Subversion Repositories svnkaklik

Compare Revisions

No changes between revisions

Ignore whitespace Rev 5 → Rev 6

/programy/PIC_C/motory/DC/regulator_letadlo/main.BAK
0,0 → 1,14
#include "D:\@Kaklik\programy\PIC_C\motory\DC\regulator_letadlo\main.h"
 
 
void main()
{
while (true)
{
 
output_high(pin_A1);
Delay_us(50);
output_low(pin_A1);
Delay_us(500);
}
}
/programy/PIC_C/motory/DC/regulator_letadlo/main.HEX
0,0 → 1,7
:1000000000308A000428000084011F308305831615
:1000100085108312851403308C008C0B0D288316F9
:1000200085108312851031308C008C0B1528000050
:0600300000000728630038
:02400E00F93F78
:00000001FF
;PIC16F84
/programy/PIC_C/motory/DC/regulator_letadlo/main.LST
0,0 → 1,62
CCS PCW C Compiler, Version 3.110, 15448
 
Filename: d:\@kaklik\programy\pic_c\motory\dc\regulator_letadlo\main.LST
 
ROM used: 27 (3%)
Largest free fragment is 997
RAM used: 2 (3%) at main() level
2 (3%) worst case
Stack: 0 locations
 
*
0000: MOVLW 00
0001: MOVWF 0A
0002: GOTO 004
0003: NOP
.................... #include "D:\@Kaklik\programy\PIC_C\motory\DC\regulator_letadlo\main.h"
.................... #include <16F84.h>
.................... //////// Standard Header file for the PIC16F84 device ////////////////
.................... #device PIC16F84
.................... #list
....................
.................... #use delay(clock=4000000)
.................... #fuses XT,NOWDT
....................
....................
....................
....................
.................... void main()
.................... {
0004: CLRF 04
0005: MOVLW 1F
0006: ANDWF 03,F
.................... while (true)
.................... {
....................
.................... output_high(pin_A1);
0007: BSF 03.5
0008: BCF 05.1
0009: BCF 03.5
000A: BSF 05.1
.................... Delay_us(10);
000B: MOVLW 03
000C: MOVWF 0C
000D: DECFSZ 0C,F
000E: GOTO 00D
.................... output_low(pin_A1);
000F: BSF 03.5
0010: BCF 05.1
0011: BCF 03.5
0012: BCF 05.1
.................... Delay_us(150);
0013: MOVLW 31
0014: MOVWF 0C
0015: DECFSZ 0C,F
0016: GOTO 015
0017: NOP
0018: NOP
.................... }
0019: GOTO 007
.................... }
....................
001A: SLEEP
/programy/PIC_C/motory/DC/regulator_letadlo/main.PJT
0,0 → 1,32
[PROJECT]
Target=main.HEX
Development_Mode=
Processor=0x684A
ToolSuite=CCS
 
[Directories]
Include=C:\PROGRAM FILES\PICC\devices\;C:\PROGRAM FILES\PICC\dr
Library=
LinkerScript=
 
[Target Data]
FileList=main.c;
BuildTool=C-COMPILER
OptionString=+FM
AdditionalOptionString=
BuildRequired=1
 
[main.c]
Type=4
Path=
FileList=
BuildTool=
OptionString=
AdditionalOptionString=
 
[mru-list]
1=main.c
 
[Windows]
0=0000 main.c 0 0 796 451 3 0
 
/programy/PIC_C/motory/DC/regulator_letadlo/main.SYM
0,0 → 1,12
00C @SCRATCH
00D @SCRATCH
00D _RETURN_
delay_ms.P1
delay_us.P2
 
0004 main
 
Project Files:
d:\@kaklik\programy\pic_c\motory\dc\regulator_letadlo\main.c
D:\@Kaklik\programy\PIC_C\motory\DC\regulator_letadlo\main.h
C:\PROGRAM FILES\PICC\devices\16F84.h
/programy/PIC_C/motory/DC/regulator_letadlo/main.c
0,0 → 1,14
#include "D:\@Kaklik\programy\PIC_C\motory\DC\regulator_letadlo\main.h"
 
 
void main()
{
while (true)
{
 
output_high(pin_A1);
Delay_us(10);
output_low(pin_A1);
Delay_us(150);
}
}
/programy/PIC_C/motory/DC/regulator_letadlo/main.cod
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/programy/PIC_C/motory/DC/regulator_letadlo/main.err
0,0 → 1,0
No Errors
/programy/PIC_C/motory/DC/regulator_letadlo/main.h
0,0 → 1,4
#include <16F84.h>
#use delay(clock=4000000)
#fuses XT,NOWDT
 
/programy/PIC_C/motory/DC/regulator_letadlo/main.sta
0,0 → 1,27
 
ROM used: 27 (3%)
997 (97%) including unused fragments
 
0 Average locations per line
4 Average locations per statement
 
RAM used: 2 (3%) at main() level
2 (3%) worst case
 
Lines Stmts % Files
----- ----- --- -----
15 6 100 d:\@kaklik\programy\pic_c\motory\dc\regulator_letadlo\main.c
5 0 0 D:\@Kaklik\programy\PIC_C\motory\DC\regulator_letadlo\main.h
111 0 0 C:\PROGRAM FILES\PICC\devices\16F84.h
----- -----
262 12 Total
 
