Subversion Repositories svnkaklik

Rev

Rev 1105 | Rev 1111 | Go to most recent revision | Details | Compare with Previous | Last modification | View Log

Rev Author Line No. Line
1091 fluktuacia 1
\chap Trial design
1073 kaklik 2
 
1105 kaklik 3
The whole design of radioastronomy receiver digitalization unit is constructed to be used in a wide range of applications and tasks related to digitalization of signal from radioastronomy receivers. A good illustrating problem for its use is a signal digitalisation from multiple antenna arrays. This design will eventually become a part of MLAB Advanced Radio Astronomy System. 
1083 kaklik 4
 
1073 kaklik 5
\sec Required parameters
6
 
1098 kaklik 7
Wide dynamical range and high IP3 are desired. The receiver must accept wide dynamic signals because a typical radioastronomical signal has a form of a weak signal covered by a strong man-made noise.    
1073 kaklik 8
 
1098 kaklik 9
Summary of main required parameters follows 
10
 
1083 kaklik 11
\begitems
12
  * Dynamical range better than 80 dB
13
  * Phase stability between channels 
14
  * Noise (all types)
15
  * Sampling jitter better than 100 metres
1098 kaklik 16
  * Support for any number of receivers in range 1 to 8
1083 kaklik 17
\enditems
18
 
1098 kaklik 19
\sec Sampling frequency
20
 
21
Sampling frequency is limited by the technical constrains in the trial design. This parameter is especially limited by the sampling frequencies of analog-to-digital conversion chips available on the market and interface bandwidth. Combination of the required parameters -- dynamic range requiring at least 16bit and a minimum sampling frequency of 1 MSPS leads to need of high end ADC chips which does not support such low sampling frequencies at all. Their minimum sampling frequency is 5 MSPS.
1083 kaklik 22
 
1102 kaklik 23
We calculate minimum data bandwidth data rate for eight receivers, 2 bytes per sample and 5MSPS as $8 * 2 * 5e6 = 80$ MB/s. Such data rate is at the limit of real writing speed o classical HDD and it is almost double of real bandwidth of USB 2.0 interface. 
1083 kaklik 24
 
1073 kaklik 25
 
1075 kaklik 26
\sec System scalability
1073 kaklik 27
 
1098 kaklik 28
For analogue channels scalability, special parameters of ADC modules are required. Ideally, there should be a separate output for each analogue channel in ADC module. ADC module must also have separate outputs for frames and data output clocks. These parameters allow for conduction at relatively low digital data rates. As a result, the digital signal can be conducted even through long wires. 
1073 kaklik 29
 
1093 fluktuacia 30
Clock signal will be handled distinctively in our scalable design. Selected ADC chip are guaranteed to have defined clock skew between sampling and data output clock. This allows taking data and frame clocks from the first ADC module only. The rest of the data and frame clocks from other ADC modules can be measured for diagnostic purposes (failure detection, jitter measurement etc.).
1075 kaklik 31
 
1093 fluktuacia 32
This system concept allows for scalability, that is technically limited by a number of differential signals on host side and its computational power.  There is another advantage of scalable data acquisition system -- an economic one. Observatories or end users can make a choice of how much money are they willing to spent on radioastronomy receiver system. This freedom of choice is especially useful for science sites without previous experience in radioastronomy observations.     
1075 kaklik 33
 
1105 kaklik 34
\secc Differential signaling 
1075 kaklik 35
 
1093 fluktuacia 36
The concept of scalable design requires relatively long circuit traces between ADC and digital unit which captures the data and performs the computations. The long distance between the digital processing unit and the analog-to-digital conversion unit has an advantage in noise retention typically produced by digital circuits. Those digital circuits, such as FPGA or other flip-flops block and circuit traces, usually work at high frequencies and emit wide-band noise with relatively low power. In such cases any increase in a distance between the noise source and analog signal source increase S/N significantly. However, at the same time a long distance brings problems with the digital signal transmission between ADC and computational unit. This obstacle should be resolved more easily in free-space than on board routing. The high-quality differential signalling shielded cables should be used. This technology has two advantages over PCB signal routing. First, it can use twisted pair of wires for leak inductance suppression in signal path and second, the twisted pair may additionally be shielded by uninterrupted metal foil.              
1075 kaklik 37
 
