Subversion Repositories svnkaklik

Compare Revisions

No changes between revisions

Ignore whitespace Rev 768 → Rev 769

/dokumenty/skolni/ZPOP/detektory/ITP.png
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/dokumenty/skolni/ZPOP/detektory/ITP.txt
0,0 → 1,9
Světelný příkon[mW] Ur[V] Ice [mA]
2.94 2.44 24.3
1.42 1.18 11.8
0.56 0.43 4.3
0.26 0.18 1.8
0.12 0.08 0.8
0.048 0.03 0.3
0.022 0.01 0.1
 
/dokumenty/skolni/ZPOP/detektory/PIN_photovoltanic.png
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/dokumenty/skolni/ZPOP/detektory/PIN_photovoltanic.txt
0,0 → 1,18
U[V] I[mA] P[mW]
0.00 51.4 0.00
0.56 7.18 4.00
0.56 3.8 2.14
0.57 2.1 1.19
0.45 34.6 15.67
0.50 24.53 12.36
0.53 16.82 8.91
0.54 11.52 6.27
0.34 46.1 15.86
0.32 47.8 15.06
0.37 43.7 16.34
0.42 39.45 16.37
0.44 36.81 16.05
0.41 40.3 16.40
0.40 41.2 16.40
0.58 0 0
 
/dokumenty/skolni/ZPOP/detektory/PINplot.gp
0,0 → 1,23
set terminal png
 
set key above
 
set output "VA_PIN.png"
#set multiplot
#set size 0.5,1
set origin 0.0,0.0
#set xrange [-10:0]
set lmargin 10
set rmargin 0
plot "VA_PIN.txt" using 1:2 with lines smooth csplines title "2,94 mW", "" using 1:3 with lines smooth csplines title "0,26 mW"
 
set origin 0.5,0.0
set lmargin 0
set rmargin 2
set nolog x
set xrange [0:1.6]
set xtic 0,10
set mxtic 5
#plot "VA_PIN.txt" using 1:2 with lines smooth csplines exes x2y2
set nomultiplot
 
/dokumenty/skolni/ZPOP/detektory/RP.png
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/dokumenty/skolni/ZPOP/detektory/RP.txt
0,0 → 1,8
2.94 9.191 9.18 180.4428245022
1.42 8.923 8.94 247.4335985655
0.56 8.498 8.4 362.3323134855
0.26 8.066 7.94 491.5323580461
0.12 7.48 7.191 690.6417112299
0.048 6.719 6.024 1001.0492632832
0.022 6.1 4.851 1310.6557377049
 
/dokumenty/skolni/ZPOP/detektory/VA_PIN.png
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/dokumenty/skolni/ZPOP/detektory/VA_PIN.txt
0,0 → 1,24
0 -1.074 -0.093 0
-0.98 -1.076 -0.093 0
-2 -1.07 -0.093 0
-3.03 -1.074 -0.093 0
-4 -1.074 -0.093 0
-5.01 -1.074 -0.093 0
-6 -1.074 -0.093 0
-7.03 -1.074 -0.093 0
-7.98 -1.074 -0.093 0
-9.03 -1.074 -0.093 0
-10 -1.074 -0.093 0
 
0.53 0.002 0.004 0.004
0.6 0.025 0.024 0.024
0.69 0.109 0.107 0.109
0.82 0.353 0.353 0.353
0.9 0.56 0.558 0.558
0.97 0.745 0.753 0.749
1.12 1.187 1.185 1.18
1.2 1.436 1.436 1.436
1.3 1.733 1.733 1.733
1.4 2.04 2.04 2.041
1.5 2.34 2.34 2.342
 
/dokumenty/skolni/ZPOP/detektory/VA_PIN_zaverny.png
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
/dokumenty/skolni/ZPOP/detektory/VA_R.png
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/dokumenty/skolni/ZPOP/detektory/VA_R.txt
0,0 → 1,12
0 0 0 0
1 1.83 1.83 0.479
2 3.68 7.36 0.974
3 5.452 16.356 1.429
4 7.34 29.36 1.922
5 9.157 45.785 2.399
6 11.082 66.492 2.899
7 12.954 90.678 3.37
8 14.83 118.64 3.84
9 16.703 150.327 4.33
10 18.518 185.18 4.779
 
/dokumenty/skolni/ZPOP/detektory/data.ods
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
/dokumenty/skolni/ZPOP/detektory/datektory.pdf
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/dokumenty/skolni/ZPOP/detektory/datektory.tex
0,0 → 1,195
\documentclass[12pt,czech]{article}
 
\usepackage[czech]{babel}
\usepackage[cp1250]{inputenc}
\usepackage{times}
\usepackage{geometry}
\geometry{verbose,a4paper,tmargin=2cm,bmargin=2cm,lmargin=2cm,rmargin=2cm}
 
\usepackage{array}
 
\usepackage{graphicx}
%\usepackage{multirow}
%\usepackage{bigstrut}
%\usepackage{amsbsy}
 