Page ROM % RAM Functions:
---- --- --- --- ----------
0 23 85 0 main
 
Segment Used Free
--------- ---- ----
0000-0003 4 0
0004-03FF 23 997
 
/programy/PIC_C/motory/DC/regulator_letadlo/main.tre
0,0 → 1,3
ÀÄmain
ÀÄmain 0/23 Ram=0
ÀÄ??0??
/programy/PIC_C/motory/DC/regulator_letadlo/prg.bat
0,0 → 1,6
call picpgr stop
call picpgr erase pic16f84
call picpgr program main.hex hex pic16f84
call picpgr run
pause
call picpgr stop
/programy/PIC_C/motory/DC/regulator_letadlo/vssver.scc
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/programy/PIC_C/motory/hodinovy/Run.BAT
0,0 → 1,8
@echo off
:loop
picpgr reset PIC16F84
picpgr run
pause
picpgr stop
pause
goto loop
/programy/PIC_C/motory/hodinovy/main.BAK
0,0 → 1,22
#include "D:\@Kaklik\programy\PIC_C\motory\main.h"
 
 
void main()
{
while (true)
{
 
Delay_ms(15);
output_high(pin_A0);
output_low(pin_A1);
// output_high(pin_A2);
// Delay_ms(10);
// output_low(pin_A2);
Delay_ms(15);
output_low(pin_A0);
output_high(pin_A1);
}
}
/programy/PIC_C/motory/hodinovy/main.HEX
0,0 → 1,10
:1000000000308A00192800000F308400000803190E
:10001000182801308D008C018C0B0C288D0B0B28BF
:100020004A308C008C0B122800000000800B09283D
:10003000003484011F30830519308F00042083169B
:10004000051083120514831685108312851019304C
:100050008F00042083160510831205108316851067
:08006000831285141C286300C3
:02400E00FD3F74
:00000001FF
;PIC16F84
/programy/PIC_C/motory/hodinovy/main.LST
0,0 → 1,95
CCS PCW C Compiler, Version 3.110, 15448
 
Filename: d:\@kaklik\programy\pic_c\motory\main.LST
 
ROM used: 52 (5%)
Largest free fragment is 972
RAM used: 2 (3%) at main() level
3 (4%) worst case
Stack: 1 locations
 
*
0000: MOVLW 00
0001: MOVWF 0A
0002: GOTO 019
0003: NOP
.................... #include "D:\@Kaklik\programy\PIC_C\motory\main.h"
.................... #include <16F84.h>
.................... //////// Standard Header file for the PIC16F84 device ////////////////
.................... #device PIC16F84
.................... #list
....................
.................... #use delay(clock=4000000)
0004: MOVLW 0F
0005: MOVWF 04
0006: MOVF 00,W
0007: BTFSC 03.2
0008: GOTO 018
0009: MOVLW 01
000A: MOVWF 0D
000B: CLRF 0C
000C: DECFSZ 0C,F
000D: GOTO 00C
000E: DECFSZ 0D,F
000F: GOTO 00B
0010: MOVLW 4A
0011: MOVWF 0C
0012: DECFSZ 0C,F
0013: GOTO 012
0014: NOP
0015: NOP
0016: DECFSZ 00,F
0017: GOTO 009
0018: RETLW 00
.................... #fuses XT,WDT
....................
....................
....................
....................
.................... void main()
.................... {
0019: CLRF 04
001A: MOVLW 1F
001B: ANDWF 03,F
.................... while (true)
.................... {
....................
.................... Delay_ms(25);
001C: MOVLW 19
001D: MOVWF 0F
001E: CALL 004
....................
.................... output_high(pin_A0);
001F: BSF 03.5
0020: BCF 05.0
0021: BCF 03.5
0022: BSF 05.0
.................... output_low(pin_A1);
0023: BSF 03.5
0024: BCF 05.1
0025: BCF 03.5
0026: BCF 05.1
....................
.................... // output_high(pin_A2);
.................... // Delay_ms(10);
.................... // output_low(pin_A2);
.................... Delay_ms(25);
0027: MOVLW 19
0028: MOVWF 0F
0029: CALL 004
....................
.................... output_low(pin_A0);
002A: BSF 03.5
002B: BCF 05.0
002C: BCF 03.5
002D: BCF 05.0
.................... output_high(pin_A1);
002E: BSF 03.5
002F: BCF 05.1
0030: BCF 03.5
0031: BSF 05.1
.................... }
0032: GOTO 01C
.................... }
....................
0033: SLEEP
/programy/PIC_C/motory/hodinovy/main.PJT
0,0 → 1,32
[PROJECT]
Target=main.HEX
Development_Mode=
Processor=0x684A
ToolSuite=CCS
 
[Directories]
Include=C:\PROGRAM FILES\PICC\devices\;C:\PROGRAM FILES\PICC\dr
Library=
LinkerScript=
 
[Target Data]
FileList=main.c;
BuildTool=C-COMPILER
OptionString=+FM
AdditionalOptionString=
BuildRequired=1
 
[main.c]
Type=4
Path=
FileList=
BuildTool=
OptionString=
AdditionalOptionString=
 
[mru-list]
1=main.c
 
[Windows]
0=0000 main.c 0 0 796 451 3 0
 
/programy/PIC_C/motory/hodinovy/main.SYM
0,0 → 1,14
00C @SCRATCH
00D @SCRATCH
00D _RETURN_
00F delay_ms.P1
delay_us.P1
 
