/*--------------------------------------------------------------------------/
/  FatFs - FAT file system module include file  R0.06        (C)ChaN, 2008
/---------------------------------------------------------------------------/
/ FatFs module is an experimenal project to implement FAT file system to
/ cheap microcontrollers. This is a free software and is opened for education,
/ research and development under license policy of following trems.
/
/  Copyright (C) 2008, ChaN, all right reserved.
/
/ * The FatFs module is a free software and there is no warranty.
/ * You can use, modify and/or redistribute it for personal, non-profit or
/   commercial use without any restriction under your responsibility.
/ * Redistributions of source code must retain the above copyright notice.
/
/---------------------------------------------------------------------------*/

#ifndef _FATFS

#define _MCU_ENDIAN             0
/* The _MCU_ENDIAN defines which access method is used to the FAT structure.
/  1: Enable word access.
/  2: Disable word access and use byte-by-byte access instead.
/  When the architectural byte order of the MCU is big-endian and/or address
/  miss-aligned access results incorrect behavior, the _MCU_ENDIAN must be set to 2.
/  If it is not the case, it can also be set to 1 for good code efficiency. */

#define _FS_READONLY    0
/* Setting _FS_READONLY to 1 defines read only configuration. This removes
/  writing functions, f_write, f_sync, f_unlink, f_mkdir, f_chmod, f_rename,
/  f_truncate and useless f_getfree. */

#define _FS_MINIMIZE    0
/* The _FS_MINIMIZE option defines minimization level to remove some functions.
/  0: Full function.
/  1: f_stat, f_getfree, f_unlink, f_mkdir, f_chmod, f_truncate and f_rename are removed.
/  2: f_opendir and f_readdir are removed in addition to level 1.
/  3: f_lseek is removed in addition to level 2. */

#define _USE_STRFUNC    0
/* To enable string functions, set _USE_STRFUNC to 1 or 2. */

#define _USE_MKFS       0
/* When _USE_MKFS is set to 1 and _FS_READONLY is set to 0, f_mkfs function is
/  enabled. */

#define _DRIVES         2
/* Number of logical drives to be used. This affects the size of internal table. */

#define _MULTI_PARTITION        0
/* When _MULTI_PARTITION is set to 0, each logical drive is bound to same
/  physical drive number and can mount only 1st primaly partition. When it is
/  set to 1, each logical drive can mount a partition listed in Drives[]. */

#define _USE_FSINFO     0
/* To enable FSInfo support on FAT32 volume, set _USE_FSINFO to 1. */

#define _USE_SJIS       1
/* When _USE_SJIS is set to 1, Shift-JIS code transparency is enabled, otherwise
/  only US-ASCII(7bit) code can be accepted as file/directory name. */

#define _USE_NTFLAG     1
/* When _USE_NTFLAG is set to 1, upper/lower case of the file name is preserved.
/  Note that the files are always accessed in case insensitive. */


#include "integer.h"



/* Definitions corresponds to multiple sector size (not tested) */
#define S_MAX_SIZ       512U                    /* Do not change */
#if S_MAX_SIZ > 512U
#define SS(fs)  ((fs)->s_size)
#else
#define SS(fs)  512U
#endif


/* File system object structure */
typedef struct _FATFS {
        WORD    id;                             /* File system mount ID */
        WORD    n_rootdir;              /* Number of root directory entries */
        DWORD   winsect;                /* Current sector appearing in the win[] */
        DWORD   sects_fat;              /* Sectors per fat */
        DWORD   max_clust;              /* Maximum cluster# + 1 */
        DWORD   fatbase;                /* FAT start sector */
        DWORD   dirbase;                /* Root directory start sector (cluster# for FAT32) */
        DWORD   database;               /* Data start sector */
#if !_FS_READONLY
        DWORD   last_clust;             /* Last allocated cluster */
        DWORD   free_clust;             /* Number of free clusters */
#if _USE_FSINFO
        DWORD   fsi_sector;             /* fsinfo sector */
        BYTE    fsi_flag;               /* fsinfo dirty flag (1:must be written back) */
        BYTE    pad2;
#endif
#endif
        BYTE    fs_type;                /* FAT sub type */
        BYTE    csize;                  /* Number of sectors per cluster */
#if S_MAX_SIZ > 512U
        WORD    s_size;                 /* Sector size */
#endif
        BYTE    n_fats;                 /* Number of FAT copies */
        BYTE    drive;                  /* Physical drive number */
        BYTE    winflag;                /* win[] dirty flag (1:must be written back) */
        BYTE    pad1;
        BYTE    win[S_MAX_SIZ]; /* Disk access window for Directory/FAT */
} FATFS;


/* Directory object structure */
typedef struct _DIR {
        WORD    id;                     /* Owner file system mount ID */
        WORD    index;          /* Current index */
        FATFS*  fs;                     /* Pointer to the owner file system object */
        DWORD   sclust;         /* Start cluster */
        DWORD   clust;          /* Current cluster */
        DWORD   sect;           /* Current sector */
} DIR;


