/******************************************************************************
USB Host Mass Storage Device Driver
This is the Mass Storage Class driver file for a USB Embedded Host device.
This file should be used in a project with usb_host.c to provided the USB
hardware interface.
Acronyms/abbreviations used by this class:
* LUN - Logical Unit Number
* CBW - Command Block Wrapper
* CSW - Command Status Wrapper
To interface with usb_host.c, the routine USBHostMSDClientInitialize() should be
specified as the Initialize() function, and USBHostMSDClientEventHandler() should
be specified as the EventHandler() function in the usbClientDrvTable[] array
declared in usb_config.h.
This driver can be configured to use transfer events from usb_host.c. Transfer
events require more RAM and ROM than polling, but it cuts down or even
eliminates the required polling of the various USBxxxTasks functions. For this
class, USBHostMSDTasks() is compiled out if transfer events from usb_host.c
are used. However, USBHostTasks() still must be called to provide attach,
enumeration, and detach services. If transfer events from usb_host.c
are going to be used, USB_ENABLE_TRANSFER_EVENT should be defined. If transfer
status is going to be polled, USB_ENABLE_TRANSFER_EVENT should not be defined.
This driver can also be configured to provide mass storage transfer events to
the next layer. Generating these events requires a small amount of extra ROM,
but no extra RAM. The layer above this driver must be configured to receive
and respond to the events. If mass storage transfer events are going to be
sent to the next layer, USB_MSD_ENABLE_TRANSFER_EVENT should be defined. If
mass storage transfer status is going to be polled,
USB_MSD_ENABLE_TRANSFER_EVENT should not be defined.
Since mass storage is performed with bulk transfers, USB_SUPPORT_BULK_TRANSFERS
must be defined. For maximum throughput, it is recommended that
ALLOW_MULTIPLE_BULK_TRANSACTIONS_PER_FRAME be defined. For maximum
compatibility with mass storage devices, it is recommended that
ALLOW_MULTIPLE_NAKS_PER_FRAME not be defined.
FileName: usb_host_msd.c
Dependencies: None
Processor: PIC24/dsPIC30/dsPIC33/PIC32MX
Compiler: C30/C32
Company: Microchip Technology, Inc.
Software License Agreement
The software supplied herewith by Microchip Technology Incorporated
(the Company) for its PICmicro® Microcontroller is intended and
supplied to you, the Companys customer, for use solely and
exclusively on Microchip PICmicro Microcontroller products. The
software is owned by the Company and/or its supplier, and is
protected under applicable copyright laws. All rights are reserved.
Any use in violation of the foregoing restrictions may subject the
user to criminal sanctions under applicable laws, as well as to
civil liability for the breach of the terms and conditions of this
license.
THIS SOFTWARE IS PROVIDED IN AN AS IS CONDITION. NO WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED
TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. THE COMPANY SHALL NOT,
IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.
Change History:
Rev Description
---------- ----------------------------------------------------------
2.6 - 2.6a No change
2.7 Fixed issue where a transfer event is incorrectly sent when
transfer events are enabled.
2.7a No change
*******************************************************************************/
#include <stdlib.h>
#include <string.h>
#include "Compiler.h"
#include "GenericTypeDefs.h"
#include "HardwareProfile.h"
#include "USB\usb.h"
#include "USB\usb_host_msd.h"
//#define DEBUG_MODE
#ifdef DEBUG_MODE
#include "uart2.h"
#endif
// *****************************************************************************
// *****************************************************************************
// Section: Configuration
// *****************************************************************************
// *****************************************************************************
// *****************************************************************************
/* Max Number of Supported Devices
This value represents the maximum number of attached devices this class driver
can support. If the user does not define a value, it will be set to 1.
Currently this must be set to 1, due to limitations in the USB Host layer.
*/
#ifndef USB_MAX_MASS_STORAGE_DEVICES
#define USB_MAX_MASS_STORAGE_DEVICES 1
#endif
// *****************************************************************************
// *****************************************************************************
// Section: Constants
// *****************************************************************************
// *****************************************************************************
// *****************************************************************************
// Section: State Machine Constants
// *****************************************************************************
#ifndef USB_ENABLE_TRANSFER_EVENT
#define STATE_MASK 0x00F0 //
#define SUBSTATE_MASK 0x000F //
#define NEXT_STATE 0x0010 //
#define NEXT_SUBSTATE 0x0001 //
#define STATE_DETACHED 0x0000 //
#define STATE_INITIALIZE_DEVICE 0x0010 //
#define SUBSTATE_WAIT_FOR_ENUMERATION 0x0000 //
#define SUBSTATE_SEND_GET_MAX_LUN 0x0001 //
#define SUBSTATE_WAIT_FOR_MAX_LUN 0x0002 //
#define SUBSTATE_GET_MAX_LUN_COMPLETE 0x0003 //
#define STATE_RUNNING 0x0020 //
#define SUBSTATE_HOLDING 0x0000 //
#define SUBSTATE_SEND_CBW 0x0001 //
#define SUBSTATE_CBW_WAIT 0x0002 //
#define SUBSTATE_TRANSFER_DATA 0x0003 //
#define SUBSTATE_TRANSFER_WAIT 0x0004 //
#define SUBSTATE_REQUEST_CSW 0x0005 //
#define SUBSTATE_CSW_WAIT 0x0006 //
#define SUBSTATE_TRANSFER_DONE 0x0007 //
#define STATE_MSD_RESET_RECOVERY 0x0030 //
#define SUBSTATE_SEND_RESET 0x0000 //
#define SUBSTATE_WAIT_FOR_RESET 0x0001 //
#define SUBSTATE_RESET_COMPLETE 0x0002 //
#define STATE_MSD_CLEAR_DATA_IN 0x0040 //
#define SUBSTATE_SEND_CLEAR_IN 0x0000 //
#define SUBSTATE_WAIT_FOR_CLEAR_IN 0x0001 //
#define SUBSTATE_CLEAR_IN_COMPLETE 0x0002 //
#define STATE_MSD_CLEAR_DATA_OUT 0x0050 //
#define SUBSTATE_SEND_CLEAR_OUT 0x0000 //
#define SUBSTATE_WAIT_FOR_CLEAR_OUT 0x0001 //
#define SUBSTATE_CLEAR_OUT_COMPLETE 0x0002 //
#define STATE_HOLDING 0x0060 // Holding due to an error
#else
#define STATE_DETACHED 0x0000 //
#define STATE_WAIT_FOR_MAX_LUN 0x0001 //
#define STATE_RUNNING 0x0002 //
#define STATE_CBW_WAIT 0x0003 //
#define STATE_TRANSFER_WAIT 0x0004 //
#define STATE_CSW_WAIT 0x0005 //
#define STATE_WAIT_FOR_RESET 0x0006 //
#define STATE_WAIT_FOR_CLEAR_IN 0x0007 //
#define STATE_WAIT_FOR_CLEAR_OUT 0x0008 //
#define STATE_HOLDING 0x0009 // Holding due to an error
#define STATE_REQUEST_CSW 0x000A // Dummy state
#endif
// *****************************************************************************
// Section: Other Constants
// *****************************************************************************
#define CBW_SIZE 31 // Number of bytes in the CBW.
#define CSW_SIZE 13 // Number of bytes in the CSW.
#define CSW_RECEIVE_ATTEMPTS 100 // Number of attempts to obtain the CSW.
#define USB_MSD_GET_MAX_LUN 0xFE // Device Request code to get the maximum LUN.
#define USB_MSD_RESET 0xFF // Device Request code to reset the device.
#define USB_MSD_DCBWSIGNATURE 0x43425355ul // Signature value for the CBW.
#define USB_MSD_DCSWSIGNATURE 0x53425355ul // Signature value for the CSW.
#define MARK_RESET_RECOVERY 0x0E // Maintain with USB_MSD_DEVICE_INFO
//******************************************************************************
//******************************************************************************
// Section: Data Structures
//******************************************************************************
//******************************************************************************
// *****************************************************************************
/* USB Mass Storage Device Information
This structure is used to hold all the information about an attached Mass Storage device.
