Subversion Repositories svnkaklik

Compare Revisions

No changes between revisions

Ignore whitespace Rev 567 → Rev 566

/programy/C/DSC/test/test/main.c
File deleted
/programy/C/avr/tests/Blik/avrm8ledtest.c
File deleted
/programy/C/avr/tests/Blik/avrm8ledtest.hex
File deleted
/programy/C/avr/tests/Blik/avrm8ledtest.out
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Deleted: svn:executable
-*
\ No newline at end of property
Deleted: svn:mime-type
-application/octet-stream
\ No newline at end of property
/programy/C/avr/tests/Blik/prg_read_uc
File deleted
Property changes:
Deleted: svn:executable
-*
\ No newline at end of property
/programy/C/avr/tests/Blik/README.txt
File deleted
/programy/C/avr/tests/Blik/avrm8ledtest_pre.hex
File deleted
/programy/C/avr/tests/Blik/Makefile
File deleted
/programy/C/avr/tests/Blik/prg_load_uc
File deleted
Property changes:
Deleted: svn:executable
-*
\ No newline at end of property
/programy/C/avr/tests/Blik/avrm8ledtest.map
File deleted
/programy/C/avr/tests/Blik/prg_fusebit_uc
File deleted
Property changes:
Deleted: svn:executable
-*
\ No newline at end of property
/programy/C/avr/tests/ATmega168/blik.aps
File deleted
/programy/C/avr/tests/ATmega168/default/blik.elf
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Deleted: svn:mime-type
-application/octet-stream
\ No newline at end of property
/programy/C/avr/tests/ATmega168/default/dep/blik.o.d
File deleted
/programy/C/avr/tests/ATmega168/default/blik.map
File deleted
/programy/C/avr/tests/ATmega168/default/Makefile
File deleted
/programy/C/avr/tests/ATmega168/default/blik.o
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Deleted: svn:mime-type
-application/octet-stream
\ No newline at end of property
/programy/C/avr/tests/ATmega168/default/blik.lss
File deleted
/programy/C/avr/tests/ATmega168/default/blik.hex
File deleted
/programy/C/avr/tests/ATmega168/uart/main.c
File deleted
/programy/C/avr/tests/ATmega168/uart/main.aps
File deleted
/programy/C/avr/tests/ATmega168/uart/uart.c
File deleted
/programy/C/avr/tests/ATmega168/uart/main.aws
File deleted
/programy/C/avr/tests/ATmega168/uart/uart.h
File deleted
/programy/C/avr/tests/ATmega168/uart/default/Makefile
File deleted
/programy/C/avr/tests/ATmega168/uart/default/main.elf
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Deleted: svn:mime-type
-application/octet-stream
\ No newline at end of property
/programy/C/avr/tests/ATmega168/blik.aws
File deleted
/programy/C/avr/Blik/avrm8ledtest.hex
0,0 → 1,11
:1000000012C02CC02BC02AC029C028C027C026C0BF
:1000100025C024C023C022C021C020C01FC01EC0D4
:100020001DC01CC01BC011241FBECFE5D4E0DEBF25
:10003000CDBF10E0A0E6B0E0E4E9F0E002C005903A
:100040000D92A036B107D9F710E0A0E6B0E001C0EC
:100050001D92A036B107E1F70ED01BC0D1CF9C0195
:1000600006C080EF90E00197F1F721503040211554
:100070003105B9F70895CFE5D4E0DEBFCDBFA59A2D
:10008000AD9884EF91E0EBDFAD9A84EF91E0E7DF8C
:04009000F7CFFFCFD8
:00000001FF
/programy/C/avr/Blik/avrm8ledtest.map
0,0 → 1,350
Archive member included because of file (symbol)
 
/usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_exit.o)
/usr/lib/gcc/avr/4.2.2/../../../../avr/lib/avr4/crtm8.o (exit)
/usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_copy_data.o)
avrm8ledtest.o (__do_copy_data)
/usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_clear_bss.o)
avrm8ledtest.o (__do_clear_bss)
 
Memory Configuration
 
Name Origin Length Attributes
text 0x00000000 0x00002000 xr
data 0x00800060 0x0000ffa0 rw !x
eeprom 0x00810000 0x00010000 rw !x
fuse 0x00820000 0x00000400 rw !x
lock 0x00830000 0x00000400 rw !x
signature 0x00840000 0x00000400 rw !x
*default* 0x00000000 0xffffffff
 