0004 delay_ms
0019 main
0040 @cinit
 
Project Files:
d:\@kaklik\programy\pic_c\motory\main.c
D:\@Kaklik\programy\PIC_C\motory\main.h
C:\PROGRAM FILES\PICC\devices\16F84.h
/programy/PIC_C/motory/hodinovy/main.c
0,0 → 1,22
#include "D:\@Kaklik\programy\PIC_C\motory\main.h"
 
 
void main()
{
while (true)
{
 
Delay_ms(25);
output_high(pin_A0);
output_low(pin_A1);
// output_high(pin_A2);
// Delay_ms(10);
// output_low(pin_A2);
Delay_ms(25);
output_low(pin_A0);
output_high(pin_A1);
}
}
/programy/PIC_C/motory/hodinovy/main.cod
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/programy/PIC_C/motory/hodinovy/main.err
0,0 → 1,0
No Errors
/programy/PIC_C/motory/hodinovy/main.h
0,0 → 1,4
#include <16F84.h>
#use delay(clock=4000000)
#fuses XT,WDT
 
/programy/PIC_C/motory/hodinovy/main.sta
0,0 → 1,28
 
ROM used: 52 (5%)
972 (95%) including unused fragments
 
0 Average locations per line
6 Average locations per statement
 
RAM used: 2 (3%) at main() level
3 (4%) worst case
 
Lines Stmts % Files
----- ----- --- -----
23 8 100 d:\@kaklik\programy\pic_c\motory\main.c
5 0 0 D:\@Kaklik\programy\PIC_C\motory\main.h
111 0 0 C:\PROGRAM FILES\PICC\devices\16F84.h
----- -----
278 16 Total
 
Page ROM % RAM Functions:
---- --- --- --- ----------
0 21 40 1 delay_ms
0 27 52 0 main
 
Segment Used Free
--------- ---- ----
0000-0003 4 0
0004-03FF 48 972
 
/programy/PIC_C/motory/hodinovy/main.tre
0,0 → 1,5
ÀÄmain
ÀÄmain 0/27 Ram=0
ÃÄ??0??
ÃÄdelay_ms 0/21 Ram=1
ÀÄdelay_ms 0/21 Ram=1
/programy/PIC_C/motory/hodinovy/prg.bat
0,0 → 1,6
call picpgr stop
call picpgr erase pic16f84
call picpgr program main.hex hex pic16f84
call picpgr run
pause
call picpgr stop
/programy/PIC_C/motory/hodinovy/vssver.scc
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/programy/PIC_C/motory/krokac/A.BAT
0,0 → 1,3
call picpgr erase pic16f88
call picpgr program krokac.hex hex pic16f88
call picpgr run
/programy/PIC_C/motory/krokac/KROKAC.C
0,0 → 1,139
#include "C:\MIHO_DAT\KROKAC\krokac.h"
 
 
unsigned int StepState; // Vnitrni promenna kroku
signed int StepDirection; // Smer +1/0/-1
 
byte const StepTab[8]={ // Tabulka pro krokovy motor
0b0001, // 0
0b0101, // 1
0b0100, // 2
0b0110, // 3
0b0010, // 4
0b1010, // 5
0b1000 // 6
0b1001, // 7
};
#INT_TIMER2
void StepNext()
{
unsigned int i;
StepState+=StepDirection; // posun se na dalsi krok
i=StepState&0b111; // vezmi spodni 3 bity stavu
i=StepTab[i]; // prekoduj pomoci tabulky
output_bit(MOTORA,i&0b0001); // aktivuj jednotlive vystupy
output_bit(MOTORB,i&0b0010);
output_bit(MOTORC,i&0b0100);
output_bit(MOTORD,i&0b1000);
}
 
 
void StepSetDirection(signed int Direction)
{
if(Direction> 1) Direction= 1;
if(Direction<-1) Direction=-1;
StepDirection=Direction;
}
 
 
void StepSetTime(unsigned int16 Time)
{
}
 
void Delay(unsigned int16 Time)
{
while(Time>255) {Time-=256;delay_us(256);};
if(Time!=0) delay_us(Time);
}
 
 
void main()
{
unsigned int16 T;
unsigned long int i;
 
// Nastav pracovni frekvenci procesoru
setup_oscillator(OSC_4MHZ);
 
// Vypni motorovy vystup
output_low(MOTORA);
output_low(MOTORB);
output_low(MOTORC);
output_low(MOTORD);
 
// Vstupy s pull-up odporem
port_b_pullups(TRUE);
 
// Inicializace A/D prevodniku
setup_adc_ports(sAN0|VSS_VDD);
setup_adc(ADC_CLOCK_INTERNAL);
set_adc_channel(0);
 
// Dalsi inicializace
setup_spi(FALSE);
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1);
setup_timer_1(T1_DISABLED);
setup_comparator(NC_NC_NC_NC);
setup_vref(FALSE);
 
// Inicializace stavovych promennych
StepState=0;
 
// Nastaveni casovace
setup_timer_2(T2_DIV_BY_16,0xFF,1);
 
// Nastveni preruseni od casovace
enable_interrupts(global);
enable_interrupts(int_timer2);
for(;;)
{
 
T=read_adc(ADC_READ_ONLY); // Prectu hodnotu
read_adc(ADC_START_ONLY); // Ostartuji dalsi prevod (na pozadi)
 
//setup_timer_2(T2_DIV_BY_16,T,1);
if(T>0) *0x92=T; // Preload register casovace
 
// Podle prepinacu se hybu
if(input(PIN_B5))
{
if(input(PIN_B4)) StepSetDirection(1); else StepSetDirection(-1);
}
else
{ int1 x; // pomocna promenna aby se volalo spozdeni jen 1x
if (StepState>230) {
if (!input(PIN_B4) && (x))
{
StepSetDirection(0);
delay_ms(500);
x=0;
};
StepSetDirection(-1);
}
if (StepState<30) {
StepSetDirection( 1);
x=1;
}
}
//StepDirection=2;
//for(i=0;i<800;i++)
//{
// StepNext();
// Delay(T);
//}
//delay_ms(10);
//StepDirection=-1;
//for(i=0;i<800;i++)
//{
// StepNext();
// Delay(T);
//}
//delay_ms(10);
 
