#!/usr/bin/python
# -------------------------------------------
# HBSTEP01B Stepper Motor control test code
# -------------------------------------------
#
# Program uses MLAB Python modules library from https://github.com/MLAB-project/pymlab


#uncomment for debbug purposes
#import logging
#logging.basicConfig(level=logging.DEBUG) 

import sys
import time
from pymlab import config
import pylirc       # infrared receiver binding

#### Script Arguments ###############################################

if len(sys.argv) == 2:
    SPEED = eval(sys.argv[1])

else:
    sys.stderr.write("Invalid number of arguments.\n")
    sys.stderr.write("Usage: %s BASE_SPEED (in steps/s)\n" % (sys.argv[0], ))
    sys.exit(1)

# Begin of Class Axis --------------------------------------------------

class axis:
    def __init__(self, SPI_CS, Direction, StepsPerUnit, MaxSpeed):
        ' One axis of robot '
        self.CS = SPI_CS
        self.Dir = Direction
        self.SPU = StepsPerUnit
        self.maxspeed = MaxSpeed

        self.L6470_ABS_POS      =0x01
        self.L6470_EL_POS       =0x02
        self.L6470_MARK         =0x03
        self.L6470_SPEED        =0x04
        self.L6470_ACC          =0x05
        self.L6470_DEC          =0x06
        self.L6470_MAX_SPEED    =0x07
        self.L6470_MIN_SPEED    =0x08
        self.L6470_FS_SPD       =0x15
        self.L6470_KVAL_HOLD    =0x09
        self.L6470_KVAL_RUN     =0x0A
        self.L6470_KVAL_ACC     =0x0B
        self.L6470_KVAL_DEC     =0x0C
        self.L6470_INT_SPEED    =0x0D
        self.L6470_ST_SLP       =0x0E
        self.L6470_FN_SLP_ACC   =0x0F
        self.L6470_FN_SLP_DEC   =0x10
        self.L6470_K_THERM      =0x11
        self.L6470_ADC_OUT      =0x12
        self.L6470_OCD_TH       =0x13
        self.L6470_STALL_TH     =0x14
        self.L6470_STEP_MODE    =0x16
        self.L6470_ALARM_EN     =0x17
        self.L6470_CONFIG       =0x18
        self.L6470_STATUS       =0x19

        self.Reset()
        self.Initialize()
        self.MaxSpeed(self.maxspeed)

    def Reset(self):
        'Reset the Axis'
        spi.SPI_write_byte(self.CS, 0xC0)      # reset

    def Initialize(self):
        'set default parameters for H-bridge '
#        spi.SPI_write_byte(self.CS, 0x14)      # Stall Treshold setup
#        spi.SPI_write_byte(self.CS, 0xFF)  
#        spi.SPI_write_byte(self.CS, 0x13)      # Over Current Treshold setup 
#        spi.SPI_write_byte(self.CS, 0xFF)  
        spi.SPI_write_byte(self.CS, 0x15)      # Full Step speed 
        spi.SPI_write_byte(self.CS, 0xFF)
        spi.SPI_write_byte(self.CS, 0xFF) 
        spi.SPI_write_byte(self.CS, 0x05)      # ACC 
        spi.SPI_write_byte(self.CS, 0x00)
        spi.SPI_write_byte(self.CS, 0x10) 
        spi.SPI_write_byte(self.CS, 0x06)      # DEC 
        spi.SPI_write_byte(self.CS, 0x00)
        spi.SPI_write_byte(self.CS, 0x10) 
        spi.SPI_write_byte(self.CS, self.L6470_KVAL_RUN)      # KVAL_RUN
        spi.SPI_write_byte(self.CS, 0x58)
        spi.SPI_write_byte(self.CS, self.L6470_KVAL_ACC)      # KVAL_ACC
        spi.SPI_write_byte(self.CS, 0x58)
        spi.SPI_write_byte(self.CS, self.L6470_KVAL_DEC)      # KVAL_DEC
        spi.SPI_write_byte(self.CS, 0x58)
        spi.SPI_write_byte(self.CS, 0x18)      # CONFIG
        spi.SPI_write_byte(self.CS, 0b00101110)                 # spolecny byte pro obe konfigurace
        spi.SPI_write_byte(self.CS, 0b10000000)                 # konfigurace pro interni oscilator
#        spi.SPI_write_byte(self.CS, 0b10000110)                # konfigurace s externim oscilatorem
        self.MaxSpeed(self.maxspeed)