Linker script and memory map
 
LOAD /usr/lib/gcc/avr/4.2.2/../../../../avr/lib/avr4/crtm8.o
LOAD avrm8ledtest.o
LOAD /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a
LOAD /usr/lib/gcc/avr/4.2.2/../../../../avr/lib/avr4/libc.a
LOAD /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a
 
.hash
*(.hash)
 
.dynsym
*(.dynsym)
 
.dynstr
*(.dynstr)
 
.gnu.version
*(.gnu.version)
 
.gnu.version_d
*(.gnu.version_d)
 
.gnu.version_r
*(.gnu.version_r)
 
.rel.init
*(.rel.init)
 
.rela.init
*(.rela.init)
 
.rel.text
*(.rel.text)
*(.rel.text.*)
*(.rel.gnu.linkonce.t*)
 
.rela.text
*(.rela.text)
*(.rela.text.*)
*(.rela.gnu.linkonce.t*)
 
.rel.fini
*(.rel.fini)
 
.rela.fini
*(.rela.fini)
 
.rel.rodata
*(.rel.rodata)
*(.rel.rodata.*)
*(.rel.gnu.linkonce.r*)
 
.rela.rodata
*(.rela.rodata)
*(.rela.rodata.*)
*(.rela.gnu.linkonce.r*)
 
.rel.data
*(.rel.data)
*(.rel.data.*)
*(.rel.gnu.linkonce.d*)
 
.rela.data
*(.rela.data)
*(.rela.data.*)
*(.rela.gnu.linkonce.d*)
 
.rel.ctors
*(.rel.ctors)
 
.rela.ctors
*(.rela.ctors)
 
.rel.dtors
*(.rel.dtors)
 
.rela.dtors
*(.rela.dtors)
 
.rel.got
*(.rel.got)
 
.rela.got
*(.rela.got)
 
.rel.bss
*(.rel.bss)
 
.rela.bss
*(.rela.bss)
 
.rel.plt
*(.rel.plt)
 
.rela.plt
*(.rela.plt)
 
.text 0x00000000 0x94
*(.vectors)
.vectors 0x00000000 0x26 /usr/lib/gcc/avr/4.2.2/../../../../avr/lib/avr4/crtm8.o
0x00000000 __vectors
0x00000000 __vector_default
*(.vectors)
*(.progmem.gcc*)
*(.progmem*)
0x00000026 . = ALIGN (0x2)
0x00000026 __trampolines_start = .
*(.trampolines)
.trampolines 0x00000026 0x0 linker stubs
*(.trampolines*)
0x00000026 __trampolines_end = .
*(.jumptables)
*(.jumptables*)
*(.lowtext)
*(.lowtext*)
0x00000026 __ctors_start = .
*(.ctors)
0x00000026 __ctors_end = .
0x00000026 __dtors_start = .
*(.dtors)
0x00000026 __dtors_end = .
SORT(*)(.ctors)
SORT(*)(.dtors)
*(.init0)
.init0 0x00000026 0x0 /usr/lib/gcc/avr/4.2.2/../../../../avr/lib/avr4/crtm8.o
0x00000026 __init
*(.init0)
*(.init1)
*(.init1)
*(.init2)
.init2 0x00000026 0xc /usr/lib/gcc/avr/4.2.2/../../../../avr/lib/avr4/crtm8.o
*(.init2)
*(.init3)
*(.init3)
*(.init4)
.init4 0x00000032 0x16 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_copy_data.o)
0x00000032 __do_copy_data
.init4 0x00000048 0x10 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_clear_bss.o)
0x00000048 __do_clear_bss
*(.init4)
*(.init5)
*(.init5)
*(.init6)
*(.init6)
*(.init7)
*(.init7)
*(.init8)
*(.init8)
*(.init9)
.init9 0x00000058 0x4 /usr/lib/gcc/avr/4.2.2/../../../../avr/lib/avr4/crtm8.o
*(.init9)
*(.text)
.text 0x0000005c 0x2 /usr/lib/gcc/avr/4.2.2/../../../../avr/lib/avr4/crtm8.o
0x0000005c __vector_1
0x0000005c __vector_12
0x0000005c __bad_interrupt
0x0000005c __vector_6
0x0000005c __vector_3
0x0000005c __vector_11
0x0000005c __vector_13
0x0000005c __vector_17
0x0000005c __vector_7
0x0000005c __vector_5
0x0000005c __vector_4
0x0000005c __vector_9
0x0000005c __vector_2
0x0000005c __vector_15
0x0000005c __vector_8
0x0000005c __vector_14
0x0000005c __vector_10
0x0000005c __vector_16
0x0000005c __vector_18
.text 0x0000005e 0x34 avrm8ledtest.o
0x00000076 main
0x0000005e delay_ms
.text 0x00000092 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_exit.o)
.text 0x00000092 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_copy_data.o)
.text 0x00000092 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_clear_bss.o)
0x00000092 . = ALIGN (0x2)
*(.text.*)
.text.libgcc 0x00000092 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_exit.o)
.text.libgcc 0x00000092 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_copy_data.o)
.text.libgcc 0x00000092 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_clear_bss.o)
0x00000092 . = ALIGN (0x2)
*(.fini9)
.fini9 0x00000092 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_exit.o)
0x00000092 exit
0x00000092 _exit
*(.fini9)
*(.fini8)
*(.fini8)
*(.fini7)
*(.fini7)
*(.fini6)
*(.fini6)
*(.fini5)
*(.fini5)
*(.fini4)
*(.fini4)
*(.fini3)
*(.fini3)
*(.fini2)
*(.fini2)
*(.fini1)
*(.fini1)
*(.fini0)
.fini0 0x00000092 0x2 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_exit.o)
*(.fini0)
0x00000094 _etext = .
 
