pedestal_height = 13;
mount_hole = 3.5;
clear = 0.175;
nut_size = 6.6;

module ramp(width, depth, height) {
    angle = atan(height / depth);
    
    difference () {
        cube([width, depth, height]);
    
        //color("red")
        rotate([angle, 0, 0])
        translate([-1, 0, 0])
        cube([width + 2, depth * 2, height]);
    }
}

difference () {
//        translate ([-1,-16,0])
        cube([50,100,pedestal_height]);

        //mount holes for ODROID U3
        translate ([4.5,4.5 + 76, 0])
        rotate([0,0,90])
        cylinder (h = 6 ,r= nut_size/2 + clear, $fn=6);
        translate ([4.5,4.5 + 76, 6.2])
        cylinder (h = pedestal_height, r= mount_hole/2, $fn=10);
    
        translate ([4.5 + 41, 4.5 + 76,0])
        rotate([0,0,90])
        cylinder (h = 6,r= nut_size/2 + clear, $fn=6);
        translate ([4.5 + 41, 4.5 + 76, 6.2])
        cylinder (h = pedestal_height, r= mount_hole/2, $fn=10);


/// Two holes for other side of ODROID-U3 PCB. 
        translate ([4.5,4.5,0])
        cylinder (h = 6, r= (nut_size+clear)/2, $fn=6);
        translate ([4.5,4.5,6.2])
        cylinder (h = pedestal_height, r= mount_hole/2, $fn=10);
    
        translate ([4.5+41,4.5,0])
        cylinder (h = 6, r= (nut_size+clear)/2, $fn=6);
        translate ([4.5+41,4.5,6.2])
        cylinder (h = pedestal_height, r= mount_hole/2, $fn=10);

// MLAB grid holes

        for (j = [1 : 3], i = [0 : 0]) {
                translate ([4.5 + j*10.16, 4.5 + i*10.16,0])
                cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
                translate ([4.5 + j*10.16, 4.5 + i*10.16, 3.2])  // one solid layer for slicer (the holes will be pierced on demand )
                cylinder (h = pedestal_height /3, r= mount_hole/2, $fn=10);
                translate ([4.5 + j*10.16, 4.5 + i*10.16, 6.3])
                cylinder (h = 10, r= nut_size/2, $fn=6);
        }


        for (j = [0 : 7], i = [1 : 6]) {
                translate ([4.5 + j*10.16, 4.5 + i*10.16,0])
                cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
                translate ([4.5 + j*10.16, 4.5 + i*10.16, 3.2])  // one solid layer for slicer (the holes will be pierced on demand )
                cylinder (h = pedestal_height /3, r= mount_hole/2, $fn=10);
                translate ([4.5 + j*10.16, 4.5 + i*10.16, 6.3])
                cylinder (h = 10, r= nut_size/2, $fn=6);
        }

        ////////////////////////////////////
        translate ([4,6, pedestal_height - 4])  // ODROIDs passive components hole. 
        cube([42,27,5]);
        translate ([13, 2 , pedestal_height - 4])  // two small resistors on botom side.
        cube([3,3,5]);
        translate ([22, 30 , pedestal_height - 4])  // USB over voltage protection.
        cube([21,5,5]);
        
        
        translate ([0, 41 , pedestal_height - 3.5]) // HOLE for ODROD's , SD card and eMMC.
        cube([48,32,5]);
        translate ([0, 38.5 , pedestal_height - 4.5]) // HOLE for ODROD's jack connector
        cube([14,8,5]);
        translate ([0, 65 , pedestal_height - 3.5]) // HOLE for ODROD's , SD card and eMMC.
        cube([17,13,5]);

        ////////////////////////////////////////
        
////  lightening central holes
        
        translate ([10,10, 0])  // ODROIDs passive components hole. 
        cube([30,19.5,pedestal_height ]);        
        
        translate ([10,41, 0])  // ODROIDs passive components hole. 
        cube([30,30,pedestal_height ]);        
        
//////   
//      MLAB electrical adapter part
///////
difference () {
        translate ([8,74.9,pedestal_height - 11])       // Central mount hole
        cube([34,17.1,pedestal_height - 8.5]);
        translate ([25,85.78,0])
        cylinder (h = 30, r= nut_size*0.7, $fn=20);
}

        translate ([0,84, pedestal_height - 8.5])       // Holes for MLAB's adapter 5V power connector.
        cube([50,20,20]);

        translate ([42,84,pedestal_height - 11])        // Holes for MLAB's adapter 5V power connector.
        cube([34,8,pedestal_height - 8.5]);

        translate ([8,92,pedestal_height - 11]) // Holes for MLAB's adapter IO connectors.
        cube([34,8,pedestal_height - 8.5]);

 
        translate ([0,74.9, pedestal_height - 8.5])     // Hole for MLAB  PCB
        cube([50,25.1,2]);
        translate ([7.5,78,pedestal_height - 8.5])      // Hole For connectors above the adapter PCB
        cube([35.5,17.1,10]);

        translate ([0,74.9, pedestal_height - 6.5])
        ramp(50, 50, 25);
/////// Elecrical adapter PCB mount holes

        translate ([25,85.78,0])
        cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
        translate ([25,85.78,3.2])
        cylinder (h = pedestal_height + clear,r= mount_hole/2, $fn=10);

        translate ([4.68,85.78 + 10.16,0])
        cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
        translate ([4.68,85.78 + 10.16,3.2])
        cylinder (h = pedestal_height + clear,r= mount_hole/2, $fn=10);

        translate ([45.32,85.78 + 10.16,0])
        cylinder (h = 3, r= (nut_size+clear)/2, $fn=6);
        translate ([45.32,85.78 + 10.16,3.2])
        cylinder (h = pedestal_height + clear,r= mount_hole/2, $fn=10);

}


/// Support material
/*
        color("Blue",0.5)
        //translate ([0,74.9, pedestal_height - 8.5])   // Hole for MLAB  PCB
        cube([50,70,30]);
*/