*/
typedef struct _USB_MSD_DEVICE_INFO
{
BYTE blockData[31]; // Data buffer for device communication.
BYTE deviceAddress; // Address of the device on the bus.
BYTE clientDriverID; // Client driver ID for device requests.
BYTE errorCode; // Error code of last error.
BYTE state; // State machine state of the device.
BYTE returnState; // State to return to after performing error handling.
union
{
struct
{
BYTE bfDirection : 1; // Direction of current transfer (0=OUT, 1=IN).
BYTE bfReset : 1; // Flag indicating to perform Mass Storage Reset.
BYTE bfClearDataIN : 1; // Flag indicating to clear the IN endpoint.
BYTE bfClearDataOUT : 1; // Flag indicating to clear the OUT endpoint.
};
BYTE val;
} flags;
BYTE maxLUN; // The maximum Logical Unit Number of the device.
BYTE interface; // Interface number we are using.
BYTE endpointIN; // Bulk IN endpoint.
BYTE endpointOUT; // Bulk OUT endpoint.
BYTE endpointDATA; // Endpoint to use for the current transfer.
BYTE *userData; // Pointer to the user's data buffer.
DWORD userDataLength; // Length of the user's data buffer.
DWORD bytesTransferred; // Number of bytes transferred to/from the user's data buffer.
DWORD dCBWTag; // The value of the dCBWTag to verify against the dCSWtag.
BYTE attemptsCSW; // Number of attempts to retrieve the CSW.
} USB_MSD_DEVICE_INFO;
// *****************************************************************************
/* Command Block Wrapper
This is the structure of the Command Block Wrapper, required at the beginning of
each mass storage transfer.
*/
typedef struct _USB_MSD_CBW
{
DWORD dCBWSignature; // Signature, must be a specific constant.
DWORD dCBWTag; // Transaction tag. Value in the CSW must match.
DWORD dCBWDataTransferLength; // Length of the following data transfer.
union
{
struct
{
BYTE : 7;
BYTE bfDirection : 1; // Direction of data transfer (0=OUT, 1=IN).
};
BYTE val;
} bmCBWflags;
BYTE bCBWLUN; // Logical Unit Number (bits 3:0 only).
BYTE bCBWCBLength; // Length of command block (bits 4:0 only).
BYTE CBWCB[16]; // Command block.
} USB_MSD_CBW;
// *****************************************************************************
/* Command Status Wrapper
This is the structure of the Command Status Wrapper, required at the end of
each mass storage transfer.
*/
typedef struct _USB_MSD_CSW
{
DWORD dCSWSignature; // Signature, must be a specific constant.
DWORD dCSWTag; // Transaction tag. Must match the CBW.
DWORD dCSWDataResidue; // Count of data bytes not transferred.
BYTE dCSWStatus; // Result of requested operation.
} USB_MSD_CSW;
//******************************************************************************
//******************************************************************************
// Section: Local Prototypes
//******************************************************************************
//******************************************************************************
DWORD _USBHostMSD_GetNextTag( void );
void _USBHostMSD_ResetStateJump( BYTE i );
//******************************************************************************
//******************************************************************************
// Section: Macros
//******************************************************************************
//******************************************************************************
#ifndef USB_ENABLE_TRANSFER_EVENT
#define _USBHostMSD_SetNextState() { deviceInfoMSD[i].state = (deviceInfoMSD[i].state & STATE_MASK) + NEXT_STATE; }
#define _USBHostMSD_SetNextSubState() { deviceInfoMSD[i].state += NEXT_SUBSTATE; }
#define _USBHostMSD_TerminateTransfer( error ) { \
deviceInfoMSD[i].errorCode = error; \
deviceInfoMSD[i].state = STATE_RUNNING | SUBSTATE_TRANSFER_DONE; \
}
#else
#ifdef USB_MSD_ENABLE_TRANSFER_EVENT
#define _USBHostMSD_TerminateTransfer( error ) { \
deviceInfoMSD[i].errorCode = error; \
deviceInfoMSD[i].state = STATE_RUNNING; \
usbMediaInterfaceTable.EventHandler( deviceInfoMSD[i].deviceAddress, EVENT_MSD_TRANSFER, NULL, 0 ); \
}
#else
#define _USBHostMSD_TerminateTransfer( error ) { \
deviceInfoMSD[i].errorCode = error; \
deviceInfoMSD[i].state = STATE_RUNNING; \
}
#endif
#endif
//******************************************************************************
//******************************************************************************
// Section: MSD Host External Variables
//******************************************************************************
//******************************************************************************
extern CLIENT_DRIVER_TABLE usbMediaInterfaceTable; // This table contains the initialization
// routine and event handler for the media
// interface layer of the application.
// It is defined in USBConfig.c.
//******************************************************************************
//******************************************************************************
// Section: MSD Host Global Variables
//******************************************************************************
//******************************************************************************
static DWORD dCBWTagNext = 0x12345678ul;
static USB_MSD_DEVICE_INFO deviceInfoMSD[USB_MAX_MASS_STORAGE_DEVICES] __attribute__ ((aligned));
// *****************************************************************************
// *****************************************************************************
// Section: Application Callable Functions
// *****************************************************************************
// *****************************************************************************
/****************************************************************************
Function:
BYTE USBHostMSDDeviceStatus( BYTE deviceAddress )
Description:
This function determines the status of a mass storage device.
Precondition:
None
Parameters:
BYTE deviceAddress - address of device to query
Return Values:
USB_MSD_DEVICE_NOT_FOUND - Illegal device address, or the device is not
an MSD
USB_MSD_INITIALIZING - MSD is attached and in the process of
initializing
USB_MSD_NORMAL_RUNNING - MSD is in normal running mode
USB_MSD_RESETTING_DEVICE - MSD is resetting
USB_MSD_DEVICE_DETACHED - MSD detached. Should not occur
USB_MSD_ERROR_STATE - MSD is holding due to an error. No
communication is allowed.
Other - Return codes from USBHostDeviceStatus() will
also be returned if the device is in the
process of enumerating.
Remarks:
None
***************************************************************************/
BYTE USBHostMSDDeviceStatus( BYTE deviceAddress )
{
BYTE i;
BYTE status;
// Make sure a valid device is being requested.
if ((deviceAddress == 0) || (deviceAddress > 127))
{
return USB_MSD_DEVICE_NOT_FOUND;
}
// Find the correct device.
for (i=0; (i<USB_MAX_MASS_STORAGE_DEVICES) && (deviceInfoMSD[i].deviceAddress != deviceAddress); i++);
if (i == USB_MAX_MASS_STORAGE_DEVICES)
{
return USB_MSD_DEVICE_NOT_FOUND;
}
status = USBHostDeviceStatus( deviceAddress );
if (status != USB_DEVICE_ATTACHED)
{
return status;
}
else
{
// The device is attached and done enumerating. We can get more specific now.
#ifndef USB_ENABLE_TRANSFER_EVENT
switch (deviceInfoMSD[i].state & STATE_MASK)
{
case STATE_INITIALIZE_DEVICE:
return USB_MSD_INITIALIZING;
break;
case STATE_RUNNING:
return USB_MSD_NORMAL_RUNNING;
break;
case STATE_HOLDING:
return USB_MSD_ERROR_STATE;
break;
case STATE_MSD_RESET_RECOVERY:
case STATE_MSD_CLEAR_DATA_IN:
case STATE_MSD_CLEAR_DATA_OUT:
return USB_MSD_RESETTING_DEVICE;
break;
default:
return USB_MSD_DEVICE_DETACHED;
break;
}
#else
switch (deviceInfoMSD[i].state)
{
case STATE_WAIT_FOR_MAX_LUN:
return USB_MSD_INITIALIZING;
break;
case STATE_RUNNING:
case STATE_CBW_WAIT:
case STATE_TRANSFER_WAIT:
case STATE_CSW_WAIT:
case STATE_REQUEST_CSW:
return USB_MSD_NORMAL_RUNNING;
break;
case STATE_HOLDING:
return USB_MSD_ERROR_STATE;
break;
case STATE_WAIT_FOR_RESET:
case STATE_WAIT_FOR_CLEAR_IN:
case STATE_WAIT_FOR_CLEAR_OUT:
return USB_MSD_RESETTING_DEVICE;
break;
default:
return USB_MSD_DEVICE_DETACHED;
break;
}
#endif
}
}
/****************************************************************************
Function:
BYTE USBHostMSDResetDevice( BYTE deviceAddress )
Summary:
This function starts a bulk-only mass storage reset.