.data 0x00800060 0x0 load address 0x00000094
0x00800060 PROVIDE (__data_start, .)
*(.data)
.data 0x00800060 0x0 /usr/lib/gcc/avr/4.2.2/../../../../avr/lib/avr4/crtm8.o
.data 0x00800060 0x0 avrm8ledtest.o
.data 0x00800060 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_exit.o)
.data 0x00800060 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_copy_data.o)
.data 0x00800060 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_clear_bss.o)
*(.data*)
*(.rodata)
*(.rodata*)
*(.gnu.linkonce.d*)
0x00800060 . = ALIGN (0x2)
0x00800060 _edata = .
0x00800060 PROVIDE (__data_end, .)
 
.bss 0x00800060 0x0 load address 0x00000094
0x00800060 PROVIDE (__bss_start, .)
*(.bss)
.bss 0x00800060 0x0 /usr/lib/gcc/avr/4.2.2/../../../../avr/lib/avr4/crtm8.o
.bss 0x00800060 0x0 avrm8ledtest.o
.bss 0x00800060 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_exit.o)
.bss 0x00800060 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_copy_data.o)
.bss 0x00800060 0x0 /usr/lib/gcc/avr/4.2.2/avr4/libgcc.a(_clear_bss.o)
*(.bss*)
*(COMMON)
0x00800060 PROVIDE (__bss_end, .)
0x00000094 __data_load_start = LOADADDR (.data)
0x00000094 __data_load_end = (__data_load_start + SIZEOF (.data))
 
.noinit 0x00800060 0x0
0x00800060 PROVIDE (__noinit_start, .)
*(.noinit*)
0x00800060 PROVIDE (__noinit_end, .)
0x00800060 _end = .
0x00800060 PROVIDE (__heap_start, .)
 
.eeprom 0x00810000 0x0
*(.eeprom*)
0x00810000 __eeprom_end = .
 
.fuse
*(.fuse)
*(.lfuse)
*(.hfuse)
*(.efuse)
 
.lock
*(.lock*)
 
.signature
*(.signature*)
 
.stab 0x00000000 0x744
*(.stab)
.stab 0x00000000 0x378 /usr/lib/gcc/avr/4.2.2/../../../../avr/lib/avr4/crtm8.o
.stab 0x00000378 0x3cc avrm8ledtest.o
0x3d8 (size before relaxing)
 
.stabstr 0x00000000 0x767
*(.stabstr)
.stabstr 0x00000000 0x767 /usr/lib/gcc/avr/4.2.2/../../../../avr/lib/avr4/crtm8.o
 
.stab.excl
*(.stab.excl)
 
.stab.exclstr
*(.stab.exclstr)
 
.stab.index
*(.stab.index)
 
.stab.indexstr
*(.stab.indexstr)
 
.comment
*(.comment)
 
.debug
*(.debug)
 