    def setKVAL(self, hold = 0.5, run = 0.5, acc = 0.5, dec = 0.5):
        """ The available range is from 0 to 0.996 x VS with a resolution of 0.004 x VS """

    def setOverCurrentTH(self, hold = 0.5, run = 0.5, acc = 0.5, dec = 0.5):
        """ The available range is from 375 mA to 6 A, in steps of 375 mA """

    def MaxSpeed(self, speed):
        'Setup of maximum speed in steps/s. The available range is from 15.25 to 15610 step/s with a resolution of 15.25 step/s.'
        speed_value = int(speed / 15.25)
        if (speed_value <= 0):
            speed_value = 1
        elif (speed_value >= 1023):
            speed_value = 1023

        data = [(speed_value >> i & 0xff) for i in (8,0)]
        spi.SPI_write_byte(self.CS, self.L6470_MAX_SPEED)       # Max Speed setup 
        spi.SPI_write_byte(self.CS, data[0])
        spi.SPI_write_byte(self.CS, data[1])
        return (speed_value * 15.25)

    def ReleaseSW(self):
        ' Go away from Limit Switch '
        while self.ReadStatusBit(2) == 1:           # is Limit Switch ON ?
            spi.SPI_write_byte(self.CS, 0x92 | (~self.Dir & 1))     # release SW 
            while self.IsBusy():
                pass
            self.MoveWait(10)           # move 10 units away
 
    def GoZero(self, speed):
        ' Go to Zero position '
        self.ReleaseSW()

        spi.SPI_write_byte(self.CS, 0x82 | (self.Dir & 1))       # Go to Zero
        spi.SPI_write_byte(self.CS, 0x00)
        spi.SPI_write_byte(self.CS, speed)  
        while self.IsBusy():
            pass
        time.sleep(0.3)
        self.ReleaseSW()

    def GetStatus(self):
        #self.spi.xfer([0b11010000])  # Get status command from datasheet - does not work for uknown rasons
        spi.SPI_write_byte(self.CS, 0x39)       # Gotparam  command on status register
        spi.SPI_write_byte(self.CS, 0x00)
        data = [spi.SPI_read_byte()]
        spi.SPI_write_byte(self.CS, 0x00)
        data = data + [spi.SPI_read_byte()]

        status = dict([('SCK_MOD',data[0] & 0x80 == 0x80),  #The SCK_MOD bit is an active high flag indicating that the device is working in Step-clock mode. In this case the step-clock signal should be provided through the STCK input pin. The DIR bit indicates the current motor direction
                    ('STEP_LOSS_B',data[0] & 0x40 == 0x40),
                    ('STEP_LOSS_A',data[0] & 0x20 == 0x20),
                    ('OCD',data[0] & 0x10 == 0x10),
                    ('TH_SD',data[0] & 0x08 == 0x08),
                    ('TH_WRN',data[0] & 0x04 == 0x04),
                    ('UVLO',data[0] & 0x02 == 0x02),
                    ('WRONG_CMD',data[0] & 0x01 == 0x01),   #The NOTPERF_CMD and WRONG_CMD flags are active high and indicate, respectively, that the command received by SPI cannot be performed or does not exist at all.
                    ('NOTPERF_CMD',data[1] & 0x80 == 0x80),
                    ('MOT_STATUS',data[1] & 0x60),
                    ('DIR',data[1] & 0x10 == 0x10),
                    ('SW_EVN',data[1] & 0x08 == 0x08),
                    ('SW_F',data[1] & 0x04 == 0x04),        #The SW_F flag reports the SW input status (low for open and high for closed).
                    ('BUSY',data[1] & 0x02 != 0x02),
                    ('HIZ',data[1] & 0x01 == 0x01)])
        return status

