//************************************************************************//**//** Project......: Firmware USB AVR Si570 controler.//**//** Platform.....: ATtiny45 @ 16.5 MHz//**//** Licence......: This software is freely available for non-commercial//** use - i.e. for research and experimentation only!//**//** Programmer...: F.W. Krom, PE0FKO//**//** Description..: USB commando codes//**//** History......: V15.12: First version//**//**************************************************************************////#define CMD_ECHO_WORD 0x00#define CMD_GET_VERSION 0x00#define CMD_SET_DDR 0x01#define CMD_GET_PIN 0x02#define CMD_GET_PORT 0x03#define CMD_SET_PORT 0x04// 0x05 // Used in old V1.4// 0x06 // Used in old V1.4// 0x07 // Used in old V1.4// 0x08 // Used in old V1.4// 0x09 // Used in old V1.4// 0x0A // Used in old V1.4// 0x0B // Used in old V1.4// 0x0C // Used in old V1.4#define CMD_REBOOT 0x0F// 0x10 // Used in old V1.4// 0x11 // Used in old V1.4#define CMD_SET_IO 0x15#define CMD_GET_IO 0x16#define CMD_SET_FILTER 0x17#define CMD_SET_RX_BAND_FILTER 0x18 // V15.12#define CMD_GET_RX_BAND_FILTER 0x19 // V15.12#define CMD_SET_TX_BAND_FILTER 0x1A // MOBO Only#define CMD_GET_TX_BAND_FILTER 0x1B // MOBO Only#define CMD_SET_SI570 0x20 // Write byte to Si570 register// 0x21 // Used in old V1.4// 0x22 // Used in old V1.4// 0x23 // Used in old V1.4#define CMD_SET_FREQ_REG 0x30#define CMD_SET_LO_SM 0x31#define CMD_SET_FREQ 0x32#define CMD_SET_XTAL 0x33#define CMD_SET_STARTUP 0x34#define CMD_SET_PPM 0x35// 0x36 // Used in old V2.0// 0x37 // Used in old V2.0// 0x38 // Used in old V2.0#define CMD_GET_LO_SM 0x39#define CMD_GET_FREQ 0x3a#define CMD_GET_PPM 0x3b#define CMD_GET_STARTUP 0x3c#define CMD_GET_XTAL 0x3d#define CMD_GET_REGS 0x3e#define CMD_GET_SI570 0x3f#define CMD_GET_I2C_ERR 0x40#define CMD_SET_I2C_ADDR 0x41#define CMD_GET_CPU_TEMP 0x42 //#define CMD_SET_USRP1 0x50#define CMD_GET_CW_KEY 0x51// 0x52 // Used in old V2.0// 0x53 // Used in old V2.0// 0x54 // Used in old V2.0// Mobo command's#define CMD_GET_FW_FEATURE 0x60 // Firmware Feature select#define CMD_GET_ADC_INPUTS 0x61 // Read analog inputs (Temp, PA current, P_out, P_ref, Vdd)#define CMD_RM_PA_HIGH_TEMP 0x64 // Read/Modify the PA High Temperature limit#define CMD_RM_PA_BIAS 0x65 // Read/Modify PA bias setting related values, 5 items#define CMD_RM_PA_SWR 0x66 // Read/Modify SWR measurement and SWR alarm related values 4 items#define CMD_RM_ROTARY 0x67 // Read/Modify Rotatry Encoder Resolution#define CMD_SET_BYTE_GPIO 0x6e // Write a Byte to (PCF8584) GPIO Extender#define CMD_GET_BYTE_GPIO 0x6f // Read a Byte from (PCF8584) GPIO Extender// 0xEE // Used in old V2.0// 0xEF // Used in old V2.0// 0xFF // Used in old V2.0