Description:
This function starts a bulk-only mass storage reset. A reset can be
issued only if the device is attached and not being initialized.
Precondition:
None
Parameters:
BYTE deviceAddress - Device address
Return Values:
USB_SUCCESS - Reset started
USB_MSD_DEVICE_NOT_FOUND - No device with specified address
USB_MSD_ILLEGAL_REQUEST - Device is in an illegal state for reset
Remarks:
None
***************************************************************************/
BYTE USBHostMSDResetDevice( BYTE deviceAddress )
{
BYTE i;
// Make sure a valid device is being requested.
if ((deviceAddress == 0) || (deviceAddress > 127))
{
return USB_MSD_DEVICE_NOT_FOUND;
}
// Find the correct device.
for (i=0; (i<USB_MAX_MASS_STORAGE_DEVICES) && (deviceInfoMSD[i].deviceAddress != deviceAddress); i++);
if (i == USB_MAX_MASS_STORAGE_DEVICES)
{
return USB_MSD_DEVICE_NOT_FOUND;
}
#ifndef USB_ENABLE_TRANSFER_EVENT
if (((deviceInfoMSD[i].state & STATE_MASK) != STATE_DETACHED) &&
((deviceInfoMSD[i].state & STATE_MASK) != STATE_INITIALIZE_DEVICE))
#else
if ((deviceInfoMSD[i].state == STATE_RUNNING) ||
(deviceInfoMSD[i].state == STATE_HOLDING ))
#endif
{
deviceInfoMSD[i].flags.val |= MARK_RESET_RECOVERY;
#ifndef USB_ENABLE_TRANSFER_EVENT
deviceInfoMSD[i].returnState = STATE_RUNNING | SUBSTATE_HOLDING;
#else
deviceInfoMSD[i].returnState = STATE_RUNNING;
#endif
_USBHostMSD_ResetStateJump( i );
return USB_SUCCESS;
}
return USB_MSD_ILLEGAL_REQUEST;
}
/****************************************************************************
Function:
void USBHostMSDTasks( void )
Summary:
This function performs the maintenance tasks required by the mass storage
class.
Description:
This function performs the maintenance tasks required by the mass storage
class. If transfer events from the host layer are not being used, then
it should be called on a regular basis by the application. If transfer
events from the host layer are being used, this function is compiled out,
and does not need to be called.
Precondition:
USBHostMSDInitialize() has been called.
Parameters:
None - None
Returns:
None
Remarks:
None
***************************************************************************/
void USBHostMSDTasks( void )
{
#ifndef USB_ENABLE_TRANSFER_EVENT
DWORD byteCount;
BYTE errorCode;
BYTE i;
for (i=0; i<USB_MAX_MASS_STORAGE_DEVICES; i++)
{
if (deviceInfoMSD[i].deviceAddress != 0)
{
switch (deviceInfoMSD[i].state & STATE_MASK)
{
case STATE_DETACHED:
// No device attached.
break;
case STATE_INITIALIZE_DEVICE:
switch (deviceInfoMSD[i].state & SUBSTATE_MASK)
{
case SUBSTATE_WAIT_FOR_ENUMERATION:
if (USBHostDeviceStatus( deviceInfoMSD[i].deviceAddress ) == USB_DEVICE_ATTACHED)
{
_USBHostMSD_SetNextSubState();
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Getting max LUN...\r\n" );
#endif
}
break;
case SUBSTATE_SEND_GET_MAX_LUN:
// If we are currently sending a token, we cannot do anything.
if (U1CONbits.TOKBUSY)
break;
if (!USBHostIssueDeviceRequest( deviceInfoMSD[i].deviceAddress, USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_CLASS | USB_SETUP_RECIPIENT_INTERFACE,
USB_MSD_GET_MAX_LUN, 0, deviceInfoMSD[i].interface, 1, deviceInfoMSD[i].blockData, USB_DEVICE_REQUEST_GET, deviceInfoMSD[i].clientDriverID ))
{
_USBHostMSD_SetNextSubState();
}
else
{
// We'll try again.
}
break;
case SUBSTATE_WAIT_FOR_MAX_LUN:
if (USBHostTransferIsComplete( deviceInfoMSD[i].deviceAddress, 0, &errorCode, &byteCount ))
{
deviceInfoMSD[i].maxLUN = 0;
if (!errorCode)
{
deviceInfoMSD[i].maxLUN = deviceInfoMSD[i].blockData[0];
}
else
{
// Clear the STALL. Since it is EP0, we do not have to clear the stall.
USBHostClearEndpointErrors( deviceInfoMSD[i].deviceAddress, 0 );
}
_USBHostMSD_SetNextSubState();
}
break;
case SUBSTATE_GET_MAX_LUN_COMPLETE:
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Max LUN is " );
UART2PutHex( deviceInfoMSD[i].maxLUN );
UART2PrintString( "\r\nMSD: Running...\r\n" );
#endif
// Tell the media interface layer that we have a MSD attached.
if (usbMediaInterfaceTable.Initialize( deviceInfoMSD[i].deviceAddress, usbMediaInterfaceTable.flags, 0 ))
{
usbMediaInterfaceTable.EventHandler( deviceInfoMSD[i].deviceAddress, EVENT_MSD_MAX_LUN, &(deviceInfoMSD[i].maxLUN), 1 );
_USBHostMSD_SetNextState();
}
else
{
// The media interface layer cannot support the device.
deviceInfoMSD[i].errorCode = USB_MSD_MEDIA_INTERFACE_ERROR;
deviceInfoMSD[i].state = STATE_HOLDING;
}
break;
}
break;
case STATE_RUNNING:
switch (deviceInfoMSD[i].state & SUBSTATE_MASK)
{
case SUBSTATE_HOLDING:
break;
case SUBSTATE_SEND_CBW:
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Writing CBW\r\n" );
#endif
errorCode = USBHostWrite( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointOUT, deviceInfoMSD[i].blockData, CBW_SIZE );
if (errorCode)
{
_USBHostMSD_TerminateTransfer( errorCode );
}
else
{
_USBHostMSD_SetNextSubState();
}
break;
case SUBSTATE_CBW_WAIT:
if (USBHostTransferIsComplete( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointOUT, &errorCode, &byteCount ))
{
if (errorCode)
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Error with sending CBW\r\n" );
#endif
_USBHostMSD_TerminateTransfer( errorCode );
}
else if (byteCount != CBW_SIZE)
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: CBW size not correct\r\n" );
#endif
_USBHostMSD_TerminateTransfer( USB_MSD_CBW_ERROR );
}
else
{
if (((USB_MSD_CBW *)(deviceInfoMSD[i].blockData))->dCBWDataTransferLength == 0)
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Transfer length=0\r\n" );
#endif
// Skip to get the CSW
deviceInfoMSD[i].state = STATE_RUNNING | SUBSTATE_REQUEST_CSW;
}
else
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Going on...\r\n" );
#endif
_USBHostMSD_SetNextSubState();
}
}
}
break;
case SUBSTATE_TRANSFER_DATA:
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Transferring data, length ");
UART2PutHexDWord( deviceInfoMSD[i].userDataLength );
UART2PrintString( "\r\n" );
#endif
if (deviceInfoMSD[i].userDataLength == 0)
{
deviceInfoMSD[i].state = STATE_RUNNING | SUBSTATE_REQUEST_CSW;
}
else
{
if (!deviceInfoMSD[i].flags.bfDirection) // OUT
{
errorCode = USBHostWrite( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointDATA, deviceInfoMSD[i].userData, deviceInfoMSD[i].userDataLength );
}
else
{
errorCode = USBHostRead( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointDATA, deviceInfoMSD[i].userData, deviceInfoMSD[i].userDataLength );
}
if (errorCode)
{
_USBHostMSD_TerminateTransfer( errorCode );
}
else
{
_USBHostMSD_SetNextSubState();
}
}
break;
case SUBSTATE_TRANSFER_WAIT:
if (USBHostTransferIsComplete( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointDATA, &errorCode, &byteCount ))
{
if (errorCode)
{
if (errorCode == USB_ENDPOINT_STALLED)
{
// Clear the stall, then try to get the CSW.
