extra_perimeters = 1`	-
892	`extruder_clearance_height = 20`	-
893	`extruder_clearance_radius = 20`	-
894	`extrusion_width = 0`	-
895	`fill_angle = 45`	-
896	`fill_density = 15%`	-
897	`fill_pattern = honeycomb`	-
898	`first_layer_acceleration = 500`	-
899	`first_layer_extrusion_width = 200%`	-
900	`first_layer_height = 0.3`	-
901	`first_layer_speed = 60%`	-
902	`gap_fill_speed = 20`	-
903	`gcode_comments = 0`	-
904	`infill_acceleration = 500`	-
905	`infill_every_layers = 1`	-
906	`infill_extruder = 1`	-
907	`infill_extrusion_width = 0`	-
908	`infill_first = 0`	-
909	`infill_only_where_needed = 0`	-
910	`infill_overlap = 15%`	-
911	`infill_speed = 60`	-
912	`interface_shells = 0`	-
913	`layer_height = 0.3`	-
914	`min_skirt_length = 0`	-
915	`notes =`	-
916	`only_retract_when_crossing_perimeters = 1`	-
917	`ooze_prevention = 0`	-
918	`output_filename_format = [input_filename_base].gcode`	-
919	`overhangs = 1`	-
920	`perimeter_acceleration = 500`	-
921	`perimeter_extruder = 1`	-
922	`perimeter_extrusion_width = 0`	-
923	`perimeter_speed = 45`	-
924	`perimeters = 2`	-
925	`post_process =`	-
926	`raft_layers = 0`	-
927	`resolution = 0`	-
928	`seam_position = aligned`	-
929	`skirt_distance = 10`	-
930	`skirt_height = 1`	-
931	`skirts = 1`	-
932	`small_perimeter_speed = 30`	-
933	`solid_infill_below_area = 70`	-
934	`solid_infill_every_layers = 0`	-
935	`solid_infill_extruder = 1`	-
936	`solid_infill_extrusion_width = 0`	-
937	`solid_infill_speed = 55`	-
938	`spiral_vase = 0`	-
939	`standby_temperature_delta = -5`	-
940	`support_material = 0`	-
941	`support_material_angle = 0`	-
942	`support_material_contact_distance = 0.2`	-
943	`support_material_enforce_layers = 0`	-
944	`support_material_extruder = 1`	-
945	`support_material_extrusion_width = 0`	-
946	`support_material_interface_extruder = 1`	-
947	`support_material_interface_layers = 0`	-
948	`support_material_interface_spacing = 0`	-
949	`support_material_interface_speed = 100%`	-
950	`support_material_pattern = rectilinear`	-
951	`support_material_spacing = 2.5`	-
952	`support_material_speed = 60`	-
953	`support_material_threshold = 0`	-
954	`thin_walls = 1`	-
955	`threads = 4`	-
956	`top_infill_extrusion_width = 0`	-
957	`top_solid_infill_speed = 50`	-
958	`top_solid_layers = 3`	-
959	`travel_speed = 130`	-
960	`xy_size_compensation = 0`	-
961		-
962	`[printer:RebeliX]`	-
963	`bed_shape = 0x0,180x0,180x180,0x180`	3	`bed_shape = 0x0,200x0,200x200,0x200`
964	`before_layer_gcode =`	4	`bed_temperature = 0`
965	`end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84 ; disable motors\n`	-
966	`extruder_offset = 0x0`	-
967	`gcode_flavor = reprap`	-
968	`layer_gcode =`	-
969	`nozzle_diameter = 0.4`	-
970	`octoprint_apikey = B14197D3716442D4B0BB8F485877E31E`	-
971	`octoprint_host = 192.168.1.106:5000`	-
972	`pressure_advance = 0`	-
973	`retract_before_travel = 2`	-
974	`retract_layer_change = 1`	-
975	`retract_length = 1.3`	-
976	`retract_length_toolchange = 3`	-
977	`retract_lift = 0`	-
978	`retract_restart_extra = 0`	-
979	`retract_restart_extra_toolchange = 0`	-
980	`retract_speed = 60`	-
