Subversion Repositories svnkaklik

/*
 * Board-specific setup code for the ATNGW100 Network Gateway
 *
 * Copyright (C) 2005-2006 Atmel Corporation
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */
#include <linux/clk.h>
#include <linux/etherdevice.h>
#include <linux/i2c-gpio.h>
#include <linux/init.h>
#include <linux/linkage.h>
#include <linux/platform_device.h>
#include <linux/types.h>
#include <linux/leds.h>
#include <linux/spi/spi.h>

#include <asm/io.h>
#include <asm/setup.h>

#include <asm/arch/at32ap7000.h>
#include <asm/arch/board.h>
#include <asm/arch/init.h>
#include <asm/arch/portmux.h>

/* Initialized by bootloader-specific startup code. */
struct tag *bootloader_tags __initdata;

struct eth_addr {
        u8 addr[6];
};
static struct eth_addr __initdata hw_addr[2];
static struct eth_platform_data __initdata eth_data[2];

static struct spi_board_info spi0_board_info[] __initdata = {
        {
                .modalias       = "mtd_dataflash",
                .max_speed_hz   = 10000000,
                .chip_select    = 0,
        },
};

static struct mci_platform_data __initdata mci0_data = {
        .detect_pin     = GPIO_PIN_PC(25),
        .wp_pin         = GPIO_PIN_PE(0),
};

/*
 * The next two functions should go away as the boot loader is
 * supposed to initialize the macb address registers with a valid
 * ethernet address. But we need to keep it around for a while until
 * we can be reasonably sure the boot loader does this.
 *
 * The phy_id is ignored as the driver will probe for it.
 */
static int __init parse_tag_ethernet(struct tag *tag)
{
        int i;

        i = tag->u.ethernet.mac_index;
        if (i < ARRAY_SIZE(hw_addr))
                memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address,
                       sizeof(hw_addr[i].addr));

        return 0;
}
__tagtable(ATAG_ETHERNET, parse_tag_ethernet);

static void __init set_hw_addr(struct platform_device *pdev)
{
        struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
        const u8 *addr;
        void __iomem *regs;
        struct clk *pclk;

        if (!res)
                return;
        if (pdev->id >= ARRAY_SIZE(hw_addr))
                return;

        addr = hw_addr[pdev->id].addr;
        if (!is_valid_ether_addr(addr))
                return;

        /*
         * Since this is board-specific code, we'll cheat and use the
         * physical address directly as we happen to know that it's
         * the same as the virtual address.
         */
        regs = (void __iomem __force *)res->start;
        pclk = clk_get(&pdev->dev, "pclk");
        if (!pclk)
                return;

        clk_enable(pclk);
        __raw_writel((addr[3] << 24) | (addr[2] << 16)
                     | (addr[1] << 8) | addr[0], regs + 0x98);
        __raw_writel((addr[5] << 8) | addr[4], regs + 0x9c);
        clk_disable(pclk);
        clk_put(pclk);
}

void __init setup_board(void)
{
        at32_map_usart(1, 0);   /* USART 1: /dev/ttyS0, DB9 */
        at32_map_usart(3, 1);   /* USART 3: /dev/ttyS1      */
        at32_setup_serial_console(0);
}

static const struct gpio_led ngw_leds[] = {
        { .name = "sys", .gpio = GPIO_PIN_PA(16), .active_low = 1,
                .default_trigger = "heartbeat",
        },
        { .name = "a", .gpio = GPIO_PIN_PA(19), .active_low = 1, },
        { .name = "b", .gpio = GPIO_PIN_PE(19), .active_low = 1, },
};

static const struct gpio_led_platform_data ngw_led_data = {
        .num_leds =     ARRAY_SIZE(ngw_leds),
        .leds =         (void *) ngw_leds,
};

static struct platform_device ngw_gpio_leds = {
        .name =         "leds-gpio",
        .id =           -1,
        .dev = {
                .platform_data = (void *) &ngw_led_data,
        }
};

#ifdef CONFIG_BOARD_ATNGW100_I2C_GPIO
static struct i2c_gpio_platform_data i2c_gpio_data = {
        .sda_pin        = GPIO_PIN_PA(6),
        .scl_pin        = GPIO_PIN_PA(7),
};

static struct platform_device i2c_gpio_device = {
        .name           = "i2c-gpio",
        .id             = 0,
        .dev            = {
                .platform_data  = &i2c_gpio_data,
        },
};
#endif

static int __init atngw100_init(void)
{
        unsigned        i;

        /*
         * ATNGW100 uses 16-bit SDRAM interface, so we don't need to
         * reserve any pins for it.
         */

        at32_add_system_devices();

        at32_add_device_usart(0);
        at32_add_device_usart(1);

        set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
        set_hw_addr(at32_add_device_eth(1, &eth_data[1]));

        at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
        at32_add_device_mci(0, &mci0_data);
        at32_add_device_usba(0, NULL);

        for (i = 0; i < ARRAY_SIZE(ngw_leds); i++) {
                at32_select_gpio(ngw_leds[i].gpio,
                                AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
        }
        platform_device_register(&ngw_gpio_leds);

#ifdef CONFIG_BOARD_ATNGW100_I2C_GPIO
        at32_select_gpio(i2c_gpio_data.sda_pin, 0);
        at32_select_gpio(i2c_gpio_data.scl_pin, 0);
        platform_device_register(&i2c_gpio_device);
#else
        at32_add_device_twi(0);
#endif
        at32_add_device_ac97c (0);

        return 0;
}
postcore_initcall(atngw100_init);