%\pagestyle{plain}
 
%\renewcommand{\tan}{\textrm{tg}}
\newcommand{\tg}{\textrm{tg}}
\newcommand{\cm}{\textrm{cm}}
\newcommand{\m}{\textrm{m}}
\newcommand{\mm}{\textrm{mm}}
\newcommand{\nm}{\textrm{nm}}
 
 
\begin{document}
\noindent \begin{tabular}{|>{\raggedright}b{4cm}|>{\raggedright}b{13cm}|}
\hline
\textbf{Název a \v{c}íslo úlohy}& 2 - Detekce optického záøení
\tabularnewline
\hline
\textbf{Datum m\v{e}\v{r}ení}& 9. 3. 2011
\tabularnewline
\hline
\textbf{M\v{e}\v{r}ení provedli}& TomᚠZikmund, Jakub Kákona
\tabularnewline
\hline
\textbf{Vypracoval}& TomᚠZikmund
\tabularnewline
\hline
\textbf{Datum}&
\tabularnewline
\hline
\textbf{Hodnocení}&
\tabularnewline
\hline
\end{tabular}
 
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
 
\section{Ovìøení vlastností fotoodporu}
Fotoodpor jsme zapojili sériovì s mìøícím odporem s hodnotou $R_z$ = 2050 Ohm. A na oba odpory pøipojili napájecí zdroj $U_0$ = 10 V. Postupnì jsme pak mìnili intenzitu záøení dopadajícího na odpor pomocí šedotónových filtrù a na mìøícím odporu odeèítali napìtí digitálním multimetrem. Výsledný odpor jsme pak vypoèetli z namìøených hodnot, pomocí vztahu. Je vidìt, že odpor fotoodporu s rostoucím osvìtlením klesá a napìtí na mìøícím odporu proto roste.
 
\begin{equation}
R_F = \frac{(U_0 - Uz) R_z}{U_z}
\end{equation}
 
\begin{table}[htbp]
\begin{center}
\begin{tabular}{|c|c|c|c|}
\hline
Svìtelný pøíkon[mW] & Uz [V] Rozsvíceno & Uz [V] Zhasnuto & $R_F$ [Ohm] \\ \hline
2,94 & 9,191 & 9,18 & 180 \\ \hline
1,42 & 8,923 & 8,94 & 247 \\ \hline
0,56 & 8,498 & 8,4 & 362 \\ \hline
0,26 & 8,066 & 7,94 & 491 \\ \hline
0,12 & 7,48 & 7,191 & 690 \\ \hline
0,048 & 6,719 & 6,024 & 1001 \\ \hline
0,022 & 6,1 & 4,851 & 1310 \\ \hline
\end{tabular}
\end{center}
\caption{Namìøené hodnoty napìtí a vypoètené hodnoty fotoodporu}
\label{RP}
\end{table}
 
\begin{figure}[htbp]
\centering
\includegraphics[width=150mm]{RP.png}
\caption{Závislost odporu fotoodporu na výkonu dopadajícího záøení 650nm}
\label{mrizka}
\end{figure}
 
\section{VA charakteristika fotoodporu}
Pøi mìøení voltampérové charakteristiky jsme mìli fotoodpor pøipojený ke zdroji a digitálním multimetrem jsme mìøili jím protékající proud.
 
Namìøená charakteristika pro vìtší dopadající optický výkon se liší od lineární závislosti pravdìpodobnì proto, že odpor fotoodporu byl již dostateènì nízký na to, aby protékající proud mohl zpùsobit zahøátí polovodièe a tím zvýšení protékajícího proudu nad oèekávanou mez.
 
\begin{table}[htbp]
\begin{center}
\begin{tabular}{|c|c|c|}
\hline
\multicolumn{1}{|l|}{} & \multicolumn{ 2}{c|}{I[mA]} \\ \hline
U [V] & 0,26 mW & 0,022 mW \\ \hline
0 & 0 & 0 \\ \hline
1 & 1,83 & 0,479 \\ \hline
2 & 3,68 & 0,974 \\ \hline
3 & 5,452 & 1,429 \\ \hline
4 & 7,34 & 1,922 \\ \hline
5 & 9,157 & 2,399 \\ \hline
6 & 11,082 & 2,899 \\ \hline
7 & 12,954 & 3,37 \\ \hline
8 & 14,83 & 3,84 \\ \hline
9 & 16,703 & 4,33 \\ \hline
10 & 18,518 & 4,779 \\ \hline
\end{tabular}
\end{center}
\caption{Namìøené hodnoty voltampérové charakteristiky fotoodporu}
\label{RP}
\end{table}
 
\begin{figure}[htbp]
\centering
\includegraphics[width=150mm]{VA_R.png}
\caption{VA charakteristika fotoodporu pro dvì hodnoty výkonu dopadajícího záøení}
\label{mrizka}
\end{figure}
 
