0,0 → 1,234 |
#include ".\main.h" |
|
#define KOLMO1 225 // predni kolecko sroubem dopredu |
#define KOLMO2 30 // predni kolecko je hlavou sroubu dozadu |
#define STRED 128 // sredni poloha zataceciho kolecka |
#define BEAR1 10 // 3 stupne zataceni |
#define BEAR2 25 |
#define BEAR3 45 |
#define R 100 // Rozumna rychlost |
#define R17 200 // X nasobek rozumne rychlosti |
#define PRED_CIHLOU 100 // rychlost pri dalkove detekci cihly |
#define L2 2 // cara vlevo |
#define L3 3 // cara vlevo |
#define S 0 // cara mezi sensory |
#define R2 -2 // cara vpravo |
#define R3 -3 // cara vpravo |
|
// servo |
#define SERVO PIN_B5 |
|
// kroutitka |
#define CERVENA 4 // AN4 |
//#define CERNA 5 // AN5 |
//#define ZELENA 6 // AN6 |
#define MODRA 2 // AN2 |
|
// IR |
#define IRTX PIN_B2 |
#define CIHLA PIN_A3 |
|
//motory |
#define FR output_low(PIN_A7); output_high(PIN_A6) // Vpred |
#define FL output_low(PIN_A1); output_high(PIN_A0) |
#define BR output_low(PIN_A6); output_high(PIN_A7) // Vzad |
#define BL output_low(PIN_A0); output_high(PIN_A1) |
#define STOPR output_low(PIN_A6);output_low(PIN_A7) |
#define STOPL output_low(PIN_A0);output_low(PIN_A1) |
|
//HID |
#define LED1 PIN_B1 //oranzova |
#define LED2 PIN_B2 //zluta |
|
#define STROBE PIN_B0 |
//#define SW1 PIN_A2 // Motory On/off |
|
unsigned int8 sensors; // pomocna promenna pro cteni cidel na caru |
signed int8 line = S; // na ktere strane byla detekovana cara |
unsigned int8 uhel; // urcuje aktualni uhel zataceni |
unsigned int8 speed; // maximalni povolena rychlost |
unsigned int8 turn; // rychlost toceni |
unsigned int8 rovinka; // pocitadlo na zjisteni rovinky |
|
signed int16 Lmotor; // promene, ktere urcuji velikost vykonu na levem |
signed int16 Rmotor; // a pravem motoru |
|
// makro pro PWM pro motory |
#define GO(motor, direction, power) if(get_timer0()<=power) \ |
{direction##motor;} else {stop##motor;} |
//////////////////////////////////////////////////////////////////////////////// |
#int_TIMER2 |
TIMER2_isr() // ovladani serva |
{ |
unsigned int8 n; |
|
output_high(SERVO); |
delay_us(1000); |
for(n=uhel; n>0; n--) Delay_us(2); |
output_low(SERVO); |
} |
//////////////////////////////////////////////////////////////////////////////// |
#include ".\objizdka_centrovani.c" |
//////////////////////////////////////////////////////////////////////////////// |
void main() |
{ |
unsigned int8 n; |
unsigned int8 i,j; |
unsigned int8 last_sensors; |
unsigned int8 RozumnaRychlost; |
|
setup_adc_ports(sAN5|sAN2|sAN4|sAN6|VSS_VDD); // AD pro kroutitka |
setup_adc(ADC_CLOCK_INTERNAL); |
setup_spi(SPI_MASTER|SPI_H_TO_L|SPI_XMIT_L_TO_H|SPI_CLK_DIV_16); |
setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); |
setup_timer_1(T1_DISABLED|T1_DIV_BY_8); |
setup_timer_2(T2_DIV_BY_16,140,16); |
