| 0,0 → 1,135 |
|---|
| /******************************************************************** |
| FileName: HardwareProfile - Low Pin Count USB Development Kit.h |
| Dependencies: See INCLUDES section |
| Processor: PIC18 or PIC24 USB Microcontrollers |
| Hardware: Low Pin Count USB Development Kit |
| Compiler: Microchip C18 |
| Company: Microchip Technology, Inc. |
| |
| Software License Agreement: |
| |
| The software supplied herewith by Microchip Technology Incorporated |
| (the Company) for its PIC® Microcontroller is intended and |
| supplied to you, the Companys customer, for use solely and |
| exclusively on Microchip PIC Microcontroller products. The |
| software is owned by the Company and/or its supplier, and is |
| protected under applicable copyright laws. All rights are reserved. |
| Any use in violation of the foregoing restrictions may subject the |
| user to criminal sanctions under applicable laws, as well as to |
| civil liability for the breach of the terms and conditions of this |
| license. |
| |
| THIS SOFTWARE IS PROVIDED IN AN AS IS CONDITION. NO WARRANTIES, |
| WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED |
| TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A |
| PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. THE COMPANY SHALL NOT, |
| IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL OR |
| CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER. |
| |
| ******************************************************************** |
| File Description: |
| |
| Change History: |
| Rev Date Description |
| 1.0 11/19/2004 Initial release |
| 2.1 02/26/2007 Updated for simplicity and to use common |
| coding style |
| 2.3 09/15/2008 Broke out each hardware platform into its own |
| "HardwareProfile - xxx.h" file |
| ********************************************************************/ |
| |
| #ifndef HARDWARE_PROFILE_LOW_PIN_COUNT_USB_DEVELOPMENT_KIT_H |
| #define HARDWARE_PROFILE_LOW_PIN_COUNT_USB_DEVELOPMENT_KIT_H |
| |
| /*******************************************************************/ |
| /******** USB stack hardware selection options *********************/ |
| /*******************************************************************/ |
| //This section is the set of definitions required by the MCHPFSUSB |
| // framework. These definitions tell the firmware what mode it is |
| // running in, and where it can find the results to some information |
| // that the stack needs. |
| //These definitions are required by every application developed with |
| // this revision of the MCHPFSUSB framework. Please review each |
| // option carefully and determine which options are desired/required |
| // for your application. |
| |
| //#define USE_SELF_POWER_SENSE_IO |
| #define tris_self_power TRISAbits.TRISA2 // Input |
| #if defined(USE_SELF_POWER_SENSE_IO) |
| #define self_power PORTAbits.RA2 |
| #else |
| #define self_power 1 |
| #endif |
| |
| //#define USE_USB_BUS_SENSE_IO |
| #define tris_usb_bus_sense TRISAbits.TRISA1 // Input |
| #if defined(USE_USB_BUS_SENSE_IO) |
| #define USB_BUS_SENSE PORTAbits.RA1 |
| #else |
| #define USB_BUS_SENSE 1 |
| #endif |
| |
| /*******************************************************************/ |
| /*******************************************************************/ |
| /*******************************************************************/ |
| /******** Application specific definitions *************************/ |
| /*******************************************************************/ |
| /*******************************************************************/ |
| /*******************************************************************/ |
| |
| //Uncomment the following line to make the output HEX of this |
| // project work with the HID Bootloader |
| #define PROGRAMMABLE_WITH_USB_HID_BOOTLOADER |
| |
| /** Board definition ***********************************************/ |
| //These defintions will tell the main() function which board is |
| // currently selected. This will allow the application to add |
| // the correct configuration bits as wells use the correct |
| // initialization functions for the board. These defitions are only |
| // required in the stack provided demos. They are not required in |
| // final application design. |
| |
| #define DEMO_BOARD LOW_PIN_COUNT_USB_DEVELOPMENT_KIT |
| #define LOW_PIN_COUNT_USB_DEVELOPMENT_KIT |
| #define CLOCK_FREQ 48000000 |
| |
| /** LED ************************************************************/ |
| #define mInitAllLEDs() LATC &= 0xF0; TRISC &= 0xF0; |
| |
| #define mLED_1 LATCbits.LATC0 |
| #define mLED_2 LATCbits.LATC1 |
| #define mLED_3 LATCbits.LATC2 |
| #define mLED_4 LATCbits.LATC3 |
| |
| #define mGetLED_1() mLED_1 |
| #define mGetLED_2() mLED_2 |
| #define mGetLED_3() mLED_3 |
| #define mGetLED_4() mLED_4 |
| |
| #define mLED_1_On() mLED_1 = 1; |
| #define mLED_2_On() mLED_2 = 1; |
| #define mLED_3_On() mLED_3 = 1; |
| #define mLED_4_On() mLED_4 = 1; |
| |
| #define mLED_1_Off() mLED_1 = 0; |
| #define mLED_2_Off() mLED_2 = 0; |
| #define mLED_3_Off() mLED_3 = 0; |
| #define mLED_4_Off() mLED_4 = 0; |
| |
| #define mLED_1_Toggle() mLED_1 = !mLED_1; |
| #define mLED_2_Toggle() mLED_2 = !mLED_2; |
| #define mLED_3_Toggle() mLED_3 = !mLED_3; |
| #define mLED_4_Toggle() mLED_4 = !mLED_4; |
| |
| /** SWITCH *********************************************************/ |
| #define mInitSwitch2() //TRISAbits.TRISA3=1 |
| //only one switch available so double duty |
| #define mInitSwitch3() //TRISAbits.TRISA3=1 |
| #define sw2 PORTAbits.RA3 |
| #define sw3 PORTAbits.RA3 |
| #define mInitAllSwitches() mInitSwitch2(); |
| |
| /** POT ************************************************************/ |
| #define mInitPOT() {TRISBbits.TRISB4=1;ADCON0=0x29;ADCON1=0;ADCON2=0x3E;ADCON2bits.ADFM = 1;} |
| |
| #endif //HARDWARE_PROFILE_LOW_PIN_COUNT_USB_DEVELOPMENT_KIT_H |