} // Cyklus for
}
/programy/PIC_C/motory/krokac/KROKAC.H
0,0 → 1,23
#include <16F88.h>
//#device ICD=TRUE
#device adc=8
 
#FUSES NOWDT //No Watch Dog Timer
#FUSES RC //Resistor/Capacitor Osc with CLKOUT
#FUSES NOPUT //No Power Up Timer
#FUSES MCLR //Master Clear pin enabled
#FUSES NOBROWNOUT //No brownout reset
#FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O
#FUSES NOCPD //No EE protection
#FUSES NOWRT //Program memory not write protected
//#FUSES DEBUG //Debug mode for use with ICD
#FUSES NOPROTECT //Code not protected from reading
#FUSES FCMEN //Fail-safe clock monitor enabled
#FUSES IESO //Internal External Switch Over mode enabled
 
#use delay(clock=4000000)
#define MOTORA PIN_B0
#define MOTORB PIN_B1
#define MOTORC PIN_B2
#define MOTORD PIN_B3
 
/programy/PIC_C/motory/krokac/KROKAC.HEX
0,0 → 1,44
:1000000000308A0098280000FF00030E8301A10041
:100010007F08A0000A08A8008A01A00E0408A20018
:100020007708A3007808A4007908A5007A08A6003C
:100030007B08A700831383128C308400801C222845
:100040008C183528220884002308F7002408F800BB
:100050002508F9002608FA002708FB0028088A006E
:10006000210E8300FF0E7F0E09008A1143280A101B
:100070008A100A118207013405340434063402342C
:100080000A34083409342A082907A900290807393D
:10009000B20032083720F800B2003218512806109A
:1000A00052280614831606108312B2185928861097
:1000B0005A28861483168610831232196128061175
:1000C00062280615831606118312B2196928861153
:1000D0006A2886158316861183128C108A112228AD
:1000E000B01B78283008013C031878280130B00094
:1000F0003008803A7E3C031C7F28FF30B000300877
:10010000AA00003431308400000803199628013019
:10011000F800F701F70B8A28F80B89284A30F70016
:10012000F70B902800000000800B87288A113029E7
:1001300084011F30830583161F129F121B0880390C
:100140009B0007309C001C0883120D13603083163F
:100150008F000610831206108316861083128610F5
:1001600083160611831206118316861183128611D7
:10017000831681131F129F121B08803901389B00C0
:100180001F1383121F179F1783169F1383121F14A9
:100190000030F8001F08C73978049F0094128316B6
:1001A0000611861406120030831294008316940000
:1001B0000108C7390838810083129001073083167F
:1001C0009C0005080330F700F70BE4281C08831295
:1001D0000D1383169D018312A9010030F800063823
:1001E0009200FF3083169200C03083128B04831676
:1001F0008C1483121F1DFE288316F9281E08AC01DB
:10020000AB001F15AB08031D0829AC0803190C2906
:100210002B08831692008312831686168312861E7D
:100220001E29831606168312061E1A290130B000F5
:1002300070201D29FF30B00070203E292908E63CBF
:1002400003183629831606168312061A33292F1C23
:100250003329B00170200230B000FA30B10082289A
:10026000B00B2D292F10FF30B000702029081D3C45
:10027000031C3E290130B00070202F148316F9288A
:02028000630019
:04400E003B3FFF3FF6
:00000001FF
;PIC16F88
/programy/PIC_C/motory/krokac/KROKAC.LST
0,0 → 1,495
CCS PCM C Compiler, Version 3.234, 27853 16-X-05 21:12
 
Filename: C:\MIHO_DAT\KROKAC\krokac.LST
 
ROM used: 321 words (8%)
Largest free fragment is 2048
RAM used: 21 (12%) at main() level
24 (14%) worst case
Stack: 3 worst case (1 in main + 2 for interrupts)
 