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Stall on data\r\n" );
#endif
USBHostClearEndpointErrors( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointDATA );
if (!deviceInfoMSD[i].flags.bfDirection) // OUT
{
deviceInfoMSD[i].flags.bfClearDataOUT = 1;
}
else
{
deviceInfoMSD[i].flags.bfClearDataIN = 1;
}
deviceInfoMSD[i].returnState = STATE_RUNNING | SUBSTATE_REQUEST_CSW;
_USBHostMSD_ResetStateJump( i );
}
else
{
//Error recovery here is not explicitly covered in the spec. Unfortunately, some
// thumb drives generate a turn-around time error here sometimes.
//_USBHostMSD_TerminateTransfer( errorCode );
deviceInfoMSD[i].flags.val |= MARK_RESET_RECOVERY;
deviceInfoMSD[i].returnState = STATE_RUNNING | SUBSTATE_SEND_CBW; // Try the transfer again.
_USBHostMSD_ResetStateJump( i );
}
}
else
{
_USBHostMSD_SetNextSubState();
}
}
break;
case SUBSTATE_REQUEST_CSW:
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Getting CSW\r\n" );
#endif
errorCode = USBHostRead( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointIN, deviceInfoMSD[i].blockData, CSW_SIZE );
if (errorCode)
{
_USBHostMSD_TerminateTransfer( errorCode );
}
else
{
_USBHostMSD_SetNextSubState();
}
break;
case SUBSTATE_CSW_WAIT:
if (USBHostTransferIsComplete( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointIN, &errorCode, &byteCount ))
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Got CSW-" );
#endif
if (errorCode)
{
deviceInfoMSD[i].attemptsCSW--;
if (deviceInfoMSD[i].attemptsCSW)
{
USBHostClearEndpointErrors( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointIN );
deviceInfoMSD[i].flags.bfClearDataIN = 1;
deviceInfoMSD[i].returnState = STATE_RUNNING | SUBSTATE_REQUEST_CSW;
_USBHostMSD_ResetStateJump( i );
}
else
{
_USBHostMSD_TerminateTransfer( errorCode );
}
}
else if ((byteCount != CSW_SIZE) |
(((USB_MSD_CSW *)(deviceInfoMSD[i].blockData))->dCSWSignature != USB_MSD_DCSWSIGNATURE) |
(((USB_MSD_CSW *)(deviceInfoMSD[i].blockData))->dCSWTag != deviceInfoMSD[i].dCBWTag) )
{
_USBHostMSD_TerminateTransfer( USB_MSD_CSW_ERROR );
}
else
{
deviceInfoMSD[i].bytesTransferred = deviceInfoMSD[i].userDataLength - ((USB_MSD_CSW *)(deviceInfoMSD[i].blockData))->dCSWDataResidue;
if (((USB_MSD_CSW *)(deviceInfoMSD[i].blockData))->dCSWStatus != 0x00)
{
_USBHostMSD_TerminateTransfer( ((USB_MSD_CSW *)(deviceInfoMSD[i].blockData))->dCSWStatus | USB_MSD_ERROR );
}
else
{
_USBHostMSD_TerminateTransfer( USB_SUCCESS );
}
// If we have a phase error, we need to perform corrective action instead of
// returning to normal running.
if (((USB_MSD_CSW *)(deviceInfoMSD[i].blockData))->dCSWStatus == MSD_PHASE_ERROR)
{
deviceInfoMSD[i].flags.val |= MARK_RESET_RECOVERY;
deviceInfoMSD[i].returnState = STATE_RUNNING | SUBSTATE_HOLDING;
_USBHostMSD_ResetStateJump( i );
}
}
}
break;
case SUBSTATE_TRANSFER_DONE:
deviceInfoMSD[i].state = STATE_RUNNING | SUBSTATE_HOLDING;
#ifdef USB_MSD_ENABLE_TRANSFER_EVENT
usbMediaInterfaceTable.EventHandler( deviceInfoMSD[i].deviceAddress, EVENT_MSD_TRANSFER, NULL, 0 );
#endif
break;
}
break;
case STATE_MSD_RESET_RECOVERY:
switch (deviceInfoMSD[i].state & SUBSTATE_MASK)
{
case SUBSTATE_SEND_RESET:
errorCode = USBHostIssueDeviceRequest( deviceInfoMSD[i].deviceAddress, USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_CLASS | USB_SETUP_RECIPIENT_INTERFACE,
USB_MSD_RESET, 0, deviceInfoMSD[i].interface, 0, NULL, USB_DEVICE_REQUEST_SET, deviceInfoMSD[i].clientDriverID );
if (errorCode)
{
//Error recovery here is not explicitly covered in the spec.
_USBHostMSD_TerminateTransfer( USB_MSD_RESET_ERROR );
}
else
{
_USBHostMSD_SetNextSubState();
}
break;
case SUBSTATE_WAIT_FOR_RESET:
if (USBHostTransferIsComplete( deviceInfoMSD[i].deviceAddress, 0, &errorCode, &byteCount ))
{
if (errorCode)
{
//Error recovery here is not explicitly covered in the spec.
_USBHostMSD_TerminateTransfer( USB_MSD_RESET_ERROR );
}
else
{
deviceInfoMSD[i].flags.bfReset = 0;
_USBHostMSD_SetNextSubState();
}
}
break;
case SUBSTATE_RESET_COMPLETE:
_USBHostMSD_ResetStateJump( i );
break;
}
break;
case STATE_MSD_CLEAR_DATA_IN:
switch (deviceInfoMSD[i].state & SUBSTATE_MASK)
{
case SUBSTATE_SEND_CLEAR_IN:
errorCode = USBHostIssueDeviceRequest( deviceInfoMSD[i].deviceAddress, USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_ENDPOINT,
USB_REQUEST_CLEAR_FEATURE, USB_FEATURE_ENDPOINT_HALT, deviceInfoMSD[i].endpointIN, 0, NULL, USB_DEVICE_REQUEST_SET, deviceInfoMSD[i].clientDriverID );
if (errorCode)
{
//Error recovery here is not explicitly covered in the spec.
_USBHostMSD_TerminateTransfer( USB_MSD_RESET_ERROR );
}
else
{
_USBHostMSD_SetNextSubState();
}
break;
case SUBSTATE_WAIT_FOR_CLEAR_IN:
if (USBHostTransferIsComplete( deviceInfoMSD[i].deviceAddress, 0, &errorCode, &byteCount ))
{
if (errorCode)
{
//Error recovery here is not explicitly covered in the spec.
_USBHostMSD_TerminateTransfer( USB_MSD_RESET_ERROR );
}
else
{
deviceInfoMSD[i].flags.bfClearDataIN = 0;
_USBHostMSD_SetNextSubState();
}
}
break;
case SUBSTATE_CLEAR_IN_COMPLETE:
_USBHostMSD_ResetStateJump( i );
break;
}
break;
case STATE_MSD_CLEAR_DATA_OUT:
switch (deviceInfoMSD[i].state & SUBSTATE_MASK)
{
case SUBSTATE_SEND_CLEAR_OUT:
errorCode = USBHostIssueDeviceRequest( deviceInfoMSD[i].deviceAddress, USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_ENDPOINT,
USB_REQUEST_CLEAR_FEATURE, USB_FEATURE_ENDPOINT_HALT, deviceInfoMSD[i].endpointOUT, 0, NULL, USB_DEVICE_REQUEST_SET, deviceInfoMSD[i].clientDriverID );
if (errorCode)
{
//Error recovery here is not explicitly covered in the spec.