setup_oscillator(OSC_8MHZ|OSC_INTRC); |
|
STOPR; STOPL; // zastav motory |
Lmotor=0;Rmotor=0; |
|
uhel = STRED; // nastav zadni kolecko na stred |
rovinka = 0; |
|
enable_interrupts(INT_TIMER2); |
enable_interrupts(GLOBAL); |
|
output_low(IRTX); // zapni IR vysilac |
|
delay_ms(2000); // musime pockat na diagnostiku slave CPU |
|
//nastaveni rychlosti |
set_adc_channel(CERVENA); |
|
Delay_ms(1); |
RozumnaRychlost=R+(read_adc()>>2); // rychlost rovne +63; kroutitko dava 0-63 |
set_adc_channel(MODRA); |
Delay_ms(1); |
turn=speed-32+(read_adc()>>2); // rychlost toceni +-32; kroutitko dava 0-63 |
|
speed=R17; |
|
while(true) |
{ |
|
GO(L,F,Lmotor);GO(R,F,Rmotor); // zapni motory PWM podle promenych Lmotor a Rmotor |
|
delay_us(2000); // cekani na SLAVE, nez pripravi data od cidel |
|
last_sensors=sensors; |
|
output_low(STROBE); // vypni zobrazovani na posuvnem registru |
sensors = spi_read(0); // cteni senzoru |
sensors=~sensors; // neguj prijata data |
output_high(STROBE); // zobraz data na posuvnem registru |
|
i=0; // havarijni kod |
for (n=0; n<=6; n++) |
{ |
if(bit_test(sensors,n)) i++; |
} |
if (i>4) // zastavi, kdyz je cerno pod vice nez tremi cidly |
{ |
BL; BR; |
delay_ms(300); |
STOPR; STOPL; |
While(true); |
}; |
|
if (bit_test(sensors,7)) // detekce cihly |
{ |
BR;BL; |
Delay_ms(400); |
STOPR;STOPL; |
{ |
Delay_ms(100); |
cikcak(); |
delay_ms(100); |
objizdka(); // objede cihlu |
} |
} |
|
if (speed > RozumnaRychlost) speed--; // postupne zpomaleni na Roz. Rychl. |
|
if(bit_test(sensors,3)) //...|...// |
{ |
uhel=STRED; |
Lmotor=speed; |
Rmotor=speed; |
line=S; |
if (rovinka < 255) rovinka++; |
continue; |
} |
|
// z duvodu zkraceni doby reakce se cidla nevyhodnocuji poporade ale od krajnich k prostrednimu |
if(bit_test(sensors,0)) //|......// |
{ |
uhel=STRED - BEAR3; |
Lmotor=0; |
Rmotor=turn; |
line=L3; |
continue; |
} |
|
if(bit_test(sensors,6)) //......|// |
{ |
uhel=STRED + BEAR3; |
Rmotor=0; |
Lmotor=turn; |
line=R3; |
continue; |
} |
|
if(bit_test(sensors,1)) //.|.....// |
{ |
uhel=STRED - BEAR2; |
Lmotor=speed-70; |
Rmotor=speed; |
line=L2; |
continue; |
} |
|
if(bit_test(sensors,5)) //.....|.// |
{ |
uhel=STRED + BEAR2; |
Rmotor=speed-70; |
Lmotor=speed; |
line=R2; |
continue; |
} |
|
if (bit_test(sensors,2)) //..|....// |
{ |
uhel=STRED - BEAR1; |
Lmotor=speed-20; |
Rmotor=speed; |
line=L2; |
if (rovinka<255) rovinka++; |
continue; |
} |
|
if (bit_test(sensors,4)) //....|..// |
{ |
uhel=STRED + BEAR1; |
Rmotor=speed-20; |
Lmotor=speed; |
line=L2; |
if (rovinka<255) rovinka++; |
continue; |
} |
|
|
if ((L3==line) || (R3==line)) // Brzdeni pri vyjeti z trate |
{ |
if (rovinka>50) |
{ |
BL; BR; |
Delay_ms(100); |
if (rovinka > 250 || speed > 170) delay_ms(50); |
}; |
rovinka=0; |
speed=R17; |
}; |
} |
} |