981	`start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder`	-
982	`toolchange_gcode =`	-
983	`use_firmware_retraction = 0`	-
984	`use_relative_e_distances = 1`	-
985	`use_volumetric_e = 0`	-
986	`vibration_limit = 0`	-
987	`wipe = 1`	-
988	`z_offset = 0`	-
989		-
990	`[printer:Simple Mode]`	-
991	`bed_shape = 0x0,180x0,180x180,0x180`	-
992	`end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n`	-
993	`gcode_flavor = reprap`	-
994	`nozzle_diameter = 0.3`	-
995	`retract_length = 1`	-
996	`retract_lift = 0`	-
997	`start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n`	-
998	`z_offset = 0`	-
999		-
1000	`[printer:slic3r_config]`	-
1001	`bed_shape = 0x0,180x0,180x180,0x180`	-
1002	`before_layer_gcode =`	5	`before_layer_gcode =`
1003	`end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0 ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84 ; disable motors\n`	-
1004	`extruder_offset = 0x0`	-
1005	`gcode_flavor = reprap`	-
1006	`layer_gcode =`	-
1007	`nozzle_diameter = 0.4`	-
1008	`octoprint_apikey = B14197D3716442D4B0BB8F485877E31E`	-
1009	`octoprint_host = 192.168.1.106:5000`	-
1010	`pressure_advance = 0`	-
1011	`retract_before_travel = 2`	-
1012	`retract_layer_change = 1`	-
1013	`retract_length = 1.3`	-
1014	`retract_length_toolchange = 3`	-
1015	`retract_lift = 0`	-
1016	`retract_restart_extra = 0`	-
1017	`retract_restart_extra_toolchange = 0`	-
1018	`retract_speed = 60`	-
1019	`start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder`	-
1020	`toolchange_gcode =`	-
1021	`use_firmware_retraction = 0`	-
1022	`use_relative_e_distances = 1`	-
1023	`use_volumetric_e = 0`	-
1024	`vibration_limit = 0`	-
1025	`wipe = 1`	-
1026	`z_offset = 0`	-
1027		-
1028	`[settings]`	-
1029	`autocenter = 1`	-
1030	`mode = expert`	-
1031		-
1032	`[simple]`	-
1033	`avoid_crossing_perimeters = 1`	-
1034	`bed_shape = 0x0,180x0,180x180,0x180`	-
1035	`bed_temperature = 110`	-
1036	`bottom_solid_layers = 3`	6	`bottom_solid_layers = 3`
1037	`bridge_acceleration = 0`	7	`bridge_acceleration = 0`
1038	`bridge_fan_speed = 100`	8	`bridge_fan_speed = 100`
1039	`bridge_flow_ratio = 1`	9	`bridge_flow_ratio = 1`
1040	`bridge_speed = 60`	10	`bridge_speed = 60`
1041	`brim_width = 0`	11	`brim_width = 0`
1042	`complete_objects = 0`	12	`complete_objects = 0`
1043	`cooling = 1`	13	`cooling = 1`
1044	`default_acceleration = 0`	14	`default_acceleration = 0`
1045	`disable_fan_first_layers = 1`	15	`disable_fan_first_layers = 3`
1046	`dont_support_bridges = 1`	16	`dont_support_bridges = 1`
1047	`duplicate_distance = 6`	17	`duplicate_distance = 6`
1048	`end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n`	18	`end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n`
1049	`external_fill_pattern = rectilinear`	19	`external_fill_pattern = rectilinear`
-		20	`external_perimeter_extrusion_width = 0`
1050	`external_perimeter_speed = 70%`	21	`external_perimeter_speed = 50%`
1051	`external_perimeters_first = 0`	22	`external_perimeters_first = 0`
1052	`extra_perimeters = 1`	23	`extra_perimeters = 1`
1053	`extruder_clearance_height = 20`	24	`extruder_clearance_height = 20`
1054	`extruder_clearance_radius = 20`	25	`extruder_clearance_radius = 20`