_USBHostMSD_TerminateTransfer( USB_MSD_RESET_ERROR );
}
else
{
_USBHostMSD_SetNextSubState();
}
break;
case SUBSTATE_WAIT_FOR_CLEAR_OUT:
if (USBHostTransferIsComplete( deviceInfoMSD[i].deviceAddress, 0, &errorCode, &byteCount ))
{
if (errorCode)
{
//Error recovery here is not explicitly covered in the spec.
_USBHostMSD_TerminateTransfer( USB_MSD_RESET_ERROR );
}
else
{
deviceInfoMSD[i].flags.bfClearDataOUT = 0;
_USBHostMSD_SetNextSubState();
}
}
break;
case SUBSTATE_CLEAR_OUT_COMPLETE:
_USBHostMSD_ResetStateJump( i );
break;
}
break;
case STATE_HOLDING:
break;
}
}
}
#endif
}
/****************************************************************************
Function:
void USBHostMSDTerminateTransfer( BYTE deviceAddress )
Description:
This function terminates a mass storage transfer.
Precondition:
None
Parameters:
BYTE deviceAddress - Device address
Returns:
None
Remarks:
After executing this function, the application may have to reset the
device in order for the device to continue working properly.
***************************************************************************/
void USBHostMSDTerminateTransfer( BYTE deviceAddress )
{
BYTE i;
// Find the correct device.
for (i=0; (i<USB_MAX_MASS_STORAGE_DEVICES) && (deviceInfoMSD[i].deviceAddress != deviceAddress); i++);
if (i == USB_MAX_MASS_STORAGE_DEVICES)
{
return;
}
// We can only terminate transfers if we are in STATE_RUNNING. Otherwise, we
// will cause major problems.
#ifndef USB_ENABLE_TRANSFER_EVENT
if ((deviceInfoMSD[i].state & STATE_MASK) == STATE_RUNNING)
#else
if ((deviceInfoMSD[i].state == STATE_RUNNING) ||
(deviceInfoMSD[i].state == STATE_CBW_WAIT) ||
(deviceInfoMSD[i].state == STATE_TRANSFER_WAIT) ||
(deviceInfoMSD[i].state == STATE_CSW_WAIT))
#endif
{
// Terminate any endpoint tranfers that are occurring.
USBHostTerminateTransfer( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointIN );
USBHostTerminateTransfer( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointOUT );
// Set the state back to running and waiting for a transfer request.
#ifndef USB_ENABLE_TRANSFER_EVENT
deviceInfoMSD[i].state = STATE_RUNNING | SUBSTATE_HOLDING;
#else
deviceInfoMSD[i].state = STATE_RUNNING;
#endif
}
return;
}
/****************************************************************************
Function:
BYTE USBHostMSDTransfer( BYTE deviceAddress, BYTE deviceLUN,
BYTE direction, BYTE *commandBlock, BYTE commandBlockLength,
BYTE *data, DWORD dataLength )
Summary:
This function starts a mass storage transfer.
Description:
This function starts a mass storage transfer. Usually, applications will
probably utilize a read/write wrapper to access this function.
Precondition:
None
Parameters:
BYTE deviceAddress - Device address
BYTE deviceLUN - Device LUN to access
BYTE direction - 1=read, 0=write
BYTE *commandBlock - Pointer to the command block for the CBW
BYTE commandBlockLength - Length of the command block
BYTE *data - Pointer to the data buffer
DWORD dataLength - Byte size of the data buffer
Return Values:
USB_SUCCESS - Request started successfully
USB_MSD_DEVICE_NOT_FOUND - No device with specified address
USB_MSD_DEVICE_BUSY - Device not in proper state for performing
a transfer
USB_MSD_INVALID_LUN - Specified LUN does not exist
Remarks:
None
***************************************************************************/
BYTE USBHostMSDTransfer( BYTE deviceAddress, BYTE deviceLUN, BYTE direction, BYTE *commandBlock,
BYTE commandBlockLength, BYTE *data, DWORD dataLength )
{
BYTE i;
BYTE j;
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Transfer: " );
if (direction)
{
UART2PrintString( "Read, " );
}
else
{
UART2PrintString( "Write, " );
}
#endif
// Make sure a valid device is being requested.
if ((deviceAddress == 0) || (deviceAddress > 127))
{
return USB_MSD_DEVICE_NOT_FOUND;
}
// Find the correct device.
for (i=0; (i<USB_MAX_MASS_STORAGE_DEVICES) && (deviceInfoMSD[i].deviceAddress != deviceAddress); i++);
if (i == USB_MAX_MASS_STORAGE_DEVICES)
{
return USB_MSD_DEVICE_NOT_FOUND;
}
// Make sure the device is in a state ready to read/write.
#ifndef USB_ENABLE_TRANSFER_EVENT
if (deviceInfoMSD[i].state != (STATE_RUNNING | SUBSTATE_HOLDING))
#else
if (deviceInfoMSD[i].state != STATE_RUNNING)
#endif
{
return USB_MSD_DEVICE_BUSY;
}
// Verify the selected LUN.
if (deviceLUN > deviceInfoMSD[i].maxLUN)
{
return USB_MSD_INVALID_LUN;
}
// Initialize the transfer information.
deviceInfoMSD[i].attemptsCSW = CSW_RECEIVE_ATTEMPTS;
deviceInfoMSD[i].bytesTransferred = 0;
deviceInfoMSD[i].errorCode = USB_SUCCESS;
deviceInfoMSD[i].flags.val = 0;
deviceInfoMSD[i].flags.bfDirection = direction;
deviceInfoMSD[i].userData = data;
deviceInfoMSD[i].userDataLength = dataLength;
deviceInfoMSD[i].dCBWTag = _USBHostMSD_GetNextTag();
deviceInfoMSD[i].endpointDATA = deviceInfoMSD[i].endpointIN;
if (!direction) // OUT
{
deviceInfoMSD[i].endpointDATA = deviceInfoMSD[i].endpointOUT;
}
#ifdef DEBUG_MODE
UART2PrintString( "Data EP: " );
UART2PutHex( deviceInfoMSD[i].endpointDATA );
UART2PrintString( "\r\n" );
#endif
// Prepare the CBW so we can give the user back his command block RAM.
((USB_MSD_CBW *)(deviceInfoMSD[i].blockData))->dCBWSignature = USB_MSD_DCBWSIGNATURE;
((USB_MSD_CBW *)(deviceInfoMSD[i].blockData))->dCBWTag = deviceInfoMSD[i].dCBWTag;
((USB_MSD_CBW *)(deviceInfoMSD[i].blockData))->dCBWDataTransferLength = deviceInfoMSD[i].userDataLength;
((USB_MSD_CBW *)(deviceInfoMSD[i].blockData))->bmCBWflags.val = 0;
((USB_MSD_CBW *)(deviceInfoMSD[i].blockData))->bmCBWflags.bfDirection = direction;
((USB_MSD_CBW *)(deviceInfoMSD[i].blockData))->bCBWLUN = deviceLUN;
((USB_MSD_CBW *)(deviceInfoMSD[i].blockData))->bCBWCBLength = commandBlockLength;
for (j=0; j<commandBlockLength; j++)
{
((USB_MSD_CBW *)(deviceInfoMSD[i].blockData))->CBWCB[j] = commandBlock[j];
}
#ifndef USB_ENABLE_TRANSFER_EVENT
// Jump to the transfer state.
deviceInfoMSD[i].state = STATE_RUNNING | SUBSTATE_SEND_CBW;
#else
j = USBHostWrite( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointOUT, deviceInfoMSD[i].blockData, CBW_SIZE );
if (j)
{
_USBHostMSD_TerminateTransfer( j );
}
else
{
deviceInfoMSD[i].state = STATE_CBW_WAIT;
}
#endif
return USB_SUCCESS;
}
/****************************************************************************
Function:
BOOL USBHostMSDTransferIsComplete( BYTE deviceAddress,
BYTE *errorCode, DWORD *byteCount )
Summary:
This function indicates whether or not the last transfer is complete.