1076 kaklik 38
\secc Phase matching
39
 
1093 fluktuacia 40
For multiple antenna radioastronomy projects, system phase stability is a mandatory condition. It allows precise high resolution imaging of objects. 
1076 kaklik 41
 
1105 kaklik 42
High phase stability in our scalable design is achieved through centralized frequency generation  and distribution with multi-output LVPECL hubs, that have equiphased outputs for multiple devices. 
1076 kaklik 43
 
1093 fluktuacia 44
This design ensures that all devices have access to the defined phase and known frequency.     
1076 kaklik 45
 
46
 
1073 kaklik 47
\sec System description
48
 
1075 kaklik 49
In this section testing system will be described.
1073 kaklik 50
 
1075 kaklik 51
\secc Frequency synthesis       
52
 
1105 kaklik 53
We have used a centralized topology as a basis for frequency synthesis. One precise high-frequency and low-jitter digital oscillator has been used, while other working frequencies have been derived from it by the division of its signal. This central oscillator has a software defined GPS disciplined control loop for frequency stabilization.\fnote{\url{http://wiki.mlab.cz/doku.php?id=en:gpsdo} SDGPSDO design has been developed in parallel to this diploma thesis as a related project, but it is not explicitly required by the diploma thesis.}
1093 fluktuacia 54
We have used methods of frequency monitoring compensation in order to meet modern requirements on radioastronomy equipment which needs precise frequency and phase stability over a wide scale for effective radioastronomy imaging. 
1083 kaklik 55
 
1105 kaklik 56
Every ADC module will be directly connected to CLKHUB02A module which takes sampling clock signal delivered by FPGA from main local oscillator.  This signal should use high quality differential signaling cable -- we should use SATA cable for this purpose. 
1075 kaklik 57
 
1098 kaklik 58
GPSDO design included in data acquisition system has special feature -- generates time marks for precise time-stamping of received signal. Timestamps are created by disabling of local oscillator for 100 us as result rectangle click in input signal is created which appears as horizontal line in spectrogram.   
59
Timestamps should be seen in image \ref[meteor-reflection] (above and below meteor reflection).
60
 
61
Time-marking should be improved in future by digitalisation GPS signal directly with dedicated ADC channel.  Datafile then consists samples from channels of radio-astronomy receivers along with GPS signal containing precise time information. 
62
 
1086 kaklik 63
\secc Signal cable connectors 
1073 kaklik 64
 
1093 fluktuacia 65
Several widely used and commercially easily accessible differential connectors were considered to be use in our design. 
1073 kaklik 66
 
67
\begitems
1077 kaklik 68
* HDMI % [[http://en.wikipedia.org/wiki/Hdmi|HDMI]]</del>
69
* SATA  		%{http://en.wikipedia.org/wiki/Serial_attached_SCSI#Connectors|SAS]]/[[http://en.wikipedia.org/wiki/Serial_ATA|SATA]]
70
* DisplayPort 		%[[http://en.wikipedia.org/wiki/Display_port|DisplayPort]]</del>
71
* SAS/miniSAS
1073 kaklik 72
\enditems
73
 
1093 fluktuacia 74
At the end, MiniSAS connector was chosen as the best option to be used in connecting together multiple ADC modules. It is compatible with existing SATA cabling systems and aggregates multiple SATA cables to a single connector. It can be seen on the following picture \ref[img-miniSAS-cable]. A transition between SATA and miniSAS is achieved by SAS to SATA adapter cable which is commonly used in servers to connect SAS controller to multiple SATA hard disc in RAID systems and thus is commercially easily available. 
75
The main drawback of miniSAS PCB connectors lies in the fact, that they are manufactured in SMT versions only. The outer metal housing of connector is designed to be mounted using a standard through-hole mounting scheme, a design that unfortunately decreases the durability of the connector. 
1073 kaklik 76
 