.line
*(.line)
 
.debug_srcinfo
*(.debug_srcinfo)
 
.debug_sfnames
*(.debug_sfnames)
 
.debug_aranges
*(.debug_aranges)
 
.debug_pubnames
*(.debug_pubnames)
 
.debug_info
*(.debug_info)
*(.gnu.linkonce.wi.*)
 
.debug_abbrev
*(.debug_abbrev)
 
.debug_line
*(.debug_line)
 
.debug_frame
*(.debug_frame)
 
.debug_str
*(.debug_str)
 
.debug_loc
*(.debug_loc)
 
.debug_macinfo
*(.debug_macinfo)
OUTPUT(avrm8ledtest.out elf32-avr)
LOAD linker stubs
/programy/C/avr/Blik/avrm8ledtest.out
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:executable
+*
\ No newline at end of property
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/programy/C/avr/Blik/avrm8ledtest.c
0,0 → 1,76
/*********************************************
* vim: set sw=8 ts=8 si :
* Author: Guido Socher, Copyright: GPL
* This program is to test the led connected to
* PC5.
* See http://linuxfocus.org/English/November2004/
* for details.
* Chip type : ATMEGA8
* Clock frequency : Internal clock 1 Mhz (factory default)
*********************************************/
#include <avr/io.h>
#include <inttypes.h>
#define F_CPU 1000000UL // 1 MHz
#include <avr/delay.h>
 
 
/* compatibilty macros for old style */
#ifndef cbi
#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
#endif
 
#ifndef sbi
#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
#endif
 
 
void delay_ms(unsigned int ms)
/* delay for a minimum of <ms> */
{
// we use a calibrated macro. This is more
// accurate and not so much compiler dependent
// as self made code.
while(ms){
_delay_ms(0.96);
ms--;
}
}
 
 
/* new style */
int main(void)
{
/* INITIALIZE */
/* enable PC5 as output */
DDRC|= (1<<DDC5);
 
/* PC5 is 5 (see file include/avr/iom8.h) and 1<<PC5 is 00100000
* This can also be written as _BV(PC5)*/
while (1) {
/* led on, pin=0 */
PORTC &= ~(1<<PC5);
delay_ms(500);
/* set output to 5V, LED off */
PORTC|= (1<<PC5);
delay_ms(500);
}
return(0);
}
 
 
// // old style now depricated:
// int main(void)
// {
// // enable PC5 as output
// sbi(DDRC,PC5);
// while (1) {
// // led on, pin=0
// cbi(PORTC,PC5);
// delay_ms(500);
// // set output to 5V, LED off
// sbi(PORTC,PC5);
// delay_ms(500);
// }
// return(0);
// }
// // end of old style
/programy/C/avr/Blik/Makefile
0,0 → 1,62
# makefile, written by guido socher
MCU=atmega8
#MCU=at90s4433
CC=avr-gcc
OBJCOPY=avr-objcopy
# optimize for size:
CFLAGS=-g -mmcu=$(MCU) -Wall -Wstrict-prototypes -Os -mcall-prologues
#-------------------
all: avrm8ledtest.hex
#-------------------
help:
@echo "Usage: make all|load|load_pre|rdfuses|wrfuse1mhz|wrfuse4mhz|wrfusecrystal"
@echo "Warning: you will not be able to undo wrfusecrystal unless you connect an"
@echo " external crystal! uC is dead after wrfusecrystal if you do not"
@echo " have an external crystal."
#-------------------
avrm8ledtest.hex : avrm8ledtest.out
$(OBJCOPY) -R .eeprom -O ihex avrm8ledtest.out avrm8ledtest.hex
avrm8ledtest.out : avrm8ledtest.o
$(CC) $(CFLAGS) -o avrm8ledtest.out -Wl,-Map,avrm8ledtest.map avrm8ledtest.o
avrm8ledtest.o : avrm8ledtest.c
$(CC) $(CFLAGS) -Os -c avrm8ledtest.c
#------------------
load: avrm8ledtest.hex
./prg_load_uc avrm8ledtest.hex
# here is a pre-compiled version in case you have trouble with
# your development environment
load_pre: avrm8ledtest_pre.hex
./prg_load_uc avrm8ledtest.hex
#
loaduisp: avrm8ledtest.hex
./prg_load_uc -u avrm8ledtest.hex
# here is a pre-compiled version in case you have trouble with
# your development environment
load_preuisp: avrm8ledtest_pre.hex
./prg_load_uc -u avrm8ledtest.hex
#-------------------
# fuse byte settings:
# Atmel AVR ATmega8
# Fuse Low Byte = 0xe1 (1MHz internal), 0xe3 (4MHz internal), 0xe4 (8MHz internal)
# Fuse High Byte = 0xd9
# Factory default is 0xe1 for low byte and 0xd9 for high byte
# Check this with make rdfuses
rdfuses:
./prg_fusebit_uc -r
# use internal RC oscillator 1 Mhz
wrfuse1mhz:
./prg_fusebit_uc -w 1
# use internal RC oscillator 4 Mhz
wrfuse4mhz:
./prg_fusebit_uc -w 4
# use external 3-8 Mhz crystal
# Warning: you can not reset this to intenal unless you connect a crystal!!
wrfusecrystal:
@echo "Warning: The external crystal setting can not be changed back without a working crystal"
@echo " You have 3 seconds to abort this with crtl-c"
@sleep 3
./prg_fusebit_uc -w 0
#-------------------
clean:
rm -f *.o *.map *.out *t.hex
#-------------------
/programy/C/avr/Blik/README.txt
0,0 → 1,63
AVR GCC development environment test software.
See the following article for details:
http://main.linuxfocus.org/English/November2004/article352.shtml
 
