# generated by Slic3r 1.3.0-dev on Wed Jun 15 18:12:58 2016
avoid_crossing_perimeters = 0
bed_shape = 0x0,180x0,180x180,0x180
bed_temperature = 50
before_layer_gcode = 
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 5
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 500
disable_fan_first_layers = 1
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M104 S0 ; turn off nozzle\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nG1 Y170 F3000 ; move the print to the front\nM84     ; disable motors\n
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 1.75
filament_settings_id = 
fill_angle = 45
fill_density = 10%
fill_pattern = rectilinear
first_layer_acceleration = 500
first_layer_bed_temperature = 60
first_layer_extrusion_width = 180%
first_layer_height = 0.3
first_layer_speed = 60%
first_layer_temperature = 212
gap_fill_speed = 10
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 60
interface_shells = 0
layer_gcode = 
layer_height = 0.3
max_fan_speed = 100
max_print_speed = 80
max_volumetric_speed = 0
min_fan_speed = 100
min_print_speed = 10
min_skirt_length = 0
notes = 
nozzle_diameter = 0.4
octoprint_apikey = A7268185315B4A8B9CA2C16415AC5F1F
octoprint_host = 10.1.1.119:80
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 500
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 1
post_process = 
pressure_advance = 0
print_settings_id = 
printer_settings_id = 
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1.3
retract_length_toolchange = 3
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 60
seam_position = aligned
serial_port = 
serial_speed = 250000
skirt_distance = 10
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 30
small_perimeter_speed = 10
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 55
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home all axes\nG92 E0.0 ; reset extruder
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
temperature = 212
thin_walls = 1
threads = 4
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
xy_size_compensation = 0
z_offset = 0