    def GetACC(self):
#        self.spi.xfer([0x29])       # Gotparam  command on status register
        spi.SPI_write_byte(self.CS, self.L6470_ACC + 0x20)  # TODO check register read address seting         
        spi.SPI_write_byte(self.CS, 0x00)
        data = spi.SPI_read_byte()
        spi.SPI_write_byte(self.CS, 0x00)
        data = data + [spi.SPI_read_byte()]
        print data                      # return speed in real units


    def Move(self, units):
        ' Move some distance units from current position '
        steps = units * self.SPU  # translate units to steps 
        if steps > 0:                                          # look for direction
            spi.SPI_write_byte(self.CS, 0x40 | (~self.Dir & 1))       
        else:
            spi.SPI_write_byte(self.CS, 0x40 | (self.Dir & 1)) 
        steps = int(abs(steps))     
        spi.SPI_write_byte(self.CS, (steps >> 16) & 0xFF)
        spi.SPI_write_byte(self.CS, (steps >> 8) & 0xFF)
        spi.SPI_write_byte(self.CS, steps & 0xFF)

    def Run(self, direction, speed):
        speed_value = int(speed / 0.015)

        command = 0b01010000 + int(direction)  
        data = [(speed_value >> i & 0xff) for i in (16,8,0)]
        spi.SPI_write_byte(self.CS, command)       # Max Speed setup 
        spi.SPI_write_byte(self.CS, data[0])
        spi.SPI_write_byte(self.CS, data[1])  
        spi.SPI_write_byte(self.CS, data[2])
        return (speed_value * 0.015)

    def MoveWait(self, units):
        ' Move some distance units from current position and wait for execution '
        self.Move(units)
        while self.GetStatus()['BUSY']:
            time.sleep(0.1)

    def Float(self, hard = False):
        ' switch H-bridge to High impedance state '
        if (hard == False):
            spi.SPI_write_byte(self.CS, 0xA0)
        else:
            spi.SPI_write_byte(self.CS, 0xA8)


# End Class axis --------------------------------------------------


print "Clock motor control script started. \r\n"
print "Requested speed is: %f steps/s" % SPEED

pylirc.init("pylirc", "/home/odroid/conf")



cfg = config.Config(
    i2c = {
        "port": 1,
    },

    bus = [
        { 
        "name":"spi", 
        "type":"i2cspi", 
        "address": 0x2e,
        },
    ],
)


cfg.initialize()

spi = cfg.get_device("spi")

spi.route()


try:
    print "Configuring SPI.."
    spi.SPI_config(spi.I2CSPI_MSB_FIRST| spi.I2CSPI_MODE_CLK_IDLE_HIGH_DATA_EDGE_TRAILING| spi.I2CSPI_CLK_461kHz)
    time.sleep(0.1)

    maximum_speed = 2 * SPEED

    print "Configuring stepper motor.."
    X = axis(spi.I2CSPI_SS0, 0, 1, MaxSpeed = maximum_speed)    # set Number of Steps per axis Unit and set Direction of Rotation


    print "Motor speed limit is: %f steps/s" % maximum_speed
    running = False

    print "Waiting for IR command.."
    while True:                    # set maximal motor speed 
        key = pylirc.nextcode()     ## preccessing the IR remote control commands.

        if key == ['start']:
            running =  True
            direction = True
            requested_speed = SPEED

        if key == ['faster']:
            running =  True
            direction = True
            requested_speed = SPEED * 1.2      # runnig the motor at 120% of the base motor speed

        if key == ['slower']:
            running =  True
            direction = False
            requested_speed = SPEED * 0.8

        if key == ['stop']:
            running =  False

        time.sleep(0.1)

        if running == True:
            real_speed = X.Run(direction, requested_speed)
            print "Motor running at: %f steps/s" % real_speed
        else:
            X.Float(hard=False)   # release power
            X.Reset()
            X.Initialize()
            print "Stopping the motor."

except KeyboardInterrupt:
    print "stop"
    X.Float(hard=False)   # release power
    sys.exit(0)

except Exception, e:
    X.Float(hard=False)   # release power
    print >> sys.stderr, "Exception: %s" % str(e)
    sys.exit(1)