Description:
This function indicates whether or not the last transfer is complete. If
the functions returns TRUE, the returned byte count and error code are
valid. Since only one transfer can be performed at once and only one
endpoint can be used, we only need to know the device address.
Precondition:
None
Parameters:
BYTE deviceAddress - Device address
BYTE *errorCode - Error code from last transfer
DWORD *byteCount - Number of bytes transferred
Return Values:
TRUE - Transfer is complete, errorCode is valid
FALSE - Transfer is not complete, errorCode is not valid
Remarks:
None
***************************************************************************/
BOOL USBHostMSDTransferIsComplete( BYTE deviceAddress, BYTE *errorCode, DWORD *byteCount )
{
BYTE i;
// Make sure a valid device is being requested.
if ((deviceAddress == 0) || (deviceAddress > 127))
{
*errorCode = USB_MSD_DEVICE_NOT_FOUND;
*byteCount = 0;
return TRUE;
}
// Find the correct device.
for (i=0; (i<USB_MAX_MASS_STORAGE_DEVICES) && (deviceInfoMSD[i].deviceAddress != deviceAddress); i++);
if ((i == USB_MAX_MASS_STORAGE_DEVICES) || (deviceInfoMSD[i].state == STATE_DETACHED))
{
*errorCode = USB_MSD_DEVICE_NOT_FOUND;
*byteCount = 0;
return TRUE;
}
#ifndef USB_ENABLE_TRANSFER_EVENT
if ( (deviceInfoMSD[i].state == (STATE_RUNNING | SUBSTATE_HOLDING)) ||
((deviceInfoMSD[i].state & STATE_MASK) == STATE_HOLDING))
#else
if ((deviceInfoMSD[i].state == STATE_RUNNING) ||
(deviceInfoMSD[i].state == STATE_HOLDING))
#endif
{
*byteCount = deviceInfoMSD[i].bytesTransferred;
*errorCode = deviceInfoMSD[i].errorCode;
return TRUE;
}
else
{
return FALSE;
}
}
// *****************************************************************************
// *****************************************************************************
// Section: Host Stack Interface Functions
// *****************************************************************************
// *****************************************************************************
/****************************************************************************
Function:
BOOL USBHostMSDInitialize( BYTE address, DWORD flags, BYTE clientDriverID )
Summary:
This function is the initialization routine for this client driver.
Description:
This function is the initialization routine for this client driver. It
is called by the host layer when the USB device is being enumerated. For
a mass storage device, we need to make sure that we have room for a new
device, and that the device has at least one bulk IN and one bulk OUT
endpoint.
Precondition:
None
Parameters:
BYTE address - Address of the new device
DWORD flags - Initialization flags
BYTE clientDriverID - ID to send when issuing a Device Request via
USBHostIssueDeviceRequest(), USBHostSetDeviceConfiguration(),
or USBHostSetDeviceInterface().
Return Values:
TRUE - We can support the device.
FALSE - We cannot support the device.
Remarks:
None
***************************************************************************/
BOOL USBHostMSDInitialize( BYTE address, DWORD flags, BYTE clientDriverID )
{
BYTE *descriptor;
BYTE device;
#ifdef USB_ENABLE_TRANSFER_EVENT
BYTE errorCode;
#endif
WORD i;
BYTE endpointIN;
BYTE endpointOUT;
#ifdef DEBUG_MODE
UART2PrintString( "MSD: USBHostMSDClientInitialize(0x" );
UART2PutHex( flags );
UART2PrintString( ")\r\n" );
#endif
// Find the free slot in the table. If we cannot find one, kick off the device.
for (device = 0; (device < USB_MAX_MASS_STORAGE_DEVICES) && (deviceInfoMSD[device].deviceAddress != 0); device++);
if (device == USB_MAX_MASS_STORAGE_DEVICES)
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: No free slots available for MSD.\r\n" );
#endif
// Kick off the device
return FALSE;
}
#ifdef DEBUG_MODE
UART2PrintString( "MSD: MSD attached.\r\n" );
#endif
descriptor = USBHostGetCurrentConfigurationDescriptor( address );
i = 0;
#ifdef DEBUG_MODE
UART2PrintString("MSD: Checking descriptor " );
UART2PutDec( descriptor[i+5] );
UART2PrintString(" ...\r\n" );
#endif
// Find the next interface descriptor.
while (i < ((USB_CONFIGURATION_DESCRIPTOR *)descriptor)->wTotalLength)
{
#ifdef DEBUG_MODE
UART2PrintString("MSD: Checking interface...\r\n" );
#endif
// See if we are pointing to an interface descriptor.
if (descriptor[i+1] == USB_DESCRIPTOR_INTERFACE)
{
// See if the interface is a Mass Storage Device interface.
if (descriptor[i+5] == DEVICE_CLASS_MASS_STORAGE)
{
// See if the interface subclass and protocol are correct.
if ((descriptor[i+6] == DEVICE_SUBCLASS_SCSI) &&
(descriptor[i+7] == DEVICE_INTERFACE_PROTOCOL_BULK_ONLY))
{
deviceInfoMSD[device].interface = descriptor[i+2];
// Look for bulk IN and OUT endpoints.
endpointIN = 0;
endpointOUT = 0;
// Scan for endpoint descriptors.
i += descriptor[i];
while (descriptor[i+1] == USB_DESCRIPTOR_ENDPOINT)
{
if (descriptor[i+3] == 0x02) // Bulk
{
if (((descriptor[i+2] & 0x80) == 0x80) && (endpointIN == 0))
{
endpointIN = descriptor[i+2];
}
if (((descriptor[i+2] & 0x80) == 0x00) && (endpointOUT == 0))
{
endpointOUT = descriptor[i+2];
}
}
i += descriptor[i];
}
if ((endpointIN != 0) && (endpointOUT != 0))
{
// Initialize the device information.
deviceInfoMSD[device].deviceAddress = address;
deviceInfoMSD[device].clientDriverID = clientDriverID;
deviceInfoMSD[device].endpointIN = endpointIN;
deviceInfoMSD[device].endpointOUT = endpointOUT;
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Bulk endpoint IN: " );
UART2PutHex( endpointIN );
UART2PrintString( " Bulk endpoint OUT: " );
UART2PutHex( endpointOUT );
UART2PrintString( "\r\n" );
#endif
USBHostSetNAKTimeout( address, endpointIN, 1, USB_NUM_BULK_NAKS );
USBHostSetNAKTimeout( address, endpointOUT, 1, USB_NUM_BULK_NAKS );
#ifndef USB_ENABLE_TRANSFER_EVENT
deviceInfoMSD[device].state = STATE_INITIALIZE_DEVICE;
#else
// Initiate the request to get the max LUN. If we can't initiate the request,
// then we can't enumerate the device.
errorCode = USBHostIssueDeviceRequest( deviceInfoMSD[device].deviceAddress,
USB_SETUP_DEVICE_TO_HOST | USB_SETUP_TYPE_CLASS | USB_SETUP_RECIPIENT_INTERFACE,
USB_MSD_GET_MAX_LUN, 0, deviceInfoMSD[device].interface, 1, deviceInfoMSD[device].blockData,
USB_DEVICE_REQUEST_GET, deviceInfoMSD[device].clientDriverID );
if (errorCode)
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Cannot get Max LUN - " );
UART2PutHex( errorCode );
UART2PrintString( "\r\n" );
#endif
return FALSE;
}
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Getting Max LUN\r\n" );
#endif
deviceInfoMSD[device].state = STATE_WAIT_FOR_MAX_LUN;
#endif
return TRUE;
}
}
}
}
// Jump to the next descriptor in this configuration.
i += descriptor[i];
}
// This configuration is not valid for a Mass storage device.
return FALSE;
}
/****************************************************************************
Function:
BOOL USBHostMSDEventHandler( BYTE address, USB_EVENT event,
void *data, DWORD size )
Summary:
This function is the event handler for this client driver.