/* File object structure */
typedef struct _FIL {
        WORD    id;                             /* Owner file system mount ID */
        BYTE    flag;                   /* File status flags */
        BYTE    csect;                  /* Sector address in the cluster */
        FATFS*  fs;                             /* Pointer to the owner file system object */
        DWORD   fptr;                   /* File R/W pointer */
        DWORD   fsize;                  /* File size */
        DWORD   org_clust;              /* File start cluster */
        DWORD   curr_clust;             /* Current cluster */
        DWORD   curr_sect;              /* Current sector */
#if _FS_READONLY == 0
        DWORD   dir_sect;               /* Sector containing the directory entry */
        BYTE*   dir_ptr;                /* Ponter to the directory entry in the window */
#endif
        BYTE    buffer[S_MAX_SIZ];      /* File R/W buffer */
} FIL;


/* File status structure */
typedef struct _FILINFO {
        DWORD fsize;                    /* Size */
        WORD fdate;                             /* Date */
        WORD ftime;                             /* Time */
        BYTE fattrib;                   /* Attribute */
        char fname[8+1+3+1];    /* Name (8.3 format) */
} FILINFO;



/* Definitions corresponds to multi partition */

#if _MULTI_PARTITION != 0       /* Multiple partition cfg */

typedef struct _PARTITION {
        BYTE pd;        /* Physical drive # (0-255) */
        BYTE pt;        /* Partition # (0-3) */
} PARTITION;
extern
const PARTITION Drives[];                       /* Logical drive# to physical location conversion table */
#define LD2PD(drv) (Drives[drv].pd)     /* Get physical drive# */
#define LD2PT(drv) (Drives[drv].pt)     /* Get partition# */

#else                                           /* Single partition cfg */

#define LD2PD(drv) (drv)                /* Physical drive# is equal to logical drive# */
#define LD2PT(drv) 0                    /* Always mounts the 1st partition */

#endif


/* File function return code (FRESULT) */

typedef enum {
        FR_OK = 0,                      /* 0 */
        FR_NOT_READY,           /* 1 */
        FR_NO_FILE,                     /* 2 */
        FR_NO_PATH,                     /* 3 */
        FR_INVALID_NAME,        /* 4 */
        FR_INVALID_DRIVE,       /* 5 */
        FR_DENIED,                      /* 6 */
        FR_EXIST,                       /* 7 */
        FR_RW_ERROR,            /* 8 */
        FR_WRITE_PROTECTED,     /* 9 */
        FR_NOT_ENABLED,         /* 10 */
        FR_NO_FILESYSTEM,       /* 11 */
        FR_INVALID_OBJECT,      /* 12 */
        FR_MKFS_ABORTED         /* 13 */
} FRESULT;



/*-----------------------------------------------------*/
/* FatFs module application interface                  */

FRESULT f_mount (BYTE, FATFS*);                                         /* Mount/Unmount a logical drive */
FRESULT f_open (FIL*, const char*, BYTE);                       /* Open or create a file */
FRESULT f_read (FIL*, void*, UINT, UINT*);                      /* Read data from a file */
FRESULT f_write (FIL*, const void*, UINT, UINT*);       /* Write data to a file */
FRESULT f_lseek (FIL*, DWORD);                                          /* Move file pointer of a file object */
FRESULT f_close (FIL*);                                                         /* Close an open file object */
FRESULT f_opendir (DIR*, const char*);                          /* Open an existing directory */
FRESULT f_readdir (DIR*, FILINFO*);                                     /* Read a directory item */
FRESULT f_stat (const char*, FILINFO*);                         /* Get file status */
FRESULT f_getfree (const char*, DWORD*, FATFS**);       /* Get number of free clusters on the drive */
FRESULT f_truncate (FIL*);                                                      /* Truncate file */
FRESULT f_sync (FIL*);                                                          /* Flush cached data of a writing file */
FRESULT f_unlink (const char*);                                         /* Delete an existing file or directory */
FRESULT f_mkdir (const char*);                                          /* Create a new directory */
FRESULT f_chmod (const char*, BYTE, BYTE);                      /* Change file/dir attriburte */
FRESULT f_utime (const char*, const FILINFO*);          /* Change file/dir timestamp */
FRESULT f_rename (const char*, const char*);            /* Rename/Move a file or directory */
FRESULT f_mkfs (BYTE, BYTE, WORD);                                      /* Create a file system on the drive */
#if _USE_STRFUNC
#define feof(fp) ((fp)->fptr == (fp)->fsize)
#define EOF -1
int fputc (int, FIL*);                                                          /* Put a character to the file */
int fputs (const char*, FIL*);                                          /* Put a string to the file */
int fprintf (FIL*, const char*, ...);                           /* Put a formatted string to the file */
char* fgets (char*, int, FIL*);                                         /* Get a string from the file */
#endif

