# generated by Slic3r 1.2.9 on Fri Jul 31 14:56:23 2015

[filament:ABS_1.75]
bed_temperature = 90
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 1.01
fan_always_on = 0
fan_below_layer_time = 1
filament_diameter = 1.75
first_layer_bed_temperature = 90
first_layer_temperature = 225
max_fan_speed = 0
min_fan_speed = 0
min_print_speed = 15
slowdown_below_layer_time = 20
temperature = 225

[filament:ABS_1.75 3D factories]
bed_temperature = 90
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 5
filament_diameter = 1.75
first_layer_bed_temperature = 90
first_layer_temperature = 225
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 15
slowdown_below_layer_time = 20
temperature = 225

[filament:ABS_1.75 red 3D factories]
bed_temperature = 90
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 5
filament_diameter = 1.73
first_layer_bed_temperature = 80
first_layer_temperature = 230
max_fan_speed = 60
min_fan_speed = 0
min_print_speed = 15
slowdown_below_layer_time = 20
temperature = 225

[filament:PLA_1.75]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 1
filament_diameter = 1.74
first_layer_bed_temperature = 60
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 15
slowdown_below_layer_time = 20
temperature = 210

[filament:PLA_1.75 3D factories]
bed_temperature = 50
bridge_fan_speed = 50
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 0.9524
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 60
first_layer_temperature = 185
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 185

[filament:PLA_1.75 _Mladec_green]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 60
first_layer_temperature = 210
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 210

[filament:Simple Mode]
bed_temperature = 110
extrusion_multiplier = 1
filament_diameter = 1.75
first_layer_bed_temperature = 115
first_layer_temperature = 235
temperature = 230

[filament:config]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 1.75
first_layer_bed_temperature = 60
first_layer_temperature = 212
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 30
temperature = 212

[filament:slic3r_config]
bed_temperature = 90
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 0.95
fan_always_on = 0
fan_below_layer_time = 5
filament_diameter = 1.75
first_layer_bed_temperature = 80
first_layer_temperature = 230
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 15
slowdown_below_layer_time = 20
temperature = 230

[presets]
filament = pad_config.ini
print = pad_config.ini
printer = pad_config.ini

[print:0.2 layer]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 15
brim_width = 10
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 15%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.2
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 1
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 4
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[print:0.3 layer]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 10
brim_width = 2
complete_objects = 1
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 50%
fill_pattern = rectilinear
first_layer_acceleration = 500
first_layer_extrusion_width = 180%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 10
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[print:0.3 layer brim]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 3000
bridge_flow_ratio = 1
bridge_speed = 10
brim_width = 10
complete_objects = 0
default_acceleration = 4000
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.6
fill_angle = 45
fill_density = 25%
fill_pattern = line
first_layer_acceleration = 0
first_layer_extrusion_width = 180%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 15
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[print:ABS 1.75]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1.9
bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 40%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.2
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130

[print:ABS_rocket]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 500
bridge_flow_ratio = 1.9
bridge_speed = 60
brim_width = 15
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.5
fill_angle = 45
fill_density = 40%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[print:ABS_vase]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 500
bridge_flow_ratio = 1.9
bridge_speed = 60
brim_width = 5
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 0%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 120%
first_layer_height = 0.3
first_layer_speed = 30%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 1
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 1
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 0
travel_speed = 130
xy_size_compensation = 0

[print:Bridge]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 3000
bridge_flow_ratio = 1
bridge_speed = 10
brim_width = 5
complete_objects = 0
default_acceleration = 4000
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.6
fill_angle = 45
fill_density = 25%
fill_pattern = line
first_layer_acceleration = 0
first_layer_extrusion_width = 125%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = random
skirt_distance = 10
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 100

[print:Simple Mode]
bottom_solid_layers = 3
brim_width = 0
complete_objects = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
fill_density = 40%
fill_pattern = honeycomb
infill_speed = 60
layer_height = 0.2
perimeter_speed = 30
perimeters = 3
raft_layers = 0
support_material = 0
support_material_spacing = 2.5
top_solid_layers = 3
travel_speed = 130

[print:Standard]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
bridge_speed = 20
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.6
fill_angle = 45
fill_density = 25%
fill_pattern = line
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 4
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130