To compile type the command:
make
 
Note: You will get some warnings "#warning "This header file is obsolete."
during compilation with avr-libc-1.4.X. This is because this code will
also work with avr-libc-1.2.X
 
Alternative 1: Programming with uisp (dapa programmer):
-------------------------------------------------------
Make sure that you have loaded the following modules in the kernel (for 2.4.x)
before you use the uisp programmer:
> /sbin/lsmod
Module Size Used by
parport_pc 17808 0
ppdev 5312 0 (unused)
parport 25856 0 [parport_pc ppdev]
 
 
To compile and load use:
make loaduisp
 
Alternative 2: Programming with avrusb500 (high speed usb programmer from tuxgraphics):
---------------------------------------------------------------------------------------
Make sure that you have loaded the following modules in the kernel
before you use the uisp programmer:
> /sbin/lsmod
Module Size Used by
ftdi_sio 20568 0
usbcore 57792 1 [ftdi_sio usbserial]
 
 
To compile and load use:
make load
 
Files:
------
avrm8ledtest.c # the c source code for ATmega8
avrm8ledtest_pre.hex # pre-compiled loadable object in case you have
# trouble to compile the software
Makefile # Makefile
README.txt # this file
circuit.gif # schematic as gif image
 
-------------------------------------------
History:
version 0.1: 2004-10-01, first Version
version 0.2: 2004-12-30, corrected fault in delay_ms function
version 0.3: 2005-10-04, new modular programming with the scripts prg_load_uc
and prg_fusebit_uc for easy transition to the new
avrusb500 programmer
version 0.4: 2006-03-02, compiler independent delay loop. The old delay_ms
would behave totally different with the new gcc-4
version.
version 0.5: 2006-03-10, Fault in delay_ms corrected
-------------------------------------------
Copyright: GPL
Written by guido socher <guido at tuxgraphics.org>
-------------------------------------------
 