1055	`extruder_offset = 0x0`	26	`extruder_offset = 0x0`
1056	`extrusion_axis = E`	27	`extrusion_axis = E`
1057	`extrusion_multiplier = 1`	28	`extrusion_multiplier = 1`
1058	`extrusion_width = 0`	29	`extrusion_width = 0`
1059	`fan_always_on = 0`	30	`fan_always_on = 0`
1060	`fan_below_layer_time = 60`	31	`fan_below_layer_time = 60`
-		32	`filament_colour = #FFFFFF`
1061	`filament_diameter = 1.75`	33	`filament_diameter = 3`
1062	`fill_angle = 45`	34	`fill_angle = 45`
1063	`fill_density = 40%`	35	`fill_density = 20%`
1064	`fill_pattern = honeycomb`	36	`fill_pattern = honeycomb`
1065	`first_layer_acceleration = 0`	37	`first_layer_acceleration = 0`
1066	`first_layer_bed_temperature = 115`	38	`first_layer_bed_temperature = 0`
1067	`first_layer_extrusion_width = 200%`	39	`first_layer_extrusion_width = 200%`
1068	`first_layer_height = 0.3`	40	`first_layer_height = 0.35`
1069	`first_layer_speed = 30%`	41	`first_layer_speed = 30`
1070	`first_layer_temperature = 235`	42	`first_layer_temperature = 210`
1071	`gap_fill_speed = 20`	43	`gap_fill_speed = 20`
1072	`gcode_arcs = 0`	44	`gcode_arcs = 0`
1073	`gcode_comments = 0`	45	`gcode_comments = 0`
1074	`gcode_flavor = reprap`	46	`gcode_flavor = reprap`
1075	`infill_acceleration = 0`	47	`infill_acceleration = 0`
1076	`infill_every_layers = 10`	48	`infill_every_layers = 1`
1077	`infill_extruder = 1`	49	`infill_extruder = 1`
1078	`infill_extrusion_width = 0`	50	`infill_extrusion_width = 0`
1079	`infill_first = 0`	51	`infill_first = 0`
1080	`infill_only_where_needed = 0`	52	`infill_only_where_needed = 0`
-		53	`infill_overlap = 15%`
1081	`infill_speed = 60`	54	`infill_speed = 80`
1082	`interface_shells = 0`	55	`interface_shells = 0`
1083	`layer_gcode =`	56	`layer_gcode =`
1084	`layer_height = 0.2`	57	`layer_height = 0.3`
1085	`max_fan_speed = 100`	58	`max_fan_speed = 100`
-		59	`max_print_speed = 80`
-		60	`max_volumetric_speed = 0`
1086	`min_fan_speed = 35`	61	`min_fan_speed = 35`
1087	`min_print_speed = 10`	62	`min_print_speed = 10`
1088	`min_skirt_length = 0`	63	`min_skirt_length = 0`
1089	`notes =`	64	`notes =`
1090	`nozzle_diameter = 0.3`	65	`nozzle_diameter = 0.5`
-		66	`octoprint_apikey =`
-		67	`octoprint_host =`
1091	`only_retract_when_crossing_perimeters = 1`	68	`only_retract_when_crossing_perimeters = 1`
1092	`ooze_prevention = 0`	69	`ooze_prevention = 0`
1093	`output_filename_format = [input_filename_base].gcode`	70	`output_filename_format = [input_filename_base].gcode`
1094	`overhangs = 1`	71	`overhangs = 1`
1095	`perimeter_acceleration = 0`	72	`perimeter_acceleration = 0`
1096	`perimeter_extruder = 1`	73	`perimeter_extruder = 1`
1097	`perimeter_extrusion_width = 0`	74	`perimeter_extrusion_width = 0`
1098	`perimeter_speed = 30`	75	`perimeter_speed = 60`
1099	`perimeters = 3`	76	`perimeters = 3`
1100	`post_process =`	77	`post_process =`
-		78	`pressure_advance = 0`
1101	`raft_layers = 0`	79	`raft_layers = 0`
1102	`resolution = 0`	80	`resolution = 0`
1103	`retract_before_travel = 2`	81	`retract_before_travel = 2`
1104	`retract_layer_change = 1`	82	`retract_layer_change = 0`
1105	`retract_length = 1`	83	`retract_length = 2`
