| 0,0 → 1,115 |
|---|
| PRG = eq6 |
| OBJ = eq6.o paddle.o combine.o stepper.o driver.o serial.o \ |
| pguide.o sr.o |
| MCU_TARGET = atmega162 |
| |
| OPTIMIZE = -O2 |
| |
| DEFS = |
| LIBS = |
| |
| # You should not have to change anything below here. |
| |
| CC = avr-gcc |
| |
| # Override is only needed by avr-lib build system. |
| |
| override CFLAGS = -g -Wall $(OPTIMIZE) -mmcu=$(MCU_TARGET) $(DEFS) |
| override LDFLAGS = -Wl,-Map,$(PRG).map |
| |
| OBJCOPY = avr-objcopy |
| OBJDUMP = avr-objdump |
| |
| all: $(PRG).cof lst text eeprom |
| |
| $(PRG).elf: $(OBJ) |
| $(CC) $(CFLAGS) $(LDFLAGS) -o $@ $^ $(LIBS) |
| |
| $(PRG).cof: $(PRG).elf |
| $(OBJCOPY) \ |
| --debugging \ |
| -O coff-ext-avr \ |
| --change-section-address .data-0x800000 \ |
| --change-section-address .bss-0x800000 \ |
| --change-section-address .noinit-0x800000 \ |
| --change-section-address .eeprom-0x810000 \ |
| $(PRG).elf $(PRG).cof |
| |
| |
| release: |
| $(MAKE) clean |
| $(MAKE) DEFS=-DCLK_RATE=8000000 |
| mv eq6.hex eq6_8MHz.sav |
| $(MAKE) clean |
| $(MAKE) DEFS=-DCLK_RATE=16000000 |
| mv eq6.hex eq6_16MHz.sav |
| $(MAKE) clean |
| mv eq6_8MHz.sav eq6_8MHz.hex |
| mv eq6_16MHz.sav eq6_16MHz.hex |
| |
| |
| |
| clean: |
| rm -rf *.o $(PRG).elf *.eps *.png *.pdf *.bak |
| rm -rf *.lst *.map $(EXTRA_CLEAN_FILES) |
| |
| lst: $(PRG).lst |
| |
| %.lst: %.elf |
| $(OBJDUMP) -h -S $< > $@ |
| |
| # Rules for building the .text rom images |
| |
| text: hex bin srec |
| |
| hex: $(PRG).hex |
| bin: $(PRG).bin |
| srec: $(PRG).srec |
| |
| %.hex: %.elf |
| $(OBJCOPY) -j .text -j .data -O ihex $< $@ |
| |
| %.srec: %.elf |
| $(OBJCOPY) -j .text -j .data -O srec $< $@ |
| |
| %.bin: %.elf |
| $(OBJCOPY) -j .text -j .data -O binary $< $@ |
| |
| # Rules for building the .eeprom rom images |
| |
| eeprom: ehex ebin esrec |
| |
| ehex: $(PRG)_eeprom.hex |
| ebin: $(PRG)_eeprom.bin |
| esrec: $(PRG)_eeprom.srec |
| |
| %_eeprom.hex: %.elf |
| $(OBJCOPY) -j .eeprom --change-section-lma .eeprom=0 -O ihex $< $@ |
| |
| %_eeprom.srec: %.elf |
| $(OBJCOPY) -j .eeprom --change-section-lma .eeprom=0 -O srec $< $@ |
| |
| %_eeprom.bin: %.elf |
| $(OBJCOPY) -j .eeprom --change-section-lma .eeprom=0 -O binary $< $@ |
| |
| # Every thing below here is used by avr-libc's build system and can be ignored |
| # by the casual user. |
| |
| FIG2DEV = fig2dev |
| EXTRA_CLEAN_FILES = *.hex *.bin *.srec |
| |
| dox: eps png pdf |
| |
| eps: $(PRG).eps |
| png: $(PRG).png |
| pdf: $(PRG).pdf |
| |
| %.eps: %.fig |
| $(FIG2DEV) -L eps $< $@ |
| |
| %.pdf: %.fig |
| $(FIG2DEV) -L pdf $< $@ |
| |
| %.png: %.fig |
| $(FIG2DEV) -L png $< $@ |
| |