Description:
This function is the event handler for this client driver. It is called
by the host layer when various events occur.
Precondition:
The device has been initialized.
Parameters:
BYTE address - Address of the device
USB_EVENT event - Event that has occurred
void *data - Pointer to data pertinent to the event
WORD size - Size of the data
Return Values:
TRUE - Event was handled
FALSE - Event was not handled
Remarks:
None
***************************************************************************/
BOOL USBHostMSDEventHandler( BYTE address, USB_EVENT event, void *data, DWORD size )
{
#if defined( USB_ENABLE_TRANSFER_EVENT )
BYTE errorCode;
#endif
BYTE i;
switch (event)
{
case EVENT_NONE: // No event occured (NULL event)
USBTasks();
return TRUE;
break;
case EVENT_DETACH: // USB cable has been detached (data: BYTE, address of device)
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Detach\r\n" );
#endif
// Find the device in the table. If found, clear the important fields.
for (i=0; (i<USB_MAX_MASS_STORAGE_DEVICES) && (deviceInfoMSD[i].deviceAddress != address); i++);
if (i < USB_MAX_MASS_STORAGE_DEVICES)
{
deviceInfoMSD[i].deviceAddress = 0;
deviceInfoMSD[i].state = STATE_DETACHED;
// Inform the next higher layer of the event.
usbMediaInterfaceTable.EventHandler( address, EVENT_DETACH, NULL, 0 );
}
return TRUE;
break;
case EVENT_TRANSFER: // A USB transfer has completed - optional
#if defined( USB_ENABLE_TRANSFER_EVENT )
#ifdef DEBUG_MODE
UART2PrintString( "MSD: transfer event: " );
UART2PutHex( address );
UART2PrintString( "\r\n" );
#endif
for (i=0; (i<USB_MAX_MASS_STORAGE_DEVICES) && (deviceInfoMSD[i].deviceAddress != address); i++) {}
if (i == USB_MAX_MASS_STORAGE_DEVICES)
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Unknown device\r\n" );
#endif
return FALSE;
}
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Device state: " );
UART2PutHex( deviceInfoMSD[i].state );
UART2PrintString( "\r\n" );
#endif
switch (deviceInfoMSD[i].state)
{
case STATE_WAIT_FOR_MAX_LUN:
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Got Max LUN\r\n" );
#endif
deviceInfoMSD[i].maxLUN = 0;
if (!((HOST_TRANSFER_DATA *)data)->bErrorCode)
{
deviceInfoMSD[i].maxLUN = deviceInfoMSD[i].blockData[0];
}
else
{
// Clear the STALL. Since it is EP0, we do not have to clear the stall.
USBHostClearEndpointErrors( deviceInfoMSD[i].deviceAddress, 0 );
}
// Tell the media interface layer that we have a MSD attached.
if (usbMediaInterfaceTable.Initialize( deviceInfoMSD[i].deviceAddress, usbMediaInterfaceTable.flags, 0 ))
{
usbMediaInterfaceTable.EventHandler( deviceInfoMSD[i].deviceAddress, EVENT_MSD_MAX_LUN, &(deviceInfoMSD[i].maxLUN), 1 );
deviceInfoMSD[i].state = STATE_RUNNING;
}
else
{
// The media interface layer cannot support the device.
deviceInfoMSD[i].errorCode = USB_MSD_MEDIA_INTERFACE_ERROR;
deviceInfoMSD[i].state = STATE_HOLDING;
}
return TRUE;
break;
case STATE_RUNNING:
// Shouldn't get any transfer events here.
return FALSE;
break;
case STATE_CBW_WAIT:
if (((HOST_TRANSFER_DATA *)data)->bErrorCode)
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Error with sending CBW\r\n" );
#endif
_USBHostMSD_TerminateTransfer( ((HOST_TRANSFER_DATA *)data)->bErrorCode );
}
else if (((HOST_TRANSFER_DATA *)data)->dataCount != CBW_SIZE)
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: CBW size not correct\r\n" );
#endif
_USBHostMSD_TerminateTransfer( USB_MSD_CBW_ERROR );
}
else
{
if ((((USB_MSD_CBW *)(deviceInfoMSD[i].blockData))->dCBWDataTransferLength == 0) ||
(deviceInfoMSD[i].userDataLength == 0))
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Transfer length=0\r\n" );
#endif
// Skip to getting the CSW
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Getting CSW\r\n" );
#endif
errorCode = USBHostRead( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointIN, deviceInfoMSD[i].blockData, CSW_SIZE );
if (errorCode)
{
_USBHostMSD_TerminateTransfer( errorCode );
}
else
{
deviceInfoMSD[i].state = STATE_CSW_WAIT;
}
}
else
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Going on...\r\n" );
#endif
if (!deviceInfoMSD[i].flags.bfDirection) // OUT
{
errorCode = USBHostWrite( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointDATA, deviceInfoMSD[i].userData, deviceInfoMSD[i].userDataLength );
}
else
{
errorCode = USBHostRead( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointDATA, deviceInfoMSD[i].userData, deviceInfoMSD[i].userDataLength );
}
if (errorCode)
{
_USBHostMSD_TerminateTransfer( errorCode );
}
else
{
deviceInfoMSD[i].state = STATE_TRANSFER_WAIT;
}
}
}
return TRUE;
break;
case STATE_TRANSFER_WAIT:
if (((HOST_TRANSFER_DATA *)data)->bErrorCode)
{
if (((HOST_TRANSFER_DATA *)data)->bErrorCode == USB_ENDPOINT_STALLED)
{
// Clear the stall, then try to get the CSW.
USBHostClearEndpointErrors( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointDATA );
if (!deviceInfoMSD[i].flags.bfDirection) // OUT
{
deviceInfoMSD[i].flags.bfClearDataOUT = 1;
}
else
{
deviceInfoMSD[i].flags.bfClearDataIN = 1;
}
deviceInfoMSD[i].returnState = STATE_REQUEST_CSW;
_USBHostMSD_ResetStateJump( i );
}
else
{
//Error recovery here is not explicitly covered in the spec.
//_USBHostMSD_TerminateTransfer( errorCode );
deviceInfoMSD[i].flags.val |= MARK_RESET_RECOVERY;
deviceInfoMSD[i].returnState = STATE_RUNNING;
_USBHostMSD_ResetStateJump( i );
}
}
else
{
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Getting CSW\r\n" );
#endif
errorCode = USBHostRead( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointIN, deviceInfoMSD[i].blockData, CSW_SIZE );
if (errorCode)
{
_USBHostMSD_TerminateTransfer( errorCode );
}
else
{
deviceInfoMSD[i].state = STATE_CSW_WAIT;
}
}
break;
case STATE_CSW_WAIT:
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Got CSW - " );
#endif
if (((HOST_TRANSFER_DATA *)data)->bErrorCode)
{
deviceInfoMSD[i].attemptsCSW--;
if (deviceInfoMSD[i].attemptsCSW)
{
USBHostClearEndpointErrors( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointIN );
deviceInfoMSD[i].flags.bfClearDataIN = 1;
deviceInfoMSD[i].returnState = STATE_REQUEST_CSW;
_USBHostMSD_ResetStateJump( i );
}
else
{
_USBHostMSD_TerminateTransfer( ((HOST_TRANSFER_DATA *)data)->bErrorCode );
}
}
else if ((((HOST_TRANSFER_DATA *)data)->dataCount != CSW_SIZE) |
(((USB_MSD_CSW *)(deviceInfoMSD[i].blockData))->dCSWSignature != USB_MSD_DCSWSIGNATURE) |
(((USB_MSD_CSW *)(deviceInfoMSD[i].blockData))->dCSWTag != deviceInfoMSD[i].dCBWTag) )
{
_USBHostMSD_TerminateTransfer( USB_MSD_CSW_ERROR );
}
else
{
deviceInfoMSD[i].bytesTransferred = deviceInfoMSD[i].userDataLength - ((USB_MSD_CSW *)(deviceInfoMSD[i].blockData))->dCSWDataResidue;
if (((USB_MSD_CSW *)(deviceInfoMSD[i].blockData))->dCSWStatus != 0x00)
{
_USBHostMSD_TerminateTransfer( ((USB_MSD_CSW *)(deviceInfoMSD[i].blockData))->dCSWStatus | USB_MSD_ERROR );
}
else
{
_USBHostMSD_TerminateTransfer( USB_SUCCESS );
}
// If we have a phase error, we need to perform corrective action instead of
// returning to normal running.