[print:Weather_screen]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 3000
bridge_flow_ratio = 1
bridge_speed = 10
brim_width = 5
complete_objects = 0
default_acceleration = 4000
dont_support_bridges = 1
external_fill_pattern = concentric
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.6
fill_angle = 45
fill_density = 90%
fill_pattern = concentric
first_layer_acceleration = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 5
skirt_height = 1
skirts = 0
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130

[print:barb_print_config]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 5
brim_width = 0
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 20%
fill_pattern = concentric
first_layer_acceleration = 500
first_layer_extrusion_width = 180%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 10
skirt_height = 1
skirts = 1
small_perimeter_speed = 10
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear-grid
support_material_spacing = 3
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[print:config]
avoid_crossing_perimeters = 1
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 5
brim_width = 0
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = concentric
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 1%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 180%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.3
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 1
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 10
skirt_height = 1
skirts = 2
small_perimeter_speed = 30
solid_infill_below_area = 50
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[print:config_gears]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 5
brim_width = 0
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 15%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 180%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.3
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 10
skirt_height = 1
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[print:engine_config]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 5
brim_width = 0
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = concentric
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 1%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 180%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.3
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 1
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 10
skirt_height = 1
skirts = 2
small_perimeter_speed = 30
solid_infill_below_area = 50
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[print:engine_nozzle_config]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 5
brim_width = 0
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = concentric
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 40%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 180%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 10
skirt_height = 1
skirts = 2
small_perimeter_speed = 30
solid_infill_below_area = 50
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 6
travel_speed = 130
xy_size_compensation = 0

[print:holder_print_config]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 5
brim_width = 0
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 10%
fill_pattern = rectilinear
first_layer_acceleration = 500
first_layer_extrusion_width = 180%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.3
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 1
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 10
skirt_height = 1
skirts = 1
small_perimeter_speed = 10
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[print:pad_config]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 15
brim_width = 0
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 15%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 1
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 4
skirt_height = 1
skirts = 2
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[print:slic3r_config]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_flow_ratio = 1
bridge_speed = 15
brim_width = 0
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 15%
fill_pattern = honeycomb
first_layer_acceleration = 500
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 60%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_height = 0.2
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 1
post_process = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 4
skirt_height = 1
skirts = 2
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
thin_walls = 1
threads = 2
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
xy_size_compensation = 0

[printer:RebeliX]
bed_shape = 0x0,180x0,180x180,0x180
before_layer_gcode = 
end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84     ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = B14197D3716442D4B0BB8F485877E31E
octoprint_host = 192.168.1.106:5000
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1.3
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 60
start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
z_offset = 0

[printer:Simple Mode]
bed_shape = 0x0,180x0,180x180,0x180
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
gcode_flavor = reprap
nozzle_diameter = 0.3
retract_length = 1
retract_lift = 0
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
z_offset = 0

[printer:engine_config]
bed_shape = 0x0,180x0,180x180,0x180
before_layer_gcode = 
end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84     ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 330CC1C393FC4CD08C420E476D472A7E
octoprint_host = 192.168.1.25
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 1.3
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 60
start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:pad_config]
bed_shape = 0x0,180x0,180x180,0x180
before_layer_gcode = 
end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84     ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 330CC1C393FC4CD08C420E476D472A7E
octoprint_host = 192.168.1.25
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1.3
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 60
start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0

[printer:slic3r_config]
bed_shape = 0x0,180x0,180x180,0x180
before_layer_gcode = 
end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84     ; disable motors\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.4
octoprint_apikey = 330CC1C393FC4CD08C420E476D472A7E
octoprint_host = 192.168.1.25
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1.3
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 60
start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
z_offset = 0

[settings]
autocenter = 1
mode = expert

[simple]
avoid_crossing_perimeters = 1
bed_shape = 0x0,180x0,180x180,0x180
bed_temperature = 110
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
external_fill_pattern = rectilinear
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 1.75
fill_angle = 45
fill_density = 40%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 115
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 30%
first_layer_temperature = 235
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 10
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
interface_shells = 0
layer_gcode = 
layer_height = 0.2
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 0
notes = 
nozzle_diameter = 0.3
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 3
post_process = 
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 30
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
temperature = 230
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
use_firmware_retraction = 0
use_relative_e_distances = 0
vibration_limit = 0
wipe = 0
z_offset = 0