$fn=40; // model faces resolution.
include <../configuration.scad>
include <polyScrewThread_r1.scad>




difference () {
AWSCREEN01A_D02(D03_vyska_zavitu,D03_tolerance_zavitu,D03_material_za_zavitem,D03_polomer_zavitu,D03_polomer_stitu,D03_tloustka_materialu,3*D03_vyska_zavitu,D03_pocet_vyztuh,screen_bevel);


cube([180,180,180]);

    }





module AWSCREEN01A_D02(D03_vyska_zavitu,D03_tolerance_zavitu,D03_material_za_zavitem,D03_polomer_zavitu,D03_polomer_stitu,D03_tloustka_materialu,D03_vyska_stitu,D03_pocet_vyztuh,screen_bevel)

    {
    angle_sep = 360/D03_pocet_vyztuh;

//spodní kruh
difference () {
        cylinder (h=3*D03_tloustka_materialu,r = D03_polomer_stitu,$fn=100);
    translate ([0,0,-0.005])
        cylinder (h=2*D03_tloustka_materialu+0.01,r = D03_polomer_stitu-D03_tloustka_materialu,$fn=100);
                 
    translate ([0,0,3*D03_tloustka_materialu])
            translate ([0,0,-D03_tloustka_materialu-0.01/2])
            cylinder (h=D03_vyska_stitu-3*D03_tloustka_materialu-0.4,r1=D03_polomer_stitu ,r2=D03_polomer_zavitu,$fn=100);
    
       
                    }
    
//spodní kruh - kvůli doplnění výkroje
difference () {
    
    
        cylinder (h=3*D03_tloustka_materialu,r = D03_polomer_stitu,$fn=100);
    translate ([0,0,-0.005])
        cylinder (h=3*D03_tloustka_materialu+0.01,r = D03_polomer_stitu-D03_tloustka_materialu,$fn=100);
                 
             
    
                    }         
                    



   



//screen - velky kuzel
    
     translate ([0,0,3*D03_tloustka_materialu])
    difference () {
        cylinder (h=D03_vyska_stitu-3*D03_tloustka_materialu,r1=D03_polomer_stitu ,r2=D03_polomer_zavitu,$fn=100);
        translate ([0,0,-D03_tloustka_materialu-0.01/2])
            cylinder (h=D03_vyska_stitu-3*D03_tloustka_materialu-0.4,r1=D03_polomer_stitu ,r2=D03_polomer_zavitu,$fn=100);
    
       
                    }
                    
                    //horni kuzel
    
     translate ([0,0,D03_vyska_stitu-0.01])
   
        cylinder (h=5,r1=D03_polomer_zavitu ,r2=1,$fn=100);
        


//inner ring


    difference () {
        cylinder (h=D03_vyska_zavitu,r = D03_polomer_zavitu + D03_material_za_zavitem/2,$fn=100);
        translate([0,0,-1])
                screw_thread(D03_polomer_zavitu*2,4,55,D03_vyska_zavitu+2,PI/2,2);  
                    }


// center ribs
for (i = [0 : (D03_pocet_vyztuh-1)]) {
        rotate ([90,0,angle_sep* i])
        translate ([0,0,-D03_tloustka_materialu/2])
        linear_extrude (height = D03_tloustka_materialu, convexity = 10)
        polygon(points=[[D03_polomer_zavitu,D03_vyska_stitu+0.01],[D03_polomer_zavitu, 0],[D03_polomer_stitu - D03_tloustka_materialu+0.01,0],[D03_polomer_stitu- D03_tloustka_materialu+0.01,3*D03_tloustka_materialu]]);

}
}