/* User defined function to give a current time to fatfs module */

DWORD get_fattime (void);       /* 31-25: Year(0-127 org.1980), 24-21: Month(1-12), 20-16: Day(1-31) */
                                                        /* 15-11: Hour(0-23), 10-5: Minute(0-59), 4-0: Second(0-29 *2) */



/* File access control and file status flags (FIL.flag) */

#define FA_READ                         0x01
#define FA_OPEN_EXISTING        0x00
#if _FS_READONLY == 0
#define FA_WRITE                        0x02
#define FA_CREATE_NEW           0x04
#define FA_CREATE_ALWAYS        0x08
#define FA_OPEN_ALWAYS          0x10
#define FA__WRITTEN                     0x20
#define FA__DIRTY                       0x40
#endif
#define FA__ERROR                       0x80


/* FAT sub type (FATFS.fs_type) */

#define FS_FAT12        1
#define FS_FAT16        2
#define FS_FAT32        3


/* File attribute bits for directory entry */

#define AM_RDO  0x01    /* Read only */
#define AM_HID  0x02    /* Hidden */
#define AM_SYS  0x04    /* System */
#define AM_VOL  0x08    /* Volume label */
#define AM_LFN  0x0F    /* LFN entry */
#define AM_DIR  0x10    /* Directory */
#define AM_ARC  0x20    /* Archive */



/* Offset of FAT structure members */

#define BS_jmpBoot                      0
#define BS_OEMName                      3
#define BPB_BytsPerSec          11
#define BPB_SecPerClus          13
#define BPB_RsvdSecCnt          14
#define BPB_NumFATs                     16
#define BPB_RootEntCnt          17
#define BPB_TotSec16            19
#define BPB_Media                       21
#define BPB_FATSz16                     22
#define BPB_SecPerTrk           24
#define BPB_NumHeads            26
#define BPB_HiddSec                     28
#define BPB_TotSec32            32
#define BS_55AA                         510

#define BS_DrvNum                       36
#define BS_BootSig                      38
#define BS_VolID                        39
#define BS_VolLab                       43
#define BS_FilSysType           54

#define BPB_FATSz32                     36
#define BPB_ExtFlags            40
#define BPB_FSVer                       42
#define BPB_RootClus            44
#define BPB_FSInfo                      48
#define BPB_BkBootSec           50
#define BS_DrvNum32                     64
#define BS_BootSig32            66
#define BS_VolID32                      67
#define BS_VolLab32                     71
#define BS_FilSysType32         82

#define FSI_LeadSig                     0
#define FSI_StrucSig            484
#define FSI_Free_Count          488
#define FSI_Nxt_Free            492

#define MBR_Table                       446

#define DIR_Name                        0
#define DIR_Attr                        11
#define DIR_NTres                       12
#define DIR_CrtTime                     14
#define DIR_CrtDate                     16
#define DIR_FstClusHI           20
#define DIR_WrtTime                     22
#define DIR_WrtDate                     24
#define DIR_FstClusLO           26
#define DIR_FileSize            28



/* Multi-byte word access macros  */

#if _MCU_ENDIAN == 1    /* Use word access */
#define LD_WORD(ptr)            (WORD)(*(WORD*)(BYTE*)(ptr))
#define LD_DWORD(ptr)           (DWORD)(*(DWORD*)(BYTE*)(ptr))
#define ST_WORD(ptr,val)        *(WORD*)(BYTE*)(ptr)=(WORD)(val)
#define ST_DWORD(ptr,val)       *(DWORD*)(BYTE*)(ptr)=(DWORD)(val)
#elif _MCU_ENDIAN == 2  /* Use byte-by-byte access */
#define LD_WORD(ptr)            (WORD)(((WORD)*(volatile BYTE*)((ptr)+1)<<8)|(WORD)*(volatile BYTE*)(ptr))
#define LD_DWORD(ptr)           (DWORD)(((DWORD)*(volatile BYTE*)((ptr)+3)<<24)|((DWORD)*(volatile BYTE*)((ptr)+2)<<16)|((WORD)*(volatile BYTE*)((ptr)+1)<<8)|*(volatile BYTE*)(ptr))
#define ST_WORD(ptr,val)        *(volatile BYTE*)(ptr)=(BYTE)(val); *(volatile BYTE*)((ptr)+1)=(BYTE)((WORD)(val)>>8)
#define ST_DWORD(ptr,val)       *(volatile BYTE*)(ptr)=(BYTE)(val); *(volatile BYTE*)((ptr)+1)=(BYTE)((WORD)(val)>>8); *(volatile BYTE*)((ptr)+2)=(BYTE)((DWORD)(val)>>16); *(volatile BYTE*)((ptr)+3)=(BYTE)((DWORD)(val)>>24)
#else
#error Do not forget to set _MCU_ENDIAN properly!
#endif


#define _FATFS
#endif /* _FATFS */