/programy/C/avr/Blik/avrm8ledtest_pre.hex
0,0 → 1,11
:1000000012C02BC02AC029C028C027C026C025C0C6
:1000100024C023C022C021C020C01FC01EC01DC0DC
:100020001CC01BC01AC011241FBECFE5D4E0DEBF28
:10003000CDBF10E0A0E6B0E0E6E9F0E002C0059038
:100040000D92A036B107D9F710E0A0E6B0E001C0EC
:100050001D92A036B107E1F710C0D2CFAC0120E06D
:1000600030E0E0EFF0E005C0CF010197F1F72F5F3E
:100070003F4F24173507C1F70895CFE5D4E0DEBF21
:10008000CDBFA59AAD9884EF91E0E8DFAD9A84EFFB
:0600900091E0E4DFF7CF70
:00000001FF
/programy/C/avr/Blik/prg_fusebit_uc
0,0 → 1,97
#!/bin/sh
prg="adude"
#
help()
{
echo "prg_fusebit_uc -- read and write fuse bits of the atmega8"
echo ""
echo "Usage: prg_fusebit_uc [-hu] -r|-w Freq"
echo ""
echo "OPTIONS: -h this help"
echo " -r read fuse bytes"
echo " -u use uisp instead of avrdude"
echo " avrdude can automatically detect dapa or avrusb500."
echo " uisp can only be used with the parallel port dapa."
echo " -w write fuse bytes such that a given Freq is used"
echo " a frequency of 0 means external crystal. Possible"
echo " values are 0,1,2,4,8"
echo ""
echo "EXAMPLE: program the fuses to 4MHz internal"
echo " prg_fusebit_uc -w 4"
echo ""
echo "Warning: you can not undo the setting \"external crystal\" unless"
echo " you have a crystal that works."
echo "This script can be easily adapted to different programmer types"
exit 0
}
while [ -n "$1" ]; do
case $1 in
-h) help;shift 1;;
-u) prg="uisp";shift 1;;
-r) opt_r="1";shift 1;;
-w) opt_w="1";freq="$2";shift 2;;
-*) echo "error: no such option $1. -h for help";exit 1;;
*) break;;
esac
done
 
if [ -z "$opt_r" -a -z "$opt_w" ];then
# one of those options is mandatory
help
fi
 
hf=0xd9
if [ "$opt_w" = "1" ]; then
case $freq in
0) lf=0xee;echo "Make sure you have a crystal otherwise you can not change this!";sleep 2;;
1) lf=0xe1;;
2) lf=0xe2;;
4) lf=0xe3;;
8) lf=0xe4;;
*) echo "error: no such frequency, -h for help";exit 1;;
esac
fi
 
 
if [ "$prg" = "uisp" ]; then
if [ "$opt_r" = "1" ];then
set -x
uisp -dlpt=/dev/parport0 -dprog=dapa --rd_fuses
set +x
echo "Explanation: Fuse Low Byte: 0xe1 (1MHz intern), 0xe3 (4MHz intern), "
echo " 0xe4 (8MHz intern)"
echo " Fuse High Byte should be 0xd9"
exit 0
fi
if [ "$opt_w" = "1" ]; then
set -x
uisp -dlpt=/dev/parport0 -dprog=dapa --wr_fuse_l=$lf
uisp -dlpt=/dev/parport0 -dprog=dapa --wr_fuse_h=$hf
set +x
exit 0
fi
 
fi
if [ "$prg" = "adude" ]; then
if grep "Vendor=0403 ProdID=6001" /proc/bus/usb/devices > /dev/null ; then
prg="avrusb500"
else
prg="dapa"
fi
if [ "$opt_r" = "1" ];then
set -x
avrdude -p m8 -c $prg -v -q
set +x
echo "Explanation: Fuse Low Byte: 0xe1 (1MHz intern), 0xe3 (4MHz intern), "
echo " 0xe4 (8MHz intern)"
echo " Fuse High Byte should be 0xd9"
exit 0
fi
if [ "$opt_w" = "1" ]; then
set -x
avrdude -p m8 -c $prg -u -v -U lfuse:w:$lf:m
avrdude -p m8 -c $prg -u -v -U hfuse:w:$hf:m
set +x
exit 0
fi
fi
Property changes:
Added: svn:executable
+*
\ No newline at end of property
/programy/C/avr/Blik/prg_load_uc
0,0 → 1,38
#!/bin/sh
prg="adude"
if [ "$1" = "-u" ]; then
shift;
prg="uisp"
fi
if [ -z "$1" -o "$1" = "-h" -o "$1" = "--help" ]; then
echo "prg_load_uc -- load a .hex file into a atmega8 microcontroller"
echo ""
echo "Usage: prg_load_uc [-hu] File.hex"
echo ""
echo "OPTIONS: -h this help"
echo " -u use uisp instead of avrdude"
echo " avrdude can automatically detect dapa or avrusb500."
echo " uisp can only be used with the parallel port dapa."
echo ""
echo "This script can be easily adapted to different programmer types"
exit 0
fi
pfile="$1"
 