1085 kaklik 77
 
78
\midinsert
1086 kaklik 79
\clabel[img-miniSAS-cable]{Used miniSAS cable}
1085 kaklik 80
\picw=10cm \cinspic ./img/miniSAS_SATA_cable.jpg
81
\caption/f A type of miniSAS cable similar to used.
82
\endinsert
83
 
1086 kaklik 84
\secc Signal integrity requirements
1105 kaklik 85
\label[diff-signaling]
1085 kaklik 86
 
1105 kaklik 87
We use ADC modules that have DATA clock frequency eight times higher than sampling frequency in single line output mode, implying a 40 MHz output bit rate. This imply $ 1/4*10^7 = 25$ ns time length of data bit, which is equivalent to 7.5m light path in free space. If we use copper PCB with FR4 substrate layer or coaxial/twinax cable, we could obtain velocity factor of 0.66 at worst condition. Then the light path for the same bit rate will be 4.95 m. Although we do not have any cables in system with comparable lengths, worst data bit skew described by data sheets of used components is $0.3*sample time$ time which is 1.485 m. Therefore length matching is not critical in our design. 
1086 kaklik 88
 
89
 
1093 fluktuacia 90
\secc ADC modules design
1073 kaklik 91
 
1083 kaklik 92
 
93
\secc ADC selection
94
 
1105 kaklik 95
There exist several ADC signaling formats currently used in communication with FPGA. 
1083 kaklik 96
 
97
\begitems
98
  * DDR LVDS
99
  * JEDEC 204B
100
  * JESD204A
101
  * Paralel LVDS
102
  * Serdes
103
  * serial LVDS
104
\enditems
105
 
1093 fluktuacia 106
Because it uses the smallest number of differential pairs, the choice fell on the serial LVDS format. Small number of differential pairs is an important parameter determining the construction complexity and reliability. \url{http://www.ti.com/lit/pdf/snaa110}
1083 kaklik 107
 
1093 fluktuacia 108
An ultrasound AFE chip seems to be ideal for this purpose -- the chip has integrated both front-end amplifiers and filters. It has a drawback though - it is incapable of handling differential input signal and has a relatively low dynamic range (as it consists only of 12bit ADC). Because this IO has many ADC channels the scaling is possible only by a factor of 4 receivers (making 8 analogue channels).
1083 kaklik 109
 
1105 kaklik 110
If we require a separate output for every analogue channel and a 16bit depth we find that there are only a few 2-Channel simultaneous sampling ADCs currently existing which meet these requirements.  We have summarized the ADCs in the following table \ref[ADC-type] 
1083 kaklik 111
 
1086 kaklik 112
\midinsert \clabel[ADC-types]{Available ADC types}
113
\ctable{lrrrrrcc}{
114
\hfil ADC Type & LTC2271 & LTC2190 & LTC2191 & LTC2192 & LTC2193 & LTC2194 & LTC2195 \cr
115
SNR [dB] & 84.1 & 77 & 77 & 77 & 76.8 & 76.8 & 76.8 \cr
116
SFDR [dB] & 99 & 90 & 90 & 90 & 90 & 90 & 90 \cr
117
S/H Bandwidth [MHz] & 200 & \multispan6 550 \cr
118
Sampling rate [MSPS] & 20 & 25 & 40 & 65 & 80 &  105 & 125 \cr
119
Configuration & \multispan7 SPI \cr
120
Package & \multispan7 52-Lead (7mm $×$ 8mm) QFN \cr
121
}
1093 fluktuacia 122
\caption/t The summary of available ADC types and theirs characteristics. 
1086 kaklik 123
\endinsert
1083 kaklik 124
 