 
\section{VA charakteristika fotodiody}
 
\section{Spektrální citlivost fotodiody}
 
 
\section{Fotovoltaické zapojení fotodiody}
 
\begin{table}[htbp]
\begin{center}
\begin{tabular}{|c|c|c|}
\hline
U[V] & I[mA] & P[mW] \\ \hline
0,00 & 51,4 & 0,00 \\ \hline
0,56 & 7,18 & 4,00 \\ \hline
0,56 & 3,8 & 2,14 \\ \hline
0,57 & 2,1 & 1,19 \\ \hline
0,45 & 34,6 & 15,67 \\ \hline
0,50 & 24,53 & 12,36 \\ \hline
0,53 & 16,82 & 8,91 \\ \hline
0,54 & 11,52 & 6,27 \\ \hline
0,34 & 46,1 & 15,86 \\ \hline
0,32 & 47,8 & 15,06 \\ \hline
0,37 & 43,7 & 16,34 \\ \hline
0,42 & 39,45 & 16,37 \\ \hline
0,44 & 36,81 & 16,05 \\ \hline
0,41 & 40,3 & 16,40 \\ \hline
0,40 & 41,2 & 16,40 \\ \hline
0,58 & 0 & 0 \\ \hline
\end{tabular}
\end{center}
\caption{PIN dioda ve fotovoltaickem rezimu}
\label{RP}
\end{table}
 
\begin{figure}[htbp]
\centering
\includegraphics[width=150mm]{PIN_photovoltanic.png}
\caption{Charakteristiky PIN diody ve fotovoltaickém režimu}
\label{mrizka}
\end{figure}
 
\section{Proudová charakteristika fototranzistoru}
Pøi mìøení proudové charakteristiky fototranzistoru jsme postupovali obdobnì jako pøi mìøení na fotoodporu. S tím rozdílem, že nyní byl $R_z$ = 100,3 Ohm a napájecí napìtí $U_0$ = 5 V.
 
\begin{table}[htbp]
\begin{center}
\begin{tabular}{|c|c|c|}
\hline
Svìtelný pøíkon[mW] & Ur[V] & Ice [mA] \\ \hline
2,94 & 2,44 & 24,3 \\ \hline
1,42 & 1,18 & 11,8 \\ \hline
0,56 & 0,43 & 4,3 \\ \hline
0,26 & 0,18 & 1,8 \\ \hline
0,12 & 0,08 & 0,8 \\ \hline
0,048 & 0,03 & 0,3 \\ \hline
0,022 & 0,01 & 0,1 \\ \hline
\end{tabular}
\end{center}
\caption{Hodnoty proudu fototranzistorem}
\label{RP}
\end{table}
 
\begin{figure}[htbp]
\centering
\includegraphics[width=150mm]{ITP.png}
\caption{Proud protékající fototranzistorem v závislosti na výkonu dopadajícího záøení}
\label{mrizka}
\end{figure}
 
 
\begin{thebibliography}{99}
 
\bibitem{navod} Kolektiv KFE FJFI ÈVUT: \emph{Úloha è. 2 - Difrakce svìtelného záøení}, [online], [cit. 2. bøezna 2010], http://optics.fjfi.cvut.cz/files/pdf/ZPOP\_02.pdf
 
\end{thebibliography}
 
\end{document}
/dokumenty/skolni/ZPOP/detektory/plot.gp
0,0 → 1,46
set terminal png
 
set grid
 
set logscale xy
set key off
set xlabel "P [mW]"
set ylabel "R [Ohm]"
set output "RP.png"
plot "RP.txt" using 1:4 with points title "0,26 mW"
 
set key above
set xlabel "U [V]"
set ylabel "I [mA]"
set output "VA_R.png"
plot "VA_R.txt" using 1:3 with points title "0,26 mW", "" using 1:4 with points title "0,022 mW"
 
unset logscale xy
set output "VA_PIN_zaverny.png"
set xrange [-10:0]
plot "VA_PIN.txt" using 1:2 with lines smooth csplines title "2,94 mW", "" using 1:3 with lines smooth csplines title "0,26 mW"
set output "VA_PIN_propustny.png"
set xrange [0.3:0.6]
plot "VA_PIN.txt" using 1:2 with lines smooth csplines title "2,94 mW", "" using 1:3 with lines smooth csplines title "0,26 mW"
 
 
set key above
unset logscale xy
set xlabel "U [V]"
set ylabel "I [mA]"
set y2label "P [mW]"
set y2range [0:17]
set y2tics
set xrange [0.3:0.6]
set output "PIN_photovoltanic.png"
plot "PIN_photovoltanic.txt" using 1:2 with points title "Proud" axes x1y1, "" using 1:3 with points title "Výkon" axes x1y2
 
set xrange [0.022:3]
set yrange [0.05:25]
set logscale xy
set key off
set xlabel "P [mW]"
set ylabel "Ice [mA]"
set output "ITP.png"
plot "ITP.txt" using 1:3 with points