*
0000: MOVLW 00
0001: MOVWF 0A
0002: GOTO 098
0003: NOP
0004: MOVWF 7F
0005: SWAPF 03,W
0006: CLRF 03
0007: MOVWF 21
0008: MOVF 7F,W
0009: MOVWF 20
000A: MOVF 0A,W
000B: MOVWF 28
000C: CLRF 0A
000D: SWAPF 20,F
000E: MOVF 04,W
000F: MOVWF 22
0010: MOVF 77,W
0011: MOVWF 23
0012: MOVF 78,W
0013: MOVWF 24
0014: MOVF 79,W
0015: MOVWF 25
0016: MOVF 7A,W
0017: MOVWF 26
0018: MOVF 7B,W
0019: MOVWF 27
001A: BCF 03.7
001B: BCF 03.5
001C: MOVLW 8C
001D: MOVWF 04
001E: BTFSS 00.1
001F: GOTO 022
0020: BTFSC 0C.1
0021: GOTO 035
0022: MOVF 22,W
0023: MOVWF 04
0024: MOVF 23,W
0025: MOVWF 77
0026: MOVF 24,W
0027: MOVWF 78
0028: MOVF 25,W
0029: MOVWF 79
002A: MOVF 26,W
002B: MOVWF 7A
002C: MOVF 27,W
002D: MOVWF 7B
002E: MOVF 28,W
002F: MOVWF 0A
0030: SWAPF 21,W
0031: MOVWF 03
0032: SWAPF 7F,F
0033: SWAPF 7F,W
0034: RETFIE
0035: BCF 0A.3
0036: GOTO 043
.................... #include "C:\MIHO_DAT\KROKAC\krokac.h"
.................... #include <16F88.h>
.................... //////// Standard Header file for the PIC16F88 device ////////////////
.................... #device PIC16F88
.................... #list
....................
.................... //#device ICD=TRUE
.................... #device adc=8
....................
.................... #FUSES NOWDT //No Watch Dog Timer
.................... #FUSES RC //Resistor/Capacitor Osc with CLKOUT
.................... #FUSES NOPUT //No Power Up Timer
.................... #FUSES MCLR //Master Clear pin enabled
.................... #FUSES NOBROWNOUT //No brownout reset
.................... #FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O
.................... #FUSES NOCPD //No EE protection
.................... #FUSES NOWRT //Program memory not write protected
.................... //#FUSES DEBUG //Debug mode for use with ICD
.................... #FUSES NOPROTECT //Code not protected from reading
.................... #FUSES FCMEN //Fail-safe clock monitor enabled
.................... #FUSES IESO //Internal External Switch Over mode enabled
....................
.................... #use delay(clock=4000000)
*
0082: MOVLW 31
0083: MOVWF 04
0084: MOVF 00,W
0085: BTFSC 03.2
0086: GOTO 096
0087: MOVLW 01
0088: MOVWF 78
0089: CLRF 77
008A: DECFSZ 77,F
008B: GOTO 08A
008C: DECFSZ 78,F
008D: GOTO 089
008E: MOVLW 4A
008F: MOVWF 77
0090: DECFSZ 77,F
0091: GOTO 090
0092: NOP
0093: NOP
0094: DECFSZ 00,F
0095: GOTO 087
0096: BCF 0A.3
0097: GOTO 130 (RETURN)
.................... #define MOTORA PIN_B0
.................... #define MOTORB PIN_B1
.................... #define MOTORC PIN_B2
.................... #define MOTORD PIN_B3
....................
....................
....................
....................
.................... unsigned int StepState; // Vnitrni promenna kroku
.................... signed int StepDirection; // Smer +1/0/-1
....................
.................... byte const StepTab[8]={ // Tabulka pro krokovy motor
.................... 0b0001, // 0
.................... 0b0101, // 1
.................... 0b0100, // 2
.................... 0b0110, // 3
.................... 0b0010, // 4
.................... 0b1010, // 5
.................... 0b1000 // 6
.................... 0b1001, // 7
.................... };
....................
.................... #INT_TIMER2
.................... void StepNext()
.................... {
.................... unsigned int i;
....................
.................... StepState+=StepDirection; // posun se na dalsi krok
*
0043: MOVF 2A,W
0044: ADDWF 29,W
0045: MOVWF 29
.................... i=StepState&0b111; // vezmi spodni 3 bity stavu
0046: MOVF 29,W
0047: ANDLW 07
0048: MOVWF 32
.................... i=StepTab[i]; // prekoduj pomoci tabulky
0049: MOVF 32,W
004A: CALL 037
004B: MOVWF 78
004C: MOVWF 32
.................... output_bit(MOTORA,i&0b0001); // aktivuj jednotlive vystupy
004D: BTFSC 32.0
004E: GOTO 051
004F: BCF 06.0
0050: GOTO 052
0051: BSF 06.0
0052: BSF 03.5
0053: BCF 06.0
.................... output_bit(MOTORB,i&0b0010);
0054: BCF 03.5
0055: BTFSC 32.1
0056: GOTO 059
0057: BCF 06.1
0058: GOTO 05A
0059: BSF 06.1
005A: BSF 03.5
005B: BCF 06.1
.................... output_bit(MOTORC,i&0b0100);
005C: BCF 03.5
005D: BTFSC 32.2
005E: GOTO 061
005F: BCF 06.2
0060: GOTO 062
0061: BSF 06.2
0062: BSF 03.5
0063: BCF 06.2
.................... output_bit(MOTORD,i&0b1000);
0064: BCF 03.5
0065: BTFSC 32.3
0066: GOTO 069
0067: BCF 06.3
0068: GOTO 06A
0069: BSF 06.3
006A: BSF 03.5
006B: BCF 06.3
.................... }
....................
....................
006C: BCF 03.5
006D: BCF 0C.1
006E: BCF 0A.3
006F: GOTO 022
.................... void StepSetDirection(signed int Direction)
.................... {
.................... if(Direction> 1) Direction= 1;
0070: BTFSC 30.7
0071: GOTO 078
0072: MOVF 30,W
0073: SUBLW 01
0074: BTFSC 03.0
0075: GOTO 078
0076: MOVLW 01
0077: MOVWF 30
.................... if(Direction<-1) Direction=-1;
0078: MOVF 30,W
0079: XORLW 80
007A: SUBLW 7E
007B: BTFSS 03.0
007C: GOTO 07F
007D: MOVLW FF
007E: MOVWF 30
.................... StepDirection=Direction;
007F: MOVF 30,W
0080: MOVWF 2A
.................... }
0081: RETLW 00
....................
....................
.................... void StepSetTime(unsigned int16 Time)
.................... {
....................
.................... }
....................
.................... void Delay(unsigned int16 Time)
.................... {
.................... while(Time>255) {Time-=256;delay_us(256);};
.................... if(Time!=0) delay_us(Time);
.................... }
....................
....................
.................... void main()
.................... {
*
0098: CLRF 04
0099: MOVLW 1F
009A: ANDWF 03,F
009B: BSF 03.5
009C: BCF 1F.4
009D: BCF 1F.5
009E: MOVF 1B,W
009F: ANDLW 80
00A0: MOVWF 1B