1093 fluktuacia 125
All parts in this category are compatible with one board layout. Main differences lay in the sampling frequency and signal to noise ratio, with the slowest having a maximum sampling frequency of 20 MHz. However all of them have a minimal sampling frequency of 5 MSPS and all are configurable over a serial interface (SPI). SPI seems to be a standard interface used in high-end ADC chips made by the largest manufacturers (Analog Devices, Linear technology, Texas instruments, Maxim integrated..). 
1083 kaklik 126
 
1105 kaklik 127
 
128
 
129
The ADC modules have a standard MLAB construction scheme with four mounting holes in corners aligned in defined raster. 
130
 
131
Data serial data outputs of ADC modules should be connected directly to FPGAs for the basic primary signal processing. The ADC chip used in the modules has a selectable bit width of data output bus and thus the output SATA connectors have signals arranged to contain a single bit from every ADC channel.  This creates a signal concept enabling a selection of a proper bus bit-width according to the sampling rate (higher bus bit-width downgrades signalling speed and vice versa.)
132
 
133
In order to connect the above mentioned signalling layout, miniSAS to multiple SATA cable should be used.  
134
 
135
A KiCAD design suite had been chosen for PCB layout. However, the version is, despite having integrated CERN Push \& Shove routing capability, slightly unstable as it sometimes crushes due to an exception during routing. On the basis of these stability issues, the design had to be saved quite often. On the other hand, compared to commercially available solutions, such as MentorGraphics PADS or Cadence Orcad,  the Open-source KiCAD provides an acceptable option and it easily surpasses a widely used Eagle software.
136
 
137
As a part of work on the thesis, new PCB footprints for FMC, SATA a and miniSAS connectors have been designed and were committed to KiCAD github library repository. They are now publicly available on the official KiCAD repository at GitHub.  
138
 
139
 
140
 
141
ADCdual01A module has several digital data output formats
142
 
143
\begitems
144
    * 1-lane mode
145
\enditems
146
 
147
All of these modes are supported by module design. For discused data acquisition system the 1-lane mode was selected. 1-lane mode allows minimal number of differential pairs between ADCdual01A and FPGA. Digital signaling scheme used in 1-lane mode is shown in image \ref[1-line-out]. 
148
 
149
\midinsert
150
\clabel[1-line-out]{Single line ADC output signals}
151
\picw=15cm \cinspic ./img/ADC_single_line_output.png
152
\caption/f Digital signaling shema for  1-line  ADC digital output mode.
153
\endinsert
154
 
155
ADCdual01A parameters can be set either by jumper setup (refered as parallel programming  in device's data sheet) or by SPI interface. SPI interface has been selected for our system, because parallel programming lacks of options (test pattern output setup for example). 
156
 
157
Complete schematic diagram of ADCdual01A module board is included in the appendix. 
158
 
159
 
1073 kaklik 160
\secc ADC modules interface
161
 
1096 kaklik 162
Both of the ADCdual01A modules were connected to FPGA ML605 board trough FMC2DIFF01A adapter board. The design of this adapter module expects the presence of FMC LPC connector and the board is, at the same time, not compatible with MLAB. It is, on the other hand, designed to meet the VITA 57 standard specifications for boards which support region 1 and region 3. VITA 57 regions are explained in the picture \ref[VITA57-regions].
1105 kaklik 163
This industry standard guarantees the compatibility with other FPGA boards that have FMC LPC connectors for Mezzanine Card. Schematic diagram of designed adapter board is included in the appendix. 
1073 kaklik 164
 
1094 fluktuacia 165
The primary purpose of the PCB is to enable the connection of ADC modules located outside the PC case. (In PC box analog circuits cannot be realised without the use of massive RFI mitigation techniques). 
166
Differential signalling connectors should be used for conducting digital signal over relatively long cables. The signal integrity sensitive links (clocks) are equipped with output driver and translator to LVPECL logic for better signal transmission quality.  
1083 kaklik 167
 