1106	`retract_length_toolchange = 10`	84	`retract_length_toolchange = 10`
1107	`retract_lift = 0`	85	`retract_lift = 0`
1108	`retract_restart_extra = 0`	86	`retract_restart_extra = 0`
1109	`retract_restart_extra_toolchange = 0`	87	`retract_restart_extra_toolchange = 0`
1110	`retract_speed = 30`	88	`retract_speed = 40`
1111	`seam_position = aligned`	89	`seam_position = aligned`
1112	`skirt_distance = 6`	90	`skirt_distance = 6`
1113	`skirt_height = 1`	91	`skirt_height = 1`
1114	`skirts = 1`	92	`skirts = 1`
1115	`slowdown_below_layer_time = 30`	93	`slowdown_below_layer_time = 5`
1116	`small_perimeter_speed = 30`	94	`small_perimeter_speed = 15`
1117	`solid_infill_below_area = 70`	95	`solid_infill_below_area = 70`
1118	`solid_infill_every_layers = 0`	96	`solid_infill_every_layers = 0`
-		97	`solid_infill_extruder = 1`
1119	`solid_infill_extrusion_width = 0`	98	`solid_infill_extrusion_width = 0`
1120	`solid_infill_speed = 60`	99	`solid_infill_speed = 20`
1121	`spiral_vase = 0`	100	`spiral_vase = 0`
1122	`standby_temperature_delta = -5`	101	`standby_temperature_delta = -5`
1123	`start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n`	102	`start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n`
1124	`support_material = 0`	103	`support_material = 0`
1125	`support_material_angle = 0`	104	`support_material_angle = 0`
-		105	`support_material_contact_distance = 0.2`
1126	`support_material_enforce_layers = 0`	106	`support_material_enforce_layers = 0`
1127	`support_material_extruder = 1`	107	`support_material_extruder = 1`
1128	`support_material_extrusion_width = 0`	108	`support_material_extrusion_width = 0`
1129	`support_material_interface_extruder = 1`	109	`support_material_interface_extruder = 1`
1130	`support_material_interface_layers = 3`	110	`support_material_interface_layers = 3`
Line 1132...		Line 112...
1132	`support_material_interface_speed = 100%`	112	`support_material_interface_speed = 100%`
1133	`support_material_pattern = pillars`	113	`support_material_pattern = pillars`
1134	`support_material_spacing = 2.5`	114	`support_material_spacing = 2.5`
1135	`support_material_speed = 60`	115	`support_material_speed = 60`
1136	`support_material_threshold = 0`	116	`support_material_threshold = 0`
1137	`temperature = 230`	117	`temperature = 210`
1138	`thin_walls = 1`	118	`thin_walls = 1`
1139	`threads = 2`	119	`threads = 2`
1140	`toolchange_gcode =`	120	`toolchange_gcode =`
1141	`top_infill_extrusion_width = 0`	121	`top_infill_extrusion_width = 0`
1142	`top_solid_infill_speed = 50`	122	`top_solid_infill_speed = 15`
1143	`top_solid_layers = 3`	123	`top_solid_layers = 3`
1144	`travel_speed = 130`	124	`travel_speed = 130`
1145	`use_firmware_retraction = 0`	125	`use_firmware_retraction = 0`
1146	`use_relative_e_distances = 0`	126	`use_relative_e_distances = 0`
-		127	`use_volumetric_e = 0`
1147	`vibration_limit = 0`	128	`vibration_limit = 0`
1148	`wipe = 0`	129	`wipe = 0`
-		130	`xy_size_compensation = 0`
1149	`z_offset = 0`	131	`z_offset = 0`

Subversion Repositories – MLAB

(root)/Modules/ARM/ODROID-U3/CAD/src/slic3r_config.ini

Rev 3989 → Rev 4151