00A1: MOVLW 07
00A2: MOVWF 1C
00A3: MOVF 1C,W
00A4: BCF 03.5
00A5: BCF 0D.6
.................... unsigned int16 T;
.................... unsigned long int i;
....................
.................... // Nastav pracovni frekvenci procesoru
.................... setup_oscillator(OSC_4MHZ);
00A6: MOVLW 60
00A7: BSF 03.5
00A8: MOVWF 0F
....................
.................... // Vypni motorovy vystup
.................... output_low(MOTORA);
00A9: BCF 06.0
00AA: BCF 03.5
00AB: BCF 06.0
.................... output_low(MOTORB);
00AC: BSF 03.5
00AD: BCF 06.1
00AE: BCF 03.5
00AF: BCF 06.1
.................... output_low(MOTORC);
00B0: BSF 03.5
00B1: BCF 06.2
00B2: BCF 03.5
00B3: BCF 06.2
.................... output_low(MOTORD);
00B4: BSF 03.5
00B5: BCF 06.3
00B6: BCF 03.5
00B7: BCF 06.3
....................
.................... // Vstupy s pull-up odporem
.................... port_b_pullups(TRUE);
00B8: BSF 03.5
00B9: BCF 01.7
....................
.................... // Inicializace A/D prevodniku
.................... setup_adc_ports(sAN0|VSS_VDD);
00BA: BCF 1F.4
00BB: BCF 1F.5
00BC: MOVF 1B,W
00BD: ANDLW 80
00BE: IORLW 01
00BF: MOVWF 1B
.................... setup_adc(ADC_CLOCK_INTERNAL);
00C0: BCF 1F.6
00C1: BCF 03.5
00C2: BSF 1F.6
00C3: BSF 1F.7
00C4: BSF 03.5
00C5: BCF 1F.7
00C6: BCF 03.5
00C7: BSF 1F.0
.................... set_adc_channel(0);
00C8: MOVLW 00
00C9: MOVWF 78
00CA: MOVF 1F,W
00CB: ANDLW C7
00CC: IORWF 78,W
00CD: MOVWF 1F
....................
.................... // Dalsi inicializace
.................... setup_spi(FALSE);
00CE: BCF 14.5
00CF: BSF 03.5
00D0: BCF 06.2
00D1: BSF 06.1
00D2: BCF 06.4
00D3: MOVLW 00
00D4: BCF 03.5
00D5: MOVWF 14
00D6: BSF 03.5
00D7: MOVWF 14
.................... setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1);
00D8: MOVF 01,W
00D9: ANDLW C7
00DA: IORLW 08
00DB: MOVWF 01
.................... setup_timer_1(T1_DISABLED);
00DC: BCF 03.5
00DD: CLRF 10
.................... setup_comparator(NC_NC_NC_NC);
00DE: MOVLW 07
00DF: BSF 03.5
00E0: MOVWF 1C
00E1: MOVF 05,W
00E2: MOVLW 03
00E3: MOVWF 77
00E4: DECFSZ 77,F
00E5: GOTO 0E4
00E6: MOVF 1C,W
00E7: BCF 03.5
00E8: BCF 0D.6
.................... setup_vref(FALSE);
00E9: BSF 03.5
00EA: CLRF 1D
....................
.................... // Inicializace stavovych promennych
.................... StepState=0;
00EB: BCF 03.5
00EC: CLRF 29
....................
.................... // Nastaveni casovace
.................... setup_timer_2(T2_DIV_BY_16,0xFF,1);
00ED: MOVLW 00
00EE: MOVWF 78
00EF: IORLW 06
00F0: MOVWF 12
00F1: MOVLW FF
00F2: BSF 03.5
00F3: MOVWF 12
....................
.................... // Nastveni preruseni od casovace
.................... enable_interrupts(global);
00F4: MOVLW C0
00F5: BCF 03.5
00F6: IORWF 0B,F
.................... enable_interrupts(int_timer2);
00F7: BSF 03.5
00F8: BSF 0C.1
....................
.................... for(;;)
.................... {
....................
.................... T=read_adc(ADC_READ_ONLY); // Prectu hodnotu
00F9: BCF 03.5
00FA: BTFSS 1F.2
00FB: GOTO 0FE
00FC: BSF 03.5
00FD: GOTO 0F9
00FE: MOVF 1E,W
00FF: CLRF 2C
0100: MOVWF 2B
.................... read_adc(ADC_START_ONLY); // Ostartuji dalsi prevod (na pozadi)
0101: BSF 1F.2
....................
.................... //setup_timer_2(T2_DIV_BY_16,T,1);
.................... if(T>0) *0x92=T; // Preload register casovace
0102: MOVF 2B,F
0103: BTFSS 03.2
0104: GOTO 108
0105: MOVF 2C,F
0106: BTFSC 03.2
0107: GOTO 10C
0108: MOVF 2B,W
0109: BSF 03.5
010A: MOVWF 12
010B: BCF 03.5
....................
.................... // Podle prepinacu se hybu
.................... if(input(PIN_B5))
010C: BSF 03.5
010D: BSF 06.5
010E: BCF 03.5
010F: BTFSS 06.5
0110: GOTO 11E
.................... {
.................... if(input(PIN_B4)) StepSetDirection(1); else StepSetDirection(-1);
0111: BSF 03.5
0112: BSF 06.4
0113: BCF 03.5
0114: BTFSS 06.4
0115: GOTO 11A
0116: MOVLW 01
0117: MOVWF 30
0118: CALL 070
0119: GOTO 11D
011A: MOVLW FF
011B: MOVWF 30
011C: CALL 070
.................... }
.................... else
011D: GOTO 13E
.................... { int1 x; // pomocna promenna aby se volalo spozdeni jen 1x
.................... if (StepState>230) {
011E: MOVF 29,W
011F: SUBLW E6
0120: BTFSC 03.0
0121: GOTO 136
.................... if (!input(PIN_B4) && (x))
0122: BSF 03.5
0123: BSF 06.4
0124: BCF 03.5
0125: BTFSC 06.4
0126: GOTO 133
0127: BTFSS 2F.0
0128: GOTO 133
.................... {
.................... StepSetDirection(0);
0129: CLRF 30
012A: CALL 070
.................... delay_ms(500);
012B: MOVLW 02
012C: MOVWF 30
012D: MOVLW FA
012E: MOVWF 31
012F: GOTO 082
0130: DECFSZ 30,F
0131: GOTO 12D
.................... x=0;
0132: BCF 2F.0
.................... };
.................... StepSetDirection(-1);
0133: MOVLW FF
0134: MOVWF 30
0135: CALL 070
.................... }
.................... if (StepState<30) {
0136: MOVF 29,W
0137: SUBLW 1D
0138: BTFSS 03.0
0139: GOTO 13E
.................... StepSetDirection( 1);
013A: MOVLW 01
013B: MOVWF 30
013C: CALL 070
.................... x=1;
013D: BSF 2F.0
.................... }
.................... }
.................... //StepDirection=2;
.................... //for(i=0;i<800;i++)
.................... //{
.................... // StepNext();
.................... // Delay(T);
.................... //}
.................... //delay_ms(10);
.................... //StepDirection=-1;
.................... //for(i=0;i<800;i++)
.................... //{
.................... // StepNext();
.................... // Delay(T);
.................... //}
.................... //delay_ms(10);
....................
.................... } // Cyklus for
013E: BSF 03.5
013F: GOTO 0F9
....................
.................... }
....................
0140: SLEEP
 