1073 kaklik 168
\midinsert
169
\picw=10cm \cinspic ./img/ML605-board.jpg
1094 fluktuacia 170
\caption/f FPGA ML605 development board.
1073 kaklik 171
\endinsert
172
 
1096 kaklik 173
\midinsert
174
\clabel[VITA57-regions]{VITA57 board geometry}
175
\picw=10cm \cinspic ./img/VITA57_regions.png
176
\caption/f Definition of VITA57 regions.
177
\endinsert
178
 
1094 fluktuacia 179
Several SATA connectors and two miniSAS connectors are populated on this board.  This set of connectors allows a connection of any number of ADC modules within the range of 1 to 8. ADC data outputs should be connected to the miniSAS connectors, while other supporting signals should be routed directly to SATA connectors on adapter. 
1076 kaklik 180
 
1105 kaklik 181
Lengths of differential pairs routed on PCB of module are not matched between pairs. Length variation of differential pairs is not critical in our design according to facts discussed in paragraph \ref[diff-signaling]. Nevertheless signals within differential pairs itself are matched for length. Internal signal traces length mating of differential pairs is mandatory in order to avoid dynamic logic hazard conditions on digital signals. Thus clocks signals are routed most precisely on all designed boards.
1104 kaklik 182
 
183
 
1094 fluktuacia 184
Signal configuration used in our trial design is described in the following tables. 
1076 kaklik 185
 
1073 kaklik 186
\secc Output data format
187
 
188
\midinsert
1086 kaklik 189
\ctable {clllllllll}{
1073 kaklik 190
\hfil
191
 & \multispan9 \hfil 160bit packet \hfil \crl \tskip4pt
192
Data name &  FRAME  & \multispan2 \hfil ADC1 CH1 \hfil & \multispan2 \hfil ADC1 CH2 \hfil & \multispan2  \hfil ADC2 CH1 \hfil & \multispan2 \hfil ADC2 CH2 \hfil  \cr
193
Data type & uint32 & int16 & int16 & int16 & int16 & int16 & int16 & int16 & int16 \cr
194
Content & saw signal & $t1$ &  $t_{1+1}$ &  $t1$ &  $t_{1+1}$ &  $t1$ &  $t_{1+1}$ &  $t1$ &  $t_{1+1}$ \cr
195
}
196
\caption/t System device "/dev/xillybus_data2_r" data format
197
\endinsert
198
 
199
\sec Achieved parameters
200
 
201
\secc Data reading and recording 
202
 
1094 fluktuacia 203
We use Gnuradio software to read the data stream from the ADC drive. Gnuradio suite consist of gnuradio-companion which is a graphical tool for creating signal-flow graphs and generating flow-graph source code. This tool was used to create a basic RAW data grabber to record and interactively view the data stream output from ADC modules. 
1073 kaklik 204
 
205
\midinsert
206
\picw=15cm \cinspic ./img/screenshots/Grabber.grc.png
1094 fluktuacia 207
\caption/f An ADC recorder flow graph created in gnuradio-companion.
1073 kaklik 208
\endinsert
209
 
210
\midinsert
211
\picw=15cm \cinspic ./img/screenshots/Grabber_running.png
1094 fluktuacia 212
\caption/f User interface window of a running ADC grabber.
1073 kaklik 213
\endinsert
214
 
1094 fluktuacia 215
Interactive grabber viewer user interface shows live oscilloscope-like time-value display for all data channels and live time-frequency scrolling display (a waterfall view) for displaying the frequency components of the grabbed signal. 
1073 kaklik 216
 
1078 kaklik 217
\secc ADC module parameters
1073 kaklik 218
 
1105 kaklik 219
Two pieces of ADC modules were completed and tested. The first piece, labeled ADC1, has LTC2190
220
ADC chip populated with LT6600-5 front-end operational amplifier. It also has a 1kOhm resistors populated on inputs which gives it an ability of an internal attenuation of input signal. The value of this attenuation $A$ is described by the following formula \ref[ADC1-gain]
1078 kaklik 221
 
