1,19 → 1,109 |
#include <16F887.h> |
#device adc=8 |
#include "main.h" |
|
#FUSES NOWDT //No Watch Dog Timer |
#FUSES INTRC //Internal RC Osc |
#FUSES NOPUT //No Power Up Timer |
#FUSES MCLR //Master Clear pin enabled |
#FUSES NOPROTECT //Code not protected from reading |
#FUSES NOCPD //No EE protection |
#FUSES NOBROWNOUT //No brownout reset |
#FUSES IESO //Internal External Switch Over mode enabled |
#FUSES FCMEN //Fail-safe clock monitor enabled |
#FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O |
#FUSES NODEBUG //No Debug mode for ICD |
#FUSES NOWRT //Program memory not write protected |
#FUSES BORV40 //Brownout reset at 4.0V |
void SHT25_soft_reset() |
{ |
i2c_start(); // Start condition |
i2c_write(0x80); // Device address |
i2c_write(0xFE); // Device command |
i2c_stop(); // Stop condition |
} |
|
#use delay(clock=8000000) |
unsigned int8 SHT25_setup() |
{ |
unsigned int8 reg; |
|
i2c_start(); // Start condition |
i2c_write(0x80); // Device address |
i2c_write(0xE7); // Device command |
// i2c_stop(); // Stop condition |
|
i2c_start(); // Start condition |
i2c_write(0x81); // Device address |
reg=i2c_read(0); // Device command |
i2c_stop(); // Stop condition |
|
return (reg); |
} |
|
float SHT25_get_temp() |
{ |
unsigned int8 MSB, LSB, Check; |
unsigned int16 data; |
|
i2c_start(); |
I2C_Write(0x80); |
I2C_write(0xE3); |
i2c_stop(); |
|
delay_ms(100); |
|
i2c_start(); |
I2C_Write(0x81); |
MSB=i2c_read(1); |
LSB=i2c_read(1); |
Check=i2c_read(0); |
i2c_stop(); |
|
printf("%X %X %X\r\n",MSB, LSB, Check); |
|
LSB = LSB >> 2; // trow out status bits |
|
data = (((unsigned int16) MSB << 8) + (LSB << 4)); |
return(-46.85 + 175.72*((float)data/0xFFFF)); |
} |
|
float SHT25_get_hum() |
{ |
unsigned int8 MSB, LSB, Check; |
unsigned int16 data; |
|
i2c_start(); //RH |
I2C_Write(0x80); |
I2C_write(0xE5); |
// i2c_stop(); |
|
delay_ms(100); |
|
i2c_start(); |
I2C_Write(0x81); |
MSB=i2c_read(1); |
LSB=i2c_read(1); |
Check=i2c_read(0); |
i2c_stop(); |
|
printf("%X %X %X\r\n",MSB, LSB, Check); |
|
LSB = LSB >> 2; // trow out status bits |
|
data = (((unsigned int16) MSB << 8) + (LSB << 4) ); |
return( -6.0 + 125.0*((float)data/0xFFFF)); |
} |
|
|
void main() |
{ |
|
setup_adc_ports(NO_ANALOGS|VSS_VDD); |
setup_adc(ADC_CLOCK_DIV_2); |
setup_spi(SPI_SS_DISABLED); |
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
setup_timer_1(T1_DISABLED); |
setup_timer_2(T2_DISABLED,0,1); |
setup_ccp1(CCP_OFF); |
setup_comparator(NC_NC_NC_NC); |
|
void SHT25_soft_reset(); |
printf("SHT25 humidity and temperature sensor example \r\n",); |
delay_ms (500); |
|
while(TRUE) |
{ |
printf("setup: %X \r\n",SHT25_setup()); |
delay_ms (500); |
printf("Temp: %f \r\n",SHT25_get_temp()); |
delay_ms (500); |
printf("Hum: %f \r\n",SHT25_get_hum()); |
delay_ms (1000); |
} |
} |
|