Configuration Fuses:
Word 1: 3F3B NOWDT NOPUT MCLR NOBROWNOUT NOLVP NOCPD NOWRT NODEBUG CCPB0 NOPROTECT RC
Word 2: 3FFF FCMEN IESO
/programy/PIC_C/motory/krokac/KROKAC.PJT
0,0 → 1,39
[PROJECT]
Target=krokac.HEX
Development_Mode=
Processor=0x688F
ToolSuite=CCS
 
[Directories]
Include=C:\PROGRAM FILES\PICC_3_234\devices\;C:\PROGRAM FILES\P
Library=
LinkerScript=
 
[Target Data]
FileList=krokac.c;
BuildTool=C-COMPILER
OptionString=+FM
AdditionalOptionString=
BuildRequired=1
 
[krokac.c]
Type=4
Path=
FileList=
BuildTool=
OptionString=
AdditionalOptionString=
 
[mru-list]
1=krokac.c
 
[Windows]
0=0000 krokac.c 0 0 796 451 3 0
 
[Opened Files]
1=C:\MIHO_DAT\KROKAC\krokac.c
2=C:\MIHO_DAT\KROKAC\krokac.h
3=C:\PROGRAM FILES\PICC_3_234\devices\16F88.h
4=C:\MIHO_DAT\KROKAC\krokac.lst
5=
 
/programy/PIC_C/motory/menice/Run.BAT
0,0 → 1,8
@echo off
:loop
picpgr reset PIC16F84
picpgr run
pause
picpgr stop
pause
goto loop
/programy/PIC_C/motory/menice/main.BAK
0,0 → 1,21
#include "D:\@Kaklik\programy\PIC_C\motory\menice\main.h"
 
#DEFINE L1 pin_A0
#DEFINE L2 pin_A1
 
void main()
{
output_low(L1);
output_low(L2);
while(true)
{
output_high(L1);
output_low(L2);
Delay_ms(16);
output_low(L1);
output_high(L2);
Delay_ms(16);
}
}
/programy/PIC_C/motory/menice/main.HEX
0,0 → 1,11
:1000000000308A00192800000F308400000803190E
:10001000182801308D008C018C0B0C288D0B0B28BF
:100020004A308C008C0B122800000000800B09283D
:10003000003484011F3083058316051083120510D8
:100040008316851083128510831685108312851000
:10005000831605108312051411308F0004208316B7
:100060000510831205108316851083128514113034
:080070008F0004202428630026
:02400E00FE3F73
:00000001FF
;PIC16F84
/programy/PIC_C/motory/menice/main.LST
0,0 → 1,102
CCS PCW C Compiler, Version 3.110, 15448
 
Filename: d:\@kaklik\programy\pic_c\motory\menice\main.LST
 
ROM used: 60 (6%)
Largest free fragment is 964
RAM used: 2 (3%) at main() level
3 (4%) worst case
Stack: 1 locations
 