1105 kaklik 222
\label[ADC1-gain]
1103 kaklik 223
$$
1105 kaklik 224
A = {806 \times R_1 \over R_1 + R_2}
1103 kaklik 225
$$
226
 
227
Where is 
228
\begitems
1105 kaklik 229
  * $A$ -  Gain of input amplifier.
1103 kaklik 230
  * $R_1$ - Output impedance of signal source (usually 50 Ohm).
1105 kaklik 231
  * $R_2$ - Value of serial resistors at operational amplifier inputs.
1103 kaklik 232
\enditems
233
 
1105 kaklik 234
We have $R_2 = 1000 \Omega$ and $R_1 = 50 \Omega$ which imply $A = 0.815$. That value of A is confirmed by measurement. 
235
In our measurement setup we have H1012 Ethernet transformer connected at inputs of ADC. Transformer has 10\% tolerance in impedance and amplification. We measured ADC saturation voltage 705.7 mV (generator output) in this setup due to impedance mismatch and uncalibrated transformer gain. 
1103 kaklik 236
 
1105 kaklik 237
 
1080 kaklik 238
\midinsert
1105 kaklik 239
\clabel[ADC1-FFT]{ADC1 sine test FFT}
240
\picw=15cm \cinspic ./img/screenshots/ADC1_CH2_FFT.png
241
\caption/f Sine signal sampled by ADC1 module with LTC2190 and LT6600-5 devices.
1080 kaklik 242
\endinsert
243
 
1103 kaklik 244
 
1105 kaklik 245
For ADC2 we must use formula with different constant \ref[ADC1-gain]. ADC2 module has LT6600-2.5 populated and gain is $A = 2.457$ with same $R_2$ resistors. We measured saturation voltage of 380 mV (generator output) at channel 1 on this ADC. It is well in parameter tolerances  of used setup.   
1078 kaklik 246
 
1105 kaklik 247
\label[ADC2-gain]
1098 kaklik 248
$$
1105 kaklik 249
A = {1580 \times R_1 \over R_1 + R_2}
1098 kaklik 250
$$
1073 kaklik 251
 
1098 kaklik 252
Where is 
253
\begitems
1105 kaklik 254
  * $A$ -  Gain of input amplifier.
1103 kaklik 255
  * $R_1$ - Output impedance of signal source (usually 50 Ohm).
1105 kaklik 256
  * $R_2$ - Value of serial resistors at operational amplifier inputs.
1098 kaklik 257
\enditems
258
 
1105 kaklik 259
\midinsert
260
\clabel[ADC2-FFT]{ADC2 sine test FFT}
261
\picw=15cm \cinspic ./img/screenshots/ADC2_CH1_FFT.png
262
\caption/f Sine signal sampled by ADC2 module with LTC2271 and LT6600-2.5 devices.
263
\endinsert
1098 kaklik 264
 
1105 kaklik 265
Computed FFT spectra for measured signal are shown in images \ref[ADC2-FFT] and \ref[ADC1-FFT].  Both images confirms that ADCdual01A modules have input dynamical range 80 dB at least. 
1098 kaklik 266
 
267
\chap Example of usage
268
 
1105 kaklik 269
For additional validation of system design a receiver setup was constructed. 
1073 kaklik 270
 
1098 kaklik 271
\sec Basic interferometer station
1073 kaklik 272
 
1105 kaklik 273
Interferometry station was selected as most basic setup. We connected the new data acquisition system to two SDRX01B receivers. Block schematic of used setup is shown in image \ref[block-schematic]. Two ground-plane antennas were used and mounted outside of balcony at CTU building at location 50°4'36.102"N, 14°25'4.170"E. Antennas were equipped  by LNA01A amplifiers. Coaxial cable length are matched for 5 meters. And antennas were isolated by common mode ferrite bead mounted on cable for minimize signal coupling between antennas. Evaluation system consists SDGPSDO local oscillator subsystem used for tunning local oscillator frequency. 
1098 kaklik 274
 