if (((USB_MSD_CSW *)(deviceInfoMSD[i].blockData))->dCSWStatus == MSD_PHASE_ERROR)
{
deviceInfoMSD[i].flags.val |= MARK_RESET_RECOVERY;
deviceInfoMSD[i].returnState = STATE_RUNNING;
_USBHostMSD_ResetStateJump( i );
}
}
break;
case STATE_WAIT_FOR_RESET:
if (((HOST_TRANSFER_DATA *)data)->bErrorCode)
{
//Error recovery here is not explicitly covered in the spec.
_USBHostMSD_TerminateTransfer( USB_MSD_RESET_ERROR );
}
else
{
deviceInfoMSD[i].flags.bfReset = 0;
_USBHostMSD_ResetStateJump( i );
}
break;
case STATE_WAIT_FOR_CLEAR_IN:
if (errorCode)
{
//Error recovery here is not explicitly covered in the spec.
_USBHostMSD_TerminateTransfer( USB_MSD_RESET_ERROR );
}
else
{
deviceInfoMSD[i].flags.bfClearDataIN = 0;
_USBHostMSD_ResetStateJump( i );
}
break;
case STATE_WAIT_FOR_CLEAR_OUT:
if (errorCode)
{
//Error recovery here is not explicitly covered in the spec.
_USBHostMSD_TerminateTransfer( USB_MSD_RESET_ERROR );
}
else
{
deviceInfoMSD[i].flags.bfClearDataOUT = 0;
_USBHostMSD_ResetStateJump( i );
}
break;
case STATE_HOLDING:
break;
}
#endif
case EVENT_SOF: // Start of frame - NOT NEEDED
case EVENT_RESUME: // Device-mode resume received
case EVENT_SUSPEND: // Device-mode suspend/idle event received
case EVENT_RESET: // Device-mode bus reset received
case EVENT_STALL: // A stall has occured
return TRUE;
break;
default:
return FALSE;
break;
}
return FALSE;
}
// *****************************************************************************
// *****************************************************************************
// Section: Internal Functions
// *****************************************************************************
// *****************************************************************************
/****************************************************************************
Function:
DWORD _USBHostMSD_GetNextTag( void )
Description:
Each bulk transfer has a transfer ID that is present in the CBW and must
match in the CWS. This function gets the next ID number for a transfer.
Precondition:
None
Parameters:
None - None
Returns:
DWORD - Tag to use in the next CBW
Remarks:
None
***************************************************************************/
DWORD _USBHostMSD_GetNextTag( void )
{
return dCBWTagNext++;
}
/****************************************************************************
Function:
void _USBHostMSD_ResetStateJump( BYTE i )
Summary:
Description:
This function determines which portion of the reset processing needs to
be executed next and jumps to that state.
Precondition:
The device information must be in the deviceInfoMSD array.
Parameters:
BYTE i - Index into the deviceInfoMSD structure for the device to reset.
Returns:
None
Remarks:
None
***************************************************************************/
void _USBHostMSD_ResetStateJump( BYTE i )
{
#ifdef USB_ENABLE_TRANSFER_EVENT
BYTE errorCode;
#endif
if (deviceInfoMSD[i].flags.bfReset)
{
#ifndef USB_ENABLE_TRANSFER_EVENT
deviceInfoMSD[i].state = STATE_MSD_RESET_RECOVERY;
#else
errorCode = USBHostIssueDeviceRequest( deviceInfoMSD[i].deviceAddress, USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_CLASS | USB_SETUP_RECIPIENT_INTERFACE,
USB_MSD_RESET, 0, deviceInfoMSD[i].interface, 0, NULL, USB_DEVICE_REQUEST_SET, deviceInfoMSD[i].clientDriverID );
if (errorCode)
{
//Error recovery here is not explicitly covered in the spec.
_USBHostMSD_TerminateTransfer( USB_MSD_RESET_ERROR );
}
else
{
deviceInfoMSD[i].state = STATE_WAIT_FOR_RESET;
}
#endif
}
else if (deviceInfoMSD[i].flags.bfClearDataIN)
{
#ifndef USB_ENABLE_TRANSFER_EVENT
deviceInfoMSD[i].state = STATE_MSD_CLEAR_DATA_IN;
#else
errorCode = USBHostIssueDeviceRequest( deviceInfoMSD[i].deviceAddress, USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_ENDPOINT,
USB_REQUEST_CLEAR_FEATURE, USB_FEATURE_ENDPOINT_HALT, deviceInfoMSD[i].endpointIN, 0, NULL, USB_DEVICE_REQUEST_SET, deviceInfoMSD[i].clientDriverID );
if (errorCode)
{
//Error recovery here is not explicitly covered in the spec.
_USBHostMSD_TerminateTransfer( USB_MSD_RESET_ERROR );
}
else
{
deviceInfoMSD[i].state = STATE_WAIT_FOR_CLEAR_IN;
}
#endif
}
else if (deviceInfoMSD[i].flags.bfClearDataOUT)
{
#ifndef USB_ENABLE_TRANSFER_EVENT
deviceInfoMSD[i].state = STATE_MSD_CLEAR_DATA_OUT;
#else
errorCode = USBHostIssueDeviceRequest( deviceInfoMSD[i].deviceAddress, USB_SETUP_HOST_TO_DEVICE | USB_SETUP_TYPE_STANDARD | USB_SETUP_RECIPIENT_ENDPOINT,
USB_REQUEST_CLEAR_FEATURE, USB_FEATURE_ENDPOINT_HALT, deviceInfoMSD[i].endpointOUT, 0, NULL, USB_DEVICE_REQUEST_SET, deviceInfoMSD[i].clientDriverID );
if (errorCode)
{
//Error recovery here is not explicitly covered in the spec.
_USBHostMSD_TerminateTransfer( USB_MSD_RESET_ERROR );
}
else
{
deviceInfoMSD[i].state = STATE_WAIT_FOR_CLEAR_OUT;
}
#endif
}
else
{
usbMediaInterfaceTable.EventHandler( deviceInfoMSD[i].deviceAddress, EVENT_MSD_RESET, NULL, 0 );
// Clear the errors so we can try again.
USBHostClearEndpointErrors( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointIN );
USBHostClearEndpointErrors( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointOUT );
#ifndef USB_ENABLE_TRANSFER_EVENT
deviceInfoMSD[i].state = deviceInfoMSD[i].returnState;
#else
if (deviceInfoMSD[i].returnState == STATE_REQUEST_CSW)
{
// Request the CSW
#ifdef DEBUG_MODE
UART2PrintString( "MSD: Getting CSW\r\n" );
#endif
errorCode = USBHostRead( deviceInfoMSD[i].deviceAddress, deviceInfoMSD[i].endpointIN, deviceInfoMSD[i].blockData, CSW_SIZE );
if (errorCode)
{
_USBHostMSD_TerminateTransfer( errorCode );
}
else
{
deviceInfoMSD[i].state = STATE_CSW_WAIT;
}
}
else
{
deviceInfoMSD[i].state = deviceInfoMSD[i].returnState;
}
#endif
}
}
|