*
0000: MOVLW 00
0001: MOVWF 0A
0002: GOTO 019
0003: NOP
.................... #include "D:\@Kaklik\programy\PIC_C\motory\menice\main.h"
.................... #include <16F84.h>
.................... //////// Standard Header file for the PIC16F84 device ////////////////
.................... #device PIC16F84
.................... #list
....................
.................... #use delay(clock=4000000)
0004: MOVLW 0F
0005: MOVWF 04
0006: MOVF 00,W
0007: BTFSC 03.2
0008: GOTO 018
0009: MOVLW 01
000A: MOVWF 0D
000B: CLRF 0C
000C: DECFSZ 0C,F
000D: GOTO 00C
000E: DECFSZ 0D,F
000F: GOTO 00B
0010: MOVLW 4A
0011: MOVWF 0C
0012: DECFSZ 0C,F
0013: GOTO 012
0014: NOP
0015: NOP
0016: DECFSZ 00,F
0017: GOTO 009
0018: RETLW 00
.................... #fuses HS,WDT
....................
....................
....................
.................... #DEFINE L1 pin_A0
.................... #DEFINE L2 pin_A1
....................
.................... void main()
.................... {
0019: CLRF 04
001A: MOVLW 1F
001B: ANDWF 03,F
.................... output_low(L1);
001C: BSF 03.5
001D: BCF 05.0
001E: BCF 03.5
001F: BCF 05.0
.................... output_low(L2);
0020: BSF 03.5
0021: BCF 05.1
0022: BCF 03.5
0023: BCF 05.1
....................
.................... while(true)
.................... {
.................... output_low(L2);
0024: BSF 03.5
0025: BCF 05.1
0026: BCF 03.5
0027: BCF 05.1
.................... output_high(L1);
0028: BSF 03.5
0029: BCF 05.0
002A: BCF 03.5
002B: BSF 05.0
.................... Delay_ms(17);
002C: MOVLW 11
002D: MOVWF 0F
002E: CALL 004
.................... output_low(L1);
002F: BSF 03.5
0030: BCF 05.0
0031: BCF 03.5
0032: BCF 05.0
.................... output_high(L2);
0033: BSF 03.5
0034: BCF 05.1
0035: BCF 03.5
0036: BSF 05.1
.................... Delay_ms(17);
0037: MOVLW 11
0038: MOVWF 0F
0039: CALL 004
....................
.................... }
003A: GOTO 024
.................... }
....................
003B: SLEEP
/programy/PIC_C/motory/menice/main.PJT
0,0 → 1,32
[PROJECT]
Target=main.HEX
Development_Mode=
Processor=0x684A
ToolSuite=CCS
 
[Directories]
Include=C:\PROGRAM FILES\PICC\devices\;C:\PROGRAM FILES\PICC\dr;
Library=
LinkerScript=
 
[Target Data]
FileList=main.c;
BuildTool=C-COMPILER
OptionString=+FM
AdditionalOptionString=
BuildRequired=1
 
[main.c]
Type=4
Path=
FileList=
BuildTool=
OptionString=
AdditionalOptionString=
 
[mru-list]
1=main.c
 
[Windows]
0=0000 main.c 0 0 796 451 3 0
 
/programy/PIC_C/motory/menice/main.SYM
0,0 → 1,13
00C @SCRATCH
00D @SCRATCH
00D _RETURN_
00F delay_ms.P1
delay_us.P1
 
0004 delay_ms
0019 main
 
Project Files:
d:\@kaklik\programy\pic_c\motory\menice\main.c
D:\@Kaklik\programy\PIC_C\motory\menice\main.h
C:\PROGRAM FILES\PICC\devices\16F84.h
/programy/PIC_C/motory/menice/main.c
0,0 → 1,21
#include "D:\@Kaklik\programy\PIC_C\motory\menice\main.h"
 
#DEFINE L1 pin_A0
#DEFINE L2 pin_A1
 
void main()
{
output_low(L1);
output_low(L2);
while(true)
{
output_low(L2);
output_high(L1);
Delay_ms(17);
output_low(L1);
output_high(L2);
Delay_ms(17);
}
}
/programy/PIC_C/motory/menice/main.cod
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property
/programy/PIC_C/motory/menice/main.err
0,0 → 1,0
No Errors
/programy/PIC_C/motory/menice/main.h
0,0 → 1,4
#include <16F84.h>
#use delay(clock=4000000)
#fuses HS,WDT
 
/programy/PIC_C/motory/menice/main.sta
0,0 → 1,28
 
ROM used: 60 (6%)
964 (94%) including unused fragments
 
0 Average locations per line
6 Average locations per statement
 
RAM used: 2 (3%) at main() level
3 (4%) worst case
 
Lines Stmts % Files
----- ----- --- -----
22 10 100 d:\@kaklik\programy\pic_c\motory\menice\main.c
5 0 0 D:\@Kaklik\programy\PIC_C\motory\menice\main.h
111 0 0 C:\PROGRAM FILES\PICC\devices\16F84.h
----- -----
276 20 Total
 
Page ROM % RAM Functions:
---- --- --- --- ----------
0 21 35 1 delay_ms
0 35 58 0 main
 
Segment Used Free
--------- ---- ----
0000-0003 4 0
0004-03FF 56 964
 
/programy/PIC_C/motory/menice/main.tre
0,0 → 1,5
ÀÄmain
ÀÄmain 0/35 Ram=0
ÃÄ??0??
ÃÄdelay_ms 0/21 Ram=1
ÀÄdelay_ms 0/21 Ram=1
/programy/PIC_C/motory/menice/prg.bat
0,0 → 1,6
call picpgr stop
call picpgr erase pic16f84
call picpgr program main.hex hex pic16f84
call picpgr run
pause
call picpgr stop
/programy/PIC_C/motory/menice/vssver.scc
Cannot display: file marked as a binary type.
svn:mime-type = application/octet-stream
Property changes:
Added: svn:mime-type
+application/octet-stream
\ No newline at end of property