275
\midinsert
1105 kaklik 276
\clabel[block-schematic]{Receiver block schematic}
277
\picw=10cm \cinspic ./img/Coherent_UHF_SDR_receiver.png
278
\caption/f Complete receiver block schematic of dual antenna interferometric station.
279
\endinsert
280
 
281
 
282
 
283
\midinsert
1098 kaklik 284
\clabel[meteor-reflection]{Meteor reflection}
285
\picw=10cm \cinspic ./img/screenshots/observed_meteor.png
286
\caption/f Meteor reflection received by evaluation setup.
287
\endinsert
288
 
289
\midinsert
290
\clabel[phase-phase-difference]{Phase difference}
291
\picw=10cm \cinspic ./img/screenshots/phase_difference.png
292
\caption/f Demonstration of phase difference between antennas.
293
\endinsert
294
 
295
 
296
 
1073 kaklik 297
%\sec Simple passive Doppler radar
298
 
1105 kaklik 299
%\sec Simple polarimeter station
300
 
1075 kaklik 301
\chap Proposed final system
1073 kaklik 302
 
1105 kaklik 303
Construction of a final system which is supposed to be employed for real radioastronomy observations will be described. This chapter is mainly a theoretical analysis of data handling systems. Realization of these ideas might be possible as a part of our future development after we fully evaluate and test the current trial design. 
1073 kaklik 304
 
1107 kaklik 305
The system requires proper handling of huge amounts of data and either huge and fast storage capacity is needed for store captured signal data, or enormous computational power is required for online data processing and filtering. Several hardware approach currently exist and are in use for data processing problem handling. Either powerful multi gigahertz CPUs, GPUs, FPGAs, or specially  constructed ASICs are used for this task.
306
 
1075 kaklik 307
\sec Custom design of FPGA board
1073 kaklik 308
 
1094 fluktuacia 309
In the beginning of the project, a custom design of FPGA interface board had been considered. This FPGA board should include PCI express interface and should sell at lower price than trial design. It should be compatible with MLAB which is further backward compatible with the existing or improved design of ADC modules. For a connection of this board to another adapter board with PCIe we expect a use of a host interface. 
310
Thunderbolt technology standard was expected to be used in this PC to PCIe -> FPGA module. Thunderbolt chips are currently available on the market for reasonable prices. However, a problem lies in the accessibility to their specifications, as they are only available for licensed users and Intel has a mass market oriented licensing policy, that makes this technology inaccessible for low quantity production. As a consequence, an external PCI Express cabling and expansion slots should be considered as a better solution. 
1085 kaklik 311
 
1094 fluktuacia 312
However, these systems and cables are still very expensive. Take (http://www.opalkelly.com/products/xem6110/) as an example, with its price tag reaching 995 USD at time of writing of thesis.
313
Therefore, a better solution probably needs to be found.
1085 kaklik 314
 
1075 kaklik 315
\sec Parralella board computer
316
 
1092 kaklik 317
%Parallella is gon
1075 kaklik 318
 
319
\sec GPU based computational system 
320
 
1094 fluktuacia 321
A new GPU development board NVIDIA K1, shown in the following picture \ref[img-NVIDIA-K1], has recently been released. These boards are intended to be used in fields including computer vision, robotics, medicine, security or automotive industry. They have ideal parameters for signal processing for a relatively low price of 192 USD.  Unfortunately, they are currently only in pre-order release stage (in April 2014). 
1075 kaklik 322
 
1086 kaklik 323
\midinsert
324
\clabel[img-NVIDIA-K1]{NVIDIA Jetson TK1 Development Kit}
325
\picw=15cm \cinspic ./img/Jetson_TK1_575px.jpg
326
\caption/f The NVIDIA Jetson TK1 Development Kit \url{https://developer.nvidia.com/jetson-tk1}.
327
\endinsert
328