if [ "$prg" = "uisp" ]; then
set -x
uisp -dlpt=/dev/parport0 --erase -dprog=dapa
uisp -dlpt=/dev/parport0 --upload if="$pfile" -dprog=dapa -v=3 --hash=32 --verify
set +x
fi
if [ "$prg" = "adude" ]; then
if grep "Vendor=0403 ProdID=6001" /proc/bus/usb/devices > /dev/null ; then
set -x
avrdude -p m8 -c avrusb500 -e -U flash:w:"$pfile"
set +x
else
set -x
avrdude -p m8 -c dapa -e -U flash:w:"$pfile"
set +x
fi
fi
Property changes:
Added: svn:executable
+*
\ No newline at end of property
/programy/C/avr/Blik/prg_read_uc
0,0 → 1,38
#!/bin/sh
prg="adude"
if [ "$1" = "-u" ]; then
shift;
prg="uisp"
fi
if [ -z "$1" -o "$1" = "-h" -o "$1" = "--help" ]; then
echo "prg_read_uc -- read the flahs of an atmega8 microcontroller"
echo ""
echo "Usage: prg_load_uc [-hu] File.hex"
echo ""
echo "OPTIONS: -h this help"
echo " -u use uisp instead of avrdude"
echo " avrdude can automatically detect dapa or avrusb500."
echo " uisp can only be used with the parallel port dapa."
echo ""
echo "This script can be easily adapted to different programmer types"
exit 0
fi
pfile="$1"
 
if [ "$prg" = "uisp" ]; then
set -x
#uisp -dlpt=/dev/parport0 --erase -dprog=dapa
#uisp -dlpt=/dev/parport0 --upload if="$pfile" -dprog=dapa -v=3 --hash=32 --verify
set +x
fi
if [ "$prg" = "adude" ]; then
if grep "Vendor=0403 ProdID=6001" /proc/bus/usb/devices > /dev/null ; then
set -x
avrdude -v -v -p m8 -c avrusb500 -U flash:r:"$pfile:i"
set +x
else
set -x
avrdude -p m8 -c dapa -U flash:r:"$pfile:i"
set +x
fi
fi
Property changes:
Added: svn:executable
+*
\ No newline at end of property
/programy/C/PIC_C/test/C16F873/blik/main.c
20,12 → 20,12
{
output_c(ble++);
delay_ms(100);
 
/*
Output_high(PIN_B2);
Delay_ms(100);
Output_low(PIN_B2);
Delay_ms(100);
 
*/
}
 
}
/programy/C/PIC_C/test/C16F876A/blik/blik.PJT
10,7 → 10,7
LinkerScript=
 
[Target Data]
FileList=D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.c
FileList=D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.c
BuildTool=C-COMPILER
OptionString=+FM
AdditionalOptionString=
35,4 → 35,4
2=
[Units]
Count=1
1=D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.c (main)
1=D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.c (main)
/programy/C/PIC_C/test/C16F876A/blik/blik.cof
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
/programy/C/PIC_C/test/C16F876A/blik/blik.lst
1,6 → 1,6
CCS PCM C Compiler, Version 3.245, 27853 29-VI-08 23:25
CCS PCM C Compiler, Version 3.245, 27853 23-II-07 18:50
 
Filename: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.lst
Filename: D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.lst
 
ROM used: 114 words (1%)
Largest free fragment is 2048
/programy/C/PIC_C/test/C16F876A/blik/blik.sta
10,8 → 10,8
 
Lines Stmts % Files
----- ----- --- -----
25 14 100 D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.c
16 0 0 D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.h
25 14 100 D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.c
16 0 0 D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.h
270 0 0 C:\Program Files\PICC\devices\16F876A.h
----- -----
622 28 Total
/programy/C/PIC_C/test/C16F876A/blik/blik.sym
21,12 → 21,12
0017 @cinit
 
Project Files:
D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.c
D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.h
D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.c
D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.h
C:\Program Files\PICC\devices\16F876A.h
 
Units:
D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.c (main)
D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.c (main)
 
Compiler Settings:
Processor: PIC16F876A
36,10 → 36,10
Short,Int,Long: 1,8,16
 
Output Files:
Errors: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.err
INHX8: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.hex
Symbols: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.sym
List: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.lst
Debug/COFF: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.cof
Call Tree: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.tre
Statistics: D:\KAKLIK\projekty\programy\C\PIC_C\test\C16F876A\blik\blik.sta
Errors: D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.err
INHX8: D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.hex
Symbols: D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.sym
List: D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.lst
Debug/COFF: D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.cof
Call Tree: D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.tre
Statistics: D:\KAKLIK\projekty\programy\PIC_C\